Home»Clearance Corner»ELB 3 - 15 Ply Orrsom Longboard, 2x VESC 6, 14Fifties Red Plug Denim Wedge Bushings, 185kv Motors, 15/66, Superstar Wheels with 6.5 inch Urban Treads Tyres

Cable Router for ORRSOM Longboard

The ORRSOM Longboard Cable Router sits between the rear truck & battery tray, neatly routing the cables from the VESCs to the Motors while protecting them from knocks and snags commonly experience with under-mounted electronics. 

ORRSOM Longboard Under board Battery Tray - Ready to fit

TRAMPA's ORRSOM Underboard Battery Tray is produced in long strips of up to nearly 2 meters in length. It is supplied to us as long lengths where we cut it down by hand to size to suit the customers requirements & we also send some of the long lengths to the water cutters where it is precision cut with water & the CNC machnine to our exact length & requirement to fit perfectly to the ORRSOM longboard Deck.

Measuring 26mm deep the tray is relatively shallow which arguably restricts its battery capacity & consequently its range, everybody knows TRAMPA is famous for good range & performance.... o

Originally developed to squeeze in to the Tray space 6× 10000mAh 2s Li-Po Cells,. This combination gave a amazing range of up to 25 kilometers (70kg rider) & a very punchy 12s performance when riding the STICKIES wheels (The ORRSOM Board was developed originally to be a Longboard using Longboard wheels where you do for sure get much better range performance) gave over 25km's of range when running on good surface at relatively constant high speed which was loads of performance, but we had problems with the supply of the batteries & the wiring together of the 6x 2s Li-Po cells was quite complicated, specially when it came to the charging, we just thought it was too much for the general public to deal with so we now suggest fitting a 12S 3P Lithium-Ion pack using the 18650 cells which gives pretty much the same range & almost the same punchy performance as the Li-Po Cells

Although the battery tray is quite shallow, being made from the same material as the deck it gives a very stealthy look & when you purchase the complete Watercut/CNC Battery Tray as a kit to fit to the deck, it fits llke a glove to the ORRSOM longboard deck! PLUS, the Structure

It was possible to House 6x 2s 10000mAH HRB High performance Cells to give you ORRSOM long range & amazing 12s power when using the STICKIES wheels!!

You can purchase the raw battery tray in lengths of 10 cm's, whereas if you had to the battery box pages you can purchase the complete awesome underfloor battery tray with all the fixing parts required...  The ORRSOM Underboard Battery Tray comes supplied with CNC Anodised End Bungs, Rubber Grommets silicone seals & strips of foam to be able to seal your deck off to be waterproof!

ORRSOM Longboard Underboard Battery Tray T6 FRONT-END Support Bung

A tightly fitting END Bung for Underboard Battery Trays. Keeps your batteries safe & protected from the elements, whilst looking stylish with an embossed TRAMPA Logo.

ORRSOM Longboard Underboard Battery Tray T6 REAR-END Cable routing Support Bung

A tightly fitting END bung for Underboard Battery Trays - specially designed holes allow power & sensor cables to flow in and out of the battery box, while keeping the elements out.

400mm long x 15mm wide High Torque Drive (HTD) 5M (5mm Tooth Space) High Power (HP) STRONGBELT

This ia 400mm long x 15mm wide High Torque Drive (HTD) Re-enforced Rubber Belt, which has 5mm Tooth Spacing (5M). This Belt is High Power rated (HP) & arguably over engineered for our application as the belt is made in Germany by the world famous company called STRONGBELT, who usually supply into heavy industry public sector applications which demand much more stringent requirements of any electric skateboard! This belt is used to transfer the power from the Motor & Motor Pulley into power at the rear wheels of a TRAMPA....

TRAMPA opted to set a new standard in E-Skating, becoming the first in the world to fit to all of its E-Boards, a 15mm wide TRANSMISSON BELT. Our standard 15mm belt is almost double the width of nearly all other E-Sk8's out there, they tend to use a flimsy off the shelf 9mm transmission belt which are prone to stretch, slip & ultimately snap. Using a re-enforced 15mm wide High Power Belt reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. When accelerating or engine breaking (KERS), even from a standing start the STRONGBELT power is smooth & does not slip, or strain the motor, it does a damn gooood job!.....

STRONGBELT, as their name suggests, is a Heavy Industry German Brand that usually supplies the likes of Train manufacturers where serious levels of quality with no excuses on failure are expected from the product, as failure for such an item is serious & may result in death! STRONGBELT weave KEVLAR into their Pulley Belts, Kevlar is one of the strongest fibers known to man, its often added into materials to gain extra strength.... STRONGBELT have the best reputation in the Power Transmission Industry for NO stretching or snapping & we have high expectations from this quality item. 

These extra quality details in the production of our electronic motor drives, provides the maximum responsiveness achievable whilst maintaining a super smooth power delivery to the rider at all times. 

10cm of RED 4mm core 1036 Strand Silicon Coated Cable

Allow your Electric board to gain the maximum performance by fitting the very highest quality Electrical Cables & Connectors and let the power in your battery flood out as performance at the rear wheels!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn in production to produce to such a small amount of such a high quality cable, but finally TRAMPA has had what it wanted delivered & we can now supply you with Super high Quality Silicon Cables in RED or BLACK with co-orinating BLACK & WHITE TRAMPA logos to prove the quality & show off the kind of performance your board is capable of! :-)

TRAMPA's gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. The Blaff cables have enclosed in the Besilen insulated​ Silicon Outer sleeve, 1800 Highly flexible TOP QUALITY Copper strands in the center... BLAFF cable is used for the highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation (Trains, Trams, Planes) as they have a global reputation of incredible high standards.

TRAMPA Silicon cables solder perfectly into XT60 & XT90 connectors to give the perfect connection to your power source. A soldering service for a pair of cables is available though TRAMPA when you purchase the cables as pairs,

RED Silicon Casing with contrasting BLACK TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

10cm of BLACK 4mm core 1036 Strand Silicon Coated TRAMPA Logo'd Cable

Allow your Electric board to gain the maximum performance by only fitting the very highest quality Electrical Cables & Connectors to let the power in your battery flood out as performance at the wheel!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn to produce to such a small amount of cable at such a high quality standard, but finally TRAMPA has got what it wanted & has now taken delivery of its own Super high Quality Silicon Cables in RED & BLACK with contrasting Black & White TRAMPA logos to prove the quality & show off the kind of performance your board is harvesting! :-)

TRAMPA's Gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. BLAFF cable is used for highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation and the likes (Trains, Trams, Planes) as they have a global reputation of incredible high standards. 

Enclosed in the Besilen insulated​ Silicon Outer lies 1800 Highly flexible TOP QUALITY Copper strands in the center...

BLACK Silicon Casing with contrasting WHITE TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

XT90H-M connector - Male

On most TRAMPA electrical components, you’ll find AMASS XT90 connectors.  With a strong nylon plastic body & cylindrical brass contacts that comfortably fit 10-12 gauge wires, XT90 connectors are rated to handle 90 Amps continuous – but have been tested up to 270A!

Available as standard, or Anti-Spark - we recommend Anti-Spark for connections that are likely to be plugged/unplugged often.

5mm Cable Entry OPEN Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes

5mm Cable Entry Open Rubber Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes in Monster Box side panels for water proof assistance & Neat Cabling

5mm Rubber PLUG - Seals unused holes in Monster Box side panels when only using 1 Motor

This 5mm Round BUNG is used to seal off any 5mm un-used Motor Cable Holes in either the MONSTER Box, BEAST Box & Underboard BATTERY Box.

5mm ROUND BLIND Rubber Grommet for 5mm TRAMPA Silicone Cable

This 5mm Round Blind Grommet is used to seal off un used Motor Cable Entry Holes in the MONSTER Box, BEAST Box & Underboard BATTERY Box.

The 5mm Round Blind Grommet should also be fitted into all Battery Boxes which are using the Motor Cable entry holes as passing the cables through the 'OPEN' Grommet seals the hole best as possible & protects from the ingress of moisture & dust. 

To open the grommet to pass a cable through simply use a sharp Knife to press against the pre pressed slicing line & slice open the Rubber Membrane to allow you to push your cables through. Easy!

OVAL Rubber BLIND Grommet Cable Entry Hole - Fits in Monster Box side panels for water proof assistance & Neat Cabeling

This OVAL Rubber BLIND Grommet Cable Entry Blank is used to seal of Entry Holes in MONSTER Box, BEAST Box & Underboard Battery Tray which fits on the ORRSOM longboard. Simply push the Oval Grommet into position & your entery holes is sealed from moisture & dust.

If you need to push a cable through, use a sharp knife and carefully slice through the rubber membrane.

TRAMPA's own 160Kv 6364 2400w DC Brushless High Torque & High Speed Motor with 300mm TEMP Sensor cables Suitable for Single or TWIN Motor Drives!

TRAMPA's very own purpose made 136 KV Fully HALL & TEMPERATURE censored BLDC & FOC 6364 Out-Runner Motor provides 136 RPM per volt @ 1Nm. It has been CUSTOM MADE to handle HIGH VOLTAGE SET-UPS, i.e 26-44V using for example the VESC 4 & 6 speed controller. The Motor easily switches between FOC & BLDC modes running effortlessly in either mode.

The Motor houses Ultra high Temperature Copper & Ultra Strong High Temperature Neodymium Magnets. We designed an Extended & Heat treated 8mm Steel Axle shaft that's locked in position using 5 high precision Japanese Bearings, All screws & fixings used in its assembly are Marine Grade Stainless Steel, this motor easily out performs all & any competition on the market in so many aspects & its applicational use is almost endless!

Our special design allows you to to also fit  metal mesh filters to prevent the impregnation of larger particles ending in your motor! The front sided motor shield is equipped with twelve M4 treads, sitting on a 44mm diameter circle. The extra threads will allow you to mount the motor in the exact angle you wish, so that the three motor cables always sit in the perfect angle towards the mount or deck.

When handling and inspecting the motor the copper's appearance is almost dark red, suggesting very high quality & looks very special on first impression. 

TRAMPA's 118 kv Motor is fitted with an 38.5mm x 8mm (Extra long) Heat Treated Hardened Steel Motor Shaft, which is also fitted with a KEYWAY locator as standard! The extra length of the Axle allows us to fit Extra wide Motor Pulleys, meaning we fit a 15mm HTD 5M STRONGBELT as standard. A wider belt guarantees a much stronger power delivery. The end of the motor axle is supported with the use of a Bearing that is located in a Fixed housing, soaking up the strain of the powerful motor, & eliminating the possibility of bending the motor axle... Two 3x3x8mm KEYs lock the Axle shaft at both ends (1 into the Rotor & 1 into the Motor Pulley), eliminating all & any "Motor slip", thus providing maximum performance to the rider & gaining critical data for the VESC, ensuring all its high tech facilities can run as expected. TRAMPA's special motors are fitted with internal PCB Hall Sensors.

The Can Section of the motor has been Powder Coated White & finished with a very stylish Gold TRAMPA logo whilst the vented Aluminum end plates of the motor have been color coordinated Anodised Black. The Heavy Duty power cables use 4mm Gold Plated Bullet Connectors to connect to a power source. Typically for TRAMPA only Marine Grade Stainless Steel Fixings have been used in the assembly of this motor. & no parts will rust on you. This Motor can be connected to any of the Motor Pulleys in the TRAMPA product Range amongst others out there on the market...

62 Tooth Slave Pulley for URBAN Treads tyres - Perfect gearing for the little tyres :-)

The 62 Tooth Slave Pulley will give you the perfect final gearing when fitting the small URBAN TREADS TYRES :-) Fitting this Pulley will transform your Electric longboarding life completely :-)

This Pulley is fitted as standard to the amazing URBAN Carverboard & the new URBAN Longboard which are due out soon.... :-)

Custom 15mm wide Motor Pulley 13, 14 or 15 tooth

TRAMPA's 15mm wide 13-15 Tooth Motor Pulleys connect directly to the Motor Axle & are secured into position using a Magnetic Fixing Key & 4mm Locking Grub Screw.

These custom made Motor Pulley Wheels  fit 15mm wide STRONGBELTS, which should never stretch or break whilst at the same time providing a very smooth power delivery to the user - even from a standing start.

Choice of Aluminium or Black Steel. Aluminium Pulleys are perfect for those looking to save every gram possible on their board - Black Steel Pullys are heavier, but much harder wearing.

Changing your Motor Pulley &/or Drive pulley wheels will drastically change the performance of your ride... :-)

13 Tooth
Best performance for climbing steep inclines.

14 Tooth 
Best all-round performance

15 Tooth 
Best performance forreaching top speeds.

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x8mm

TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.

TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....

VESC 6 CNC Aluminum Heat Sink Silicone Sealed Housing

CNC T6 Aluminum box Houses the VESC 6 perfectly

Measures 75 x 70 x 18mm

12Fifties Extra wide Longboard Truck Motor Mount Truck Connector - T6 Aluminum BLACK

This simple but stylish T6 Aluminum 12FIFTIES Motor Mount Connector is specifically designed to work with TRAMPA's 12FIFTIES Extra wide Lonboard Trucks & is potentaillly compatible to fit with many similar Longboard Trucks too :-)

The Motor Mount Connector snuggly slides over the 12FIFTIES Truck Hanger & is secured tightened into position on the hanger with MARINE GRADE M6x10 grub screws.

The premium quality carbon Mounting Panel is held in position by being sandwiched between the Motor Mount Connector & the 12FIFTIES Truck Backplate. Compatible with Electric Motors with long or short Motor Axles - you’ll be able to fit pretty much any electric motor you wish but works best when accompanied with a TRAMPA motor for sure as we use a longer Motor Axle shaft whis this supported by a Motor Mount Axle shaft support housing...

Screwing through the 12FIFTIES Carbon Fibre Motor Mount panel & into an additional 12FIFTIES Backing plate holds everything in position for your motor to mount. These parts can be purchased as a kit on this link

TRAMPA 12Fifty Extra Wide Longboard Truck Clamping Disk

Extra Wide Longboard Truck Clamping Disk fits the Carbon Fiber Motor Mount to the New TRAMPA 12.5 Inch Wide 50º Longboard Trucks

Motor Axle Support for Spring Truck Motor Mounts UNIVERSAL

This part ensures your motor is supported and the belt is running straight - two very important jobs for a smooth, fast and reliable board.

Motors with longer axles, like TRAMPA’s own, will fit perfectly into the housed bearing within, supporting the axle rotation, ensuring there is no ‘give’ in the axle, where the belt could potentially slip off at high speeds.

Fitting onto Channel Truck Motor Mounts this Motor Axle Support will work with any of the 6-9inch tyres in the TRAMPA range.

M4 x 35mm Socket Capped Allen-Key Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 35mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the TRAMPA HYPA HUBS. The socket capped head of the Bolt fits neatly into the Bolt housing of the HYPA HUB marrying into the M4 nut located in the housing on the other side of the hub.

Weighing just 3 grams each these bolts are very lightweight. They look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You will need a 3mm Allen Key to tighten & loosen the Nuts & Bolts from the hub. Ensure all your Nuts & Bolts are tight before riding!

M5 x 16mm Hex Head Bolt ISO 4017 Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 25mm Dome Headed TORX Bolt - Marine Grade Stainless steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 25mm Socket Capped Head TORX Bolt ISO 4762 Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 18mm TORX Socket Capped Head Bolt ISO 4762 Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 16mm TORX Socket Capped Head Bolt ISO 4762 Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 20mm Socket Capped Head TORX Bolt ISO 4762 Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 4mm Grub Screw M4 x 4mm Motor Pulley Grub Screw - Connects the Motor Pulley onto the Motor Axle Shaft

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M6 x 10mm Grub Screw Marine Grade Stainless Steel - Locks Motor Mount to Hanger for Longboard Trucks

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts

Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or  8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!

3/8ths Nut - Marine Grade Stainless steel Nylock HALF nut W3/8 - 24T UNF

This very special Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore reducing weight in the Truck also! A few Grams here & a few grams there soon adds up to quite alot & that makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area...

This very special 3/8^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W3/8_^ths - 24T - UNF. This Nut is used to hold the wheels onto the axles of the 9.525mm (3/8ths of Inch or otherwise referred to as 10mm) SKATE TRUCKS & also the Spring Trucks fitted with TITANIUM axles. This Nut is also used to hold the KINGPIN in position on all Skate Trucks. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 14mm or 9/16^ths of an Inch spanner to tighten the Nut onto the Axle or Kingpin, do not overtighten the nut, allow the wheel to spin freely but not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

 - Fits to 9.525mm (3/8ths) Axles & Skate Truck Kingpins

3/8ths Nut - Marine Grade Stainless steel Nylock HALF nut W3/8 - 24T UNF

This very special Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore reducing weight in the Truck also! A few Grams here & a few grams there soon adds up to quite alot & that makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area...

This very special 3/8^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W3/8_^ths - 24T - UNF. This Nut is used to hold the wheels onto the axles of the 9.525mm (3/8ths of Inch or otherwise referred to as 10mm) SKATE TRUCKS & also the Spring Trucks fitted with TITANIUM axles. This Nut is also used to hold the KINGPIN in position on all Skate Trucks. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 14mm or 9/16^ths of an Inch spanner to tighten the Nut onto the Axle or Kingpin, do not overtighten the nut, allow the wheel to spin freely but not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

 - Fits to 9.525mm (3/8ths) Axles & Skate Truck Kingpins

M4 8x8mm Nikel plated Flush fitting Threaded Insert Nut is Screwed into the ORRSOM longboard deck & used for fixing the Underboard Battery Tray to the Deck

This M4 8m x 8mm RAMPA Muffen or Insert nut will allow you to secure M4 Bolts to your deck without the need of using often unsightly or protruding nut on the other side leaving a neat clean smooth finish to your assembly....

We use these M4 RAMPA Nuts to secure the UNDERBOARD Battery Tray to the underside of all of the Electric ORRSOM Boards...

To make the hole to accept the fitting the nut, you will need to measure accurately so first make a pilot hole using a 2/3mm drill bit. Then specifically using a 5mm Steel drill bit, carefully drill the larger sized hole remembering to drill at 90º to the surface. If you do not Drill 90º to the surface your RAMPA Nuts will not fit flush...

Once you have made the 5mm holes, use a 4mm Allen Key to screw the RAMPA nut into the deck. Be careful when screwing in, you need to add a little bit of force to make it bite into the surrounding material, but not too much force as you do not wish to push through anything.... Turning the M4 Allen Key may be tough as when screwing the nut into the deck as it will literally cutting a thread into the surrounding material of the deck as you do...  It may help secure the RAMPA nuts even better if you add a tiny squirt of Glue as you tighten up the last few turns...

M4 x 20mm Hex Spacer - 5 Spoke Wheels to Slave Wheels on OBD & ORRSOM Boards

Used for connecting Slave Pulleys to Hubs using a 12-FIFTIES Motor Mount. 

x5 Required for HYPA hubs
x6 Required for SUPERSTAR / MEGASTAR hubs

PRECISION Shim spacer - STAINLESS STEEL - Bridges tiny gaps on axles - 9.525 x 13.525 x 1mm

This tiny STEEL Shim Spacer is precision made to give maximum performance! It is used to hold the bearings in the perfect position & also to bridge tiny gaps on the axles, ensuring an accurate fit with NO rattles!

The Shim spacer slips onto the axle fitting either side of the Bearings when the wheel is being fitted onto 9.525mm Axles.

This tiny spacer positions the wheel perfectly on the axle, holding the Bearing in the best possible place to help achieve maximum spin rate for the wheel. Its little parts like these that suffer the most amount of abuse, especially when they are used in the harsh conditions that they are. Check from time to time they are in good order & possibly replacing them every now & then this good proactice will ensure your board stays in tip-top condition, always!

M4 Socket Capped Washer Anodised

M4 Caphead Washer great way to pimp and customise your board in 10 differnt colours used in conjunction with all our M4 Capheaded bolts great way to finish off your board/project

12FiFties Longboard Hanger 310mm with 9.525mm SOLID Steel Axle

TRAMPA’s amazing 12FiFties Extra Wide Longboard Trucks are amazingly responsive, strong & adaptable.

Designed to be used in conjunction with TRAMPA's ORRSOM longboard deck, they provide a market leading variety of customisation options only dreamt about with your standard longboard.

If you love building your own longboards, be it electric powered or gravity fed, this could be the new truck for you!

12FiFties Hangers measure 12.5 inches wide,  the extra width providing superior stability at high speed, as well as the clearance for adding larger wheels. Compatible wheel sizes range from 83mm Trampa stickies - for ultimate tarmac cruising, all the way through the range up to 8'' pneumatic tyres - providing the most unrivalled off road experience.

Trampa have achieved this by factory fitting 9.525mm hardened steel axles, then offering different bearing alternatives to suit; Stickies R6-2RS, Skate 28x9.525mm or  R6001RS 28x12mm with a reducer sleeve.

This is the most versitile longboard truck for any terrain type! 

Designed with our standardised skate kingpin (9.4 x 50mm) & mounted at 50º angle to the baseplate for optimum steering responsiveness. 

Baseplates are available in 10 different anodonised colours for unrivalled customisation! 

Precision CNC’d from solid blocks of T6 heat-treated Aluminium, 12FiFties HANGERS are remarkably strong, able to withstand the forces, bumps or crashes they’ll inevitably recieve if ridden properly. Aswell as looking the part with a polished silver finish!

The hanger body has been CNC'nd along the complete length to 19.5mm x 19.5mm, and then grooved to allow the electric motor mount to be preicisely clamped to the truck. The mount itself consists of a simple laser-cut carbon panel and a CNC'd 12FiFties clamping ring available in the motor mounts section of the website.

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

Hypa Hub 3.75x 2 Inch - Matt Black

TRAMPA's 6 spoke HYPA Hub is by far the lightest & weight for weight compared, the strongest 3.75-inch hub on the market today!

The HYPA hubs 6 spoke design is technically advanced & is manufactured using original Du-Pont materials & the very latest in precision injection molding machinery - No quality expense is spared! This deluxe combination of technical design, top quality machinery & original genuine materials, creates a product that is far superior to all of our competitions, resulting in performance that is well beyond normal expectations. This extra performance means the TRAMPA HYPA hub can handle much higher than recommended tyre inflation pressures, generating substantially higher than normal roll speeds. Back in the day during testing, our crash test dummies (i mean the Team riders) commonly rode with these hubs well above 80psi & beyond.... 

The HYPA hubs are held together using only the best Marine Grade (A4) Stainless steel Nuts & Bolts so they definitely wont rust on you (EVER) & are therefore perfect for bad conditions. All the Bolts used by TRAMPA have been dipped in a special Blue Locking Paste & all the Nuts are fitted with the world renowned Nylon "Nylock" Nut locking System, all these no expense spared small details ensure you get the absolute best hub possible!

HYPA hubs are available in loads of different colours & surface finishes, all of which are TRAMPA embossed between the spokes proving the top quality! Do not buy imitations as they will not perform the same!  TRAMPA’s own high class Steel Bearings, (Genuine  ABEC 5 rated Bearings) push perfectly into the HYPA hub bearing housing, guaranteeing the fastest spin rate to the wheel possible. Use either Bearing reducer sleeves into 12mm Bearings or use TRAMPA's 10mm Bearings to fit the HYPA hubs onto smaller sized skate axles. HYPA hubs are compatible with all known 8-inch tyres currently on the market including MBS & Scrub. Put quite simply – HYPA hubs are by the Best!

Along with many other applications that these wheels will fit too, the HYPA hub will fit and accept ALL the other brands of mountain boards on the market including MBS, SCRUB & KHEO, so when you are looking for an upgrade to your ride you know where too look! Basically the HYPA Hub will fit to anything that uses a Imperial 7/16ths (9.52mm) or 12mm bearings to fit onto the axle. If you already have your own 12mm bearings there are conversion spacers available to convert your 12mm bearings to work on the 7/16ths Imperial (9.52mm) skate axles and a different size spacer to convert them to fit 10mm (metric) scooter axles (see associated parts for details).

Bearings are supplied at a discounted price when purchased with hubs...

Rim Diameter 3.75 Inch
Rim Width      2 Inch or 50mm
​Fits all Tyres with 3.75 Inch rim inflating up to 8 inch in Diameter

URBAN TREADS 6 Inch Tyre measures 3.75x 1.75x 6.5 Inch or 165x 45mm with 3.75 inch Rim & fits all 3.75 inch Hubs - BLACK

Produced at the INNOVA Factory, TRAMPA's own 3.75x 2x 6.5 Inch or 165x 45mm Super Low profile URBAN TREADS tyres have been specifically designed to fit TRAMPA's incredibly strong & sexy range of 3.75 Inch hubs. 

We wanted to radically change the rough ride experience of that when riding with regular style longboard wheels, even the super-soft GUMMIES tyres can feel harsh when riding on not so smooth surfaces such as when riding in Urban/City environments.... We all know the pavements & roads are far from a perfect surface so much so that sometimes its almost impossible to ride regular Longboard wheels, some of the pot holes around me are terrible but with these URBAN TREADS tyres fitted you can smash through all the imperfections whilst still enjoying that small wheel fast turn feel... 

TRAMPA's 6.5 Inch URBAN TREADS tyres are arguably the Premium Tyre choice when it comes to requiring lots of grip from Small sized wheels. Produced with whats known as a 'High TPI casing' the rubber compound used is 'super soft & very Grippy'. TPI means Threads Per inch & the URBAN TREADS tyre, being premium, uses thousands of very fine threads per Inch in its construction to stitch between the 'outer lightweight nylon Rims', the length of the threads in turn gives the wide construction shape to the tyre... having a High TPI means the tyre's construction is incredibly strong whilst still very supple, like a posh bicycle tyre. 

Having a High TPI & using hefty amounts of thick Motorcycle rubber means not only is the construction of the tyre incredibly strong but it will also wear incredibly well too. This extra strength in turn allows the tyre to be run at both, incredibly low tyre pressure or should the circumstances require (such as a skate park where you need to pump hard) inflated to being incredibly hard, the URBAN TREADS tyres can easily handle our factory set limit of 65psi. We have herd of some of the crazy Lab Rats we use (i mean TRAMPA team riders) are inflating URBAN TREADS over 100psi (i dont think their pump will allow them to get any more air in haha) & with currently no problems to report... But for sure, if one pop's at 100psi it will certainly make one hell of a noise!! BANG!!​ haha! :-)

Riding on such a small sized tyre gives the most radical performance change to literally every board in the TRAMPA range. There is no doubt the tyre was developed specifically for the URBAN CARVER BOARD & more in particular the ELECTRIC URBAN CARVE BOARD where both products use a smaller deck & the smaller sized Mini Spring Trucks system,  the smaller board needed a slightly smaller tyre than that of the full sized 8 inch ATB decks to compliment the overall product size, so in true TRAMPA style we made the URBAN TREADS Tyre special for that application but since then we have found over these last cold wet winter months that the 6.5 inch URBAN TREADS tyres have also become the choice tyre for Mountainboards who are maintaining their riding skills in the out of season period by riding in indoor Parks or Tracks, just ask Sonnie - TRAMPA Pro Team rider, who has literally not stopped riding indoor skate parks to retain his fitness through the winter since the release of these new tyres...

TRAMPA's Electric boards have amazing performance with a top speed of over 60kmph achievable on all models. When your hitting high speeds like this you need good tyres on your board. Thankfully the URBAN CARVE range of decks are fitted with super sexy 6.5 inch URBAN TREADS Tyres connected to 62 Tooth Pulleys as standard. The reinforced, low profiled, wide center beaded with intelligently designed jagged edge around the side can be run on low inflation pressure which gives enough grip to cut muddy corners or nip down hard packed off road tracks no problem, but can also handle the super inflation for straight line flat out speed. If you wish to ride full speed we 1stly suggest you turn the SPRING ADJUSTERS clockwise to tighten the steering resistance, pre-loading more tension into your springs before you wish to hit high speeds will prevent potential wobble, and if you re beginning to feel a bit of wobble, then you should move the springs to the outside position before attempting to go any faster. If you still feel speed wobble when the springs are in the outside position, then you should then further add the TRAMPA DAMPA's to add even more steering resistance to enable you to be able to go even faster :-)

The Urban Tread tyre doesn't only handle high speeds easily but riding around town where you are likely to be bashing up & down curbs & dealing with cracks in the road or potholes, then you should be riding at much lower inflation pressures. The lower pressure gives so much comfort on the rougher stuff but of course does increase Drag making it harder for your batteries to perform well...