Home»Clearance Corner»EMB 22 - 16ply HolyPro Deck, Infinity Trucks, HYPA Wheels, 16a Beast TWIN VESC MK1 URBAN Motor Mounts 118Kv Motors - No Bindings

TRAMPA Ratchet & Camlock Style Footstrap & Ladder

TRAMPA Ratchet style foot-straps are the strongest & most Sturdy bindings on the market! Ergonomically designed to ensure a comfy fit, TRAMPA Bindings will keep your feet, locked into the perfect position, enabling your board to be as responsive as it should.? The L Brackets are connected to the footstraps using Marine Grade Stainless Steel Extra Wide DOME HEADED BOLTS. These will not "Pull through" or interfere with the comfort on the side of your foot what so ever.... 

Our amazing foot-straps have a special "SLOT" on the top of the plastic strap to allow the "90º Hook" (found on the base of the Ratchet or Camlock Buckle), to locate into.  This special slot locks the Buckle perfectly into place, eliminating any potential movement. A special Marine Grade Stainless Steel STAR NUT pushes into the foam from the underside of the strap & a 8mm countersunk bolt tightens the buckle firmly into the strap. Replacement foot-straps are sold as pairs & will fit both RATCHET & CAMLOCK Buckles. Ladder straps are sold separately.

Custom TRAMPA L-Bracket

TRAMPA L Brackets are made using 5mm thick Extruded T6 Aluminum - They should never fail on you. TRAMPA L-Brackets will fit to all of  the binding options TRAMPA has to offer.

Once the expensive material has been forced through the extrusion die, the continuous L shape that comes out the other side is then 'Punched' into the resulting profile that you can see. Extruding aluminum gives the metal the strongest molecular structure possible. Once punched its then sent off to be 'Heat Treated' then high quality polished to take off sharp or un-wanted edges and a nice shiny surface finish that is perfect for Anodising or Powder coating. All of TRAMPA's L Brackets come with a colour co-ordinating TRAMPA logo. 

With 3 different mounting positions on the upright side of the L-Bracket its possible to customise the mounting position of the footstraps in the Mounting points of the L-Bracket & with 4 mounting positions in the Base of the L-Bracket you can customise the position of the L bracket on the deck suitable to your ride stance or leg length or just to your liking so with some trials & errors its possible to find the absolute perfect positioning for your feet & footwear when riding. Its important to have comfortable feet when riding....

TRAMPA's L-Brackets fit to all TRAMPA foot straps as well as most other brands foot straps & is therefore compatible to fit to both MBS & Scrub boards. Ensure all your nuts and bolts are tight before riding!

M5x20mm Extra Wide Dome Head Bolts with M5 nuts & M5 Washers connect the L Bracket to the TRAMPA Binding Foot Straps. 

M6x25mm Countersunk bolts with M6 nuts & M6 Washers push through the deck from the underside & hold the L Bracket to the top side of the TRAMPA deck.

CUSTOM Ratchet Buckle

TRAMPA's RATCHET BUCKLE connects to FOOTSTRAPS & to HEEL STRAPA. The Ratchet Buckles are a fundamental component part of the BINDINGS, the RATCHET STYLE BINDINGS will not function without them. 

Ratchet Buckles are most commonly used by Mountain Board Riders looking for the tightest connection to the Deck. By simply lifting the ratchet lever up & down feeds the Ladder Strap into the Ratchet Buckle gradually tightening as it goes. You can tighten the strap as much as you comfortably like the bindings to be. To undo the Ratchet Buckle simple apply some pressure to the Release Clip and the straps should simply pull apart.

The Base of the RATCHET BUCKLE has a "Special Hook" The Hook is used to slip into a special slot, anchoring the Ratchet into the footstrap, eliminating any movement in its mounting. This locking into position ensures maximum control over your board through your bindings at all times. A Quick Release Clip, using an extra long lever makes opening the bindings really easy to do, whilst a range of colour coordinating surface protection (colour) options allows you to match up in colour to all of the TRAMPA products on sale. Use an M5x8mm Countersunk Bolt & special Marine Grade Stainless steel STAR NUT to fix the Ratchet Buckle into the Foot Strap. Ensure your nuts & bolts are tight before you ride!

1x 9 Inch squares of Top Quality Jessup Grip tape

Mega Grippy & really easy to apply. Ensure the decks surface is clean & dry before application. Easy to custom shape, simply draw your shape on the back & cut out with Scissors or sharp knife. Remember to use a ruler for clean edges. Watch your fingers when slicing, please ask an adult to make this work if you are under 16 & please remember, when you draw on the back of the grip tape remember its a mirror image so do everything in switch! Use a template for best results... :-)

10cm of RED 4mm core 1036 Strand Silicon Coated Cable

Allow your Electric board to gain the maximum performance by fitting the very highest quality Electrical Cables & Connectors and let the power in your battery flood out as performance at the rear wheels!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn in production to produce to such a small amount of such a high quality cable, but finally TRAMPA has had what it wanted delivered & we can now supply you with Super high Quality Silicon Cables in RED or BLACK with co-orinating BLACK & WHITE TRAMPA logos to prove the quality & show off the kind of performance your board is capable of! :-)

TRAMPA's gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. The Blaff cables have enclosed in the Besilen insulated​ Silicon Outer sleeve, 1800 Highly flexible TOP QUALITY Copper strands in the center... BLAFF cable is used for the highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation (Trains, Trams, Planes) as they have a global reputation of incredible high standards.

TRAMPA Silicon cables solder perfectly into XT60 & XT90 connectors to give the perfect connection to your power source. A soldering service for a pair of cables is available though TRAMPA when you purchase the cables as pairs,

RED Silicon Casing with contrasting BLACK TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

10cm of BLACK 4mm core 1036 Strand Silicon Coated TRAMPA Logo'd Cable

Allow your Electric board to gain the maximum performance by only fitting the very highest quality Electrical Cables & Connectors to let the power in your battery flood out as performance at the wheel!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn to produce to such a small amount of cable at such a high quality standard, but finally TRAMPA has got what it wanted & has now taken delivery of its own Super high Quality Silicon Cables in RED & BLACK with contrasting Black & White TRAMPA logos to prove the quality & show off the kind of performance your board is harvesting! :-)

TRAMPA's Gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. BLAFF cable is used for highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation and the likes (Trains, Trams, Planes) as they have a global reputation of incredible high standards. 

Enclosed in the Besilen insulated​ Silicon Outer lies 1800 Highly flexible TOP QUALITY Copper strands in the center...

BLACK Silicon Casing with contrasting WHITE TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

Cable Harness for wiring Power Switches to VESCs

Harness allows connection between VESC 6 MkIII or newer and on/off switch.

XT90H-M connector - Male

On most TRAMPA electrical components, you’ll find AMASS XT90 connectors.  With a strong nylon plastic body & cylindrical brass contacts that comfortably fit 10-12 gauge wires, XT90 connectors are rated to handle 90 Amps continuous – but have been tested up to 270A!

Available as standard, or Anti-Spark - we recommend Anti-Spark for connections that are likely to be plugged/unplugged often.

TRAMPA Switch with 5V LED QUALA-T logo & 16mm Stainless Steel Fixing Nut

The TRAMPA 'QUALA-T" stamped Power Switch is a sexy little switch & to co-ordinate with the huge array of anodised & painted colours that TRAMPA offers to tie into all the other kit we offer is available in 6 different colours - RED, BLUE, YELLOW, GREEN, WHITE, PINKY/PURPLE

Which means no more loop keys!
All TRAMPA Mountainoboards Boards fitted with VESC 6 MKIII & any later models can now be fitted with power buttons for easy powering on/off and a much sleeker looking board!

You will need a Power Switch Cable harnesses to plug in

The QUALA-T Switch is Non-latching & limited to a Max voltage of 5v 

5mm ROUND BLIND Rubber Grommet for 5mm TRAMPA Silicone Cable

This 5mm Round Blind Grommet is used to seal off un used Motor Cable Entry Holes in the MONSTER Box, BEAST Box & Underboard BATTERY Box.

The 5mm Round Blind Grommet should also be fitted into all Battery Boxes which are using the Motor Cable entry holes as passing the cables through the 'OPEN' Grommet seals the hole best as possible & protects from the ingress of moisture & dust. 

To open the grommet to pass a cable through simply use a sharp Knife to press against the pre pressed slicing line & slice open the Rubber Membrane to allow you to push your cables through. Easy!

5mm Cable Entry OPEN Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes

5mm Cable Entry Open Rubber Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes in Monster Box side panels for water proof assistance & Neat Cabling

OVAL Rubber BLIND Grommet Cable Entry Hole - Fits in Monster Box side panels for water proof assistance & Neat Cabeling

This OVAL Rubber BLIND Grommet Cable Entry Blank is used to seal of Entry Holes in MONSTER Box, BEAST Box & Underboard Battery Tray which fits on the ORRSOM longboard. Simply push the Oval Grommet into position & your entery holes is sealed from moisture & dust.

If you need to push a cable through, use a sharp knife and carefully slice through the rubber membrane.

16A BIGGEST BEAST Box kit inc Mounting Panel to fit 2x VESC 6 with LED Screen & NRF Housing 16000 mAh cell packs!!

TRAMPA’s Beast Boxes come in three different sizes;

STANDARD - fitting up to 6200mAH Batteries

BIGGER - fitting up to 12,000mAH Batteries

BIGGEST - fitting up to 16,000mAH Batteries.

Boards with single motors could go for any of the Beast Boxes - dependant on the desired range / weight of the finished board.

Boards with TWIN Motors will need to go for the BIGGEST BOX, in order to accommodate room for the extra VESC that needs to sit inside.

Able to fit onto any TRAMPA board with Spring Trucks, BEAST BOXES made from 2mm thick 3k Twill Carbon Fiber & are precision CNC machined & internally grooved to give perfectly fitted joins, making the Beast Box pretty much water proof. Heat shrinking your joins & adding a touch of silicon at the end of the assembly will for sure seal the box to be tight from water!

The beast box comes with a top mounted LCD Battery Indicator, so guessing range is no longer an issue!

Assembling the box has been described as “fiddly but fun”. It’s a tight fit when using the biggest batteries for each box, so keep that in mind while assembling. The less room the batteries have to bounce around inside the box the better - especially over rougher terrain!

Stainless steel Countersunk bolts harmoniously connect into both the base & the lid of the box, screwing neatly & tightly into HEX spacers... as the lid is tightened down, you'll get a satisfying click of confidence that everything has dropped into place perfectly, as the panels slips into the groove and the gaps are no longer visible!

Battery Box Width - 110m
Battery Box Length - 200mm
Everything fits Internally!

VESC 6 CNC Aluminum Heat Sink Silicone Sealed Housing

CNC T6 Aluminum box Houses the VESC 6 perfectly

Measures 75 x 70 x 18mm

TRAMPA's own 160Kv 6364 2400w DC Brushless High Torque & High Speed Motor with 300mm TEMP Sensor cables Suitable for Single or TWIN Motor Drives!

TRAMPA's very own purpose made 136 KV Fully HALL & TEMPERATURE censored BLDC & FOC 6364 Out-Runner Motor provides 136 RPM per volt @ 1Nm. It has been CUSTOM MADE to handle HIGH VOLTAGE SET-UPS, i.e 26-44V using for example the VESC 4 & 6 speed controller. The Motor easily switches between FOC & BLDC modes running effortlessly in either mode.

The Motor houses Ultra high Temperature Copper & Ultra Strong High Temperature Neodymium Magnets. We designed an Extended & Heat treated 8mm Steel Axle shaft that's locked in position using 5 high precision Japanese Bearings, All screws & fixings used in its assembly are Marine Grade Stainless Steel, this motor easily out performs all & any competition on the market in so many aspects & its applicational use is almost endless!

Our special design allows you to to also fit  metal mesh filters to prevent the impregnation of larger particles ending in your motor! The front sided motor shield is equipped with twelve M4 treads, sitting on a 44mm diameter circle. The extra threads will allow you to mount the motor in the exact angle you wish, so that the three motor cables always sit in the perfect angle towards the mount or deck.

When handling and inspecting the motor the copper's appearance is almost dark red, suggesting very high quality & looks very special on first impression. 

TRAMPA's 118 kv Motor is fitted with an 38.5mm x 8mm (Extra long) Heat Treated Hardened Steel Motor Shaft, which is also fitted with a KEYWAY locator as standard! The extra length of the Axle allows us to fit Extra wide Motor Pulleys, meaning we fit a 15mm HTD 5M STRONGBELT as standard. A wider belt guarantees a much stronger power delivery. The end of the motor axle is supported with the use of a Bearing that is located in a Fixed housing, soaking up the strain of the powerful motor, & eliminating the possibility of bending the motor axle... Two 3x3x8mm KEYs lock the Axle shaft at both ends (1 into the Rotor & 1 into the Motor Pulley), eliminating all & any "Motor slip", thus providing maximum performance to the rider & gaining critical data for the VESC, ensuring all its high tech facilities can run as expected. TRAMPA's special motors are fitted with internal PCB Hall Sensors.

The Can Section of the motor has been Powder Coated White & finished with a very stylish Gold TRAMPA logo whilst the vented Aluminum end plates of the motor have been color coordinated Anodised Black. The Heavy Duty power cables use 4mm Gold Plated Bullet Connectors to connect to a power source. Typically for TRAMPA only Marine Grade Stainless Steel Fixings have been used in the assembly of this motor. & no parts will rust on you. This Motor can be connected to any of the Motor Pulleys in the TRAMPA product Range amongst others out there on the market...

Original Urban Carver Truck Motor mounting panel Connector - T6 Aluminum CNC'd to fit Regular or Goofy Motor mount Panels

Made from top quality T6 Heat-Treated Aluminum, this motor mount connector slides snuggly over TRAMPA’s ATB & MINI SPRING Trucks and securely holds the Drive Train in place - no matter what terrains and sharp turns you throw at it. 

Fits to Urban Mountain board & Urban Carveboard Motor Mounts. 

Held in place with 2x M8x16mm GRUB screws

Motor Axle Support for Spring Truck Motor Mounts UNIVERSAL

This part ensures your motor is supported and the belt is running straight - two very important jobs for a smooth, fast and reliable board.

Motors with longer axles, like TRAMPA’s own, will fit perfectly into the housed bearing within, supporting the axle rotation, ensuring there is no ‘give’ in the axle, where the belt could potentially slip off at high speeds.

Fitting onto Channel Truck Motor Mounts this Motor Axle Support will work with any of the 6-9inch tyres in the TRAMPA range.

M4 x 10mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 35mm TORX Countersunk Bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 25mmTORX Countersunk Bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M5 x 8mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-Ratchet Bindings

-Camlock Bindings

-Heelstraps

-3d Sprung Steel Flex Brake

M6 x 30mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

- 6-8s Battery Box

- 8-10s Battery Box

-Beast Boxes

M6 x 25mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-Bindings

M5 x 12mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-Ratchet Bindings

-Camlock Bindings

-Heelstraps

M5 x 20mm EXTRA WIDE Dome head Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

This Bolt is DOME HEADED, meaning that when screwed into position it sits low & neatly over the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-Bindings

M5 x 25mm HEX Head SHANKED Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 35mm Socket Capped Allen-Key Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 35mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the TRAMPA HYPA HUBS. The socket capped head of the Bolt fits neatly into the Bolt housing of the HYPA HUB marrying into the M4 nut located in the housing on the other side of the hub.

Weighing just 3 grams each these bolts are very lightweight. They look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You will need a 3mm Allen Key to tighten & loosen the Nuts & Bolts from the hub. Ensure all your Nuts & Bolts are tight before riding!

M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts

Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or  8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!

M5 Nut - Marine Grade Stainless steel Nylock Nut - Fixes to Trucks & Bindings

Introducing TRAMPA's M5 (5mm Thread) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M5 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M5 Bolts that hold the TRUCKS to the DECK for all  Decks & also for the Dome Head Bolts connecting the L BRACKETS to the Bindings. Use an 8mm spanner or Ratchet Drive to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M5 Nut - Marine Grade Stainless steel Nylock Nut - Fixes to Trucks & Bindings

Introducing TRAMPA's M5 (5mm Thread) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M5 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M5 Bolts that hold the TRUCKS to the DECK for all  Decks & also for the Dome Head Bolts connecting the L BRACKETS to the Bindings. Use an 8mm spanner or Ratchet Drive to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

7/16ths Nut - Marine Grade Stainless steel Nylock Axle HALF nut (W7/16-20T UNF) - Fits to 12mm Axles

This very special 7/16_^ths of an inch Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut.. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore further reducing weight in the Truck! A few Grams here & a few grams there soon adds up & makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area, where a few grams makes all the difference...

This very special 3/8_^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W7/16 - 20T - UNF. This Nut is used to hold the wheels onto the axles of the Spring Trucks fitted with 12mm axles. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 16mm or 5/8th_^ths of an Inch spanner to tighten / loosen the Nut onto the Axle or Kingpin. Do not overtighten the nut & make sure the wheel can spin freely but does not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

M5 Star Nut - Fixes Ratchet & Camlock to footstraps - Marine Grade Stainless steel

TRAMPA's M5 STAR NUT fastener is used for fixing the RATCHET or CAMLOCK to the BINDING FOOTSTRAP. This nut is made from Marine Grade Stainless Steel and is Guaranteed never to rust on you! 

The cerated edges of the nut cut into the foam of the footstrap & create a solid fix into the bindings. The nut pushes into the foam of the Binding holding the Ratchet in the perfect position. As a tip, use an axle spacer to push the STAR NUT into position within the foot strap. It needs a good push into position to ensure it doesnt rip free from the fixing....   Use M5 x 8mm countersunk bolt to fix Ratchet or Camlock into the Footstrap   

M4 x 80mm Aluminium Threaded Spacer Nut Used for assembling the BEAST Battery Boxes

Used for assembling the BEAST BATTERY BOX.

x7 Required per box

Wheel support spacer for all TRAMPA Wheels on 12mm ATB Axles - CNC precision 12mm x 16mm x 18.2mm - CUSTOM

This special Spacer measures 12mm (id) x 16mm (od) x 18.2mm (long) & has 2 uses!. It is firstly known as the Bearing Support Spacer as this Spacer fits between the Bearings of a 6 Spoked HYPA Hub, (when mounting the HYPA wheel onto 12mm Axles) & secondly it is also known as the AXLE SUPPORT SPACER as this spacer is also used to position any of the TRAMPA wheels in the perfect position onto the axles of 12mm TRAMPA Spring trucks....

TRAMPA spacers are produced as one long tube. The Tube is Heat Treated to gain extra strength & is then Bead Polished to give the metal extra surface protection & a shiny best appearance. The tube is then cut to the exact length for precision mounting. 

CUSTOM Spring Truck Baseplate - Extruded T6 Aluminum Anodised & CNC precision Milled

The  INFINITY Baseplate will fit to all of the TRAMPA Spring Truck Hangers but is designed specifically to work in conjunction with the Mini Spring Hanger as it houses a NEW Dual Spring Adjuster position! When the Springs are moved to the new inside position, the new location allows the rider to turn the board very very easily, making it perfect for fast carve riding on all kinds of terrain. You can see the new & growing TRAMPA STREET CARVER range of products here...

The  INFINITY Baseplate is, as its name suggests, designed & built to last forever! Aircraft grade 6061 Aluminum is forced through a Die to create our re-enforced extruded profile. Extruding Aluminum ensures consistent high quality strength. Once Extruded the Baseplate is T6 Heat Treated. Heat treating extruded aluminum fuses the molecules even closer together making it as strong as possible, enabling the INFINITY Baseplate to easily cope with the extreme stresses of all types of off road boarding.

Once Heat Treated, the profile has its fixing holes punched into position & then its Bead Polished in preparation to be Anodised Silver. Once the colour has dried, the Baseplate is then returned to the factory for the precision CNC Machine to accurately mill the Kingpin holes, giving the exact precision required for constructing the Truck.

16 inch wide CNC finished INFINITY Motor Mount Hanger with 12mm SOLID Steel Axles - connects with all Spring Truck Baseplates & Mountainboard Motor Mounts

The INFINITY HANGER is the strongest SPRING TRUCK Hanger in the TRAMPA product range! To ensure the maximum strength possible the hanger body is made from FORGED ALUMINUM and is one solid piece - with no weight saving holes !

These Hangers have been CNC'd for precise and secure motor mount attachment.

The Axles have also been HEAT TREATED. Heat treating steel makes it substantially stronger & more resistant to impact. 12mm Solid Steel Axles are slightly heavier than alternatives displayed on the TRAMPA website, but they are by far the strongest Axles in the TRAMPA range. Marine Grade Stinless steel GRUB SCREWS help keep the Axles locked into the correct place within the Hanger.

A CNC milling machine is used & guarantee's to drill the Kingpin Holes accurately. Ensuring the Kingpin Holes are accurately placed guarantees the best performance to the rider, as well making the truck easy to assembly & service. The Infinity Hanger is EDP painted MATT BLACK for metal protection & colour coordinating good looks before the CNC work is carried out.

The Infinity Hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the board has a center wheel width of 14 Inches. The Infinity hanger will fit to all TRAMPA Baseplates.

TRAMPA's Infinity Hanger uses 2x 18.2mm x 12mm SPACERS (1 either side). The spacer slips onto the axles, leaving the perfect space to mount the TRAMPA wheels accurately. Use the 7/16ths of an inch Axle Nuts to lock the wheels into place on the axle.

Kingpin bushings push into the Kingpin holes, in both the Hanger & the Baseplate. When all the bushings are in position, push the Baseplate over the Hanger and into position so that all the Kingpin holes line up. When this is the case you will be able to push the kingpin, from the front to the truck to the back, through the holes in the assembly, connecting them all together. Remember to add the washer onto the kingpin before sliding into the assembly.

Custom Kingpin for Spring Trucks - M8x80mm Nikle Plated, Stainless Steel or TITANIUM

This 'M8 x 80mm Spring Truck Kingpin' is used to connect the Hanger & the Baseplate on any of TRAMPA's Spring Trucks.

Using high quality metals & sizing down to a 8mm Kingpin, we have managed to save loads of weight whilst retaining all the strength necessary for the job!

This M8 x 80mm Kingpin uses an 8mm Washer to support the busing from the outside & a 6mm washer to protect the bushing on the inside side & connects into an M6 Nut. You'll need a 4mm Allen key to hold the Kingpin & a 10mm spanner to tighten/loosen your M6 Kingpin Nut.

This Kingpin pushes through plastic bushings before being placed into position in the Truck System. The Plastic bushings allow the metal parts (Hanger & Baseplate) to move freely inside each other without allowing the metal parts to touch or wear out.

The plastic bushings will wear out over time & use & will eventually perish & need replacing. SO, make sure your Bushings are always in good working order after riding riding or when upgrading your Kingpin, it might be time to replace them too due to the unavoidable wear & tear of moving mountainboard parts.

King Pin Bushings have different thickness bases & fit into all Spring Trucks

The 2mm Kingpin Bushings are pushed into the holes of the SAVAGE Hanger & sit tightly in position. They hold the Kingpin in a wear-free position between the moving metal parts of the SAVAGE hanger & Baseplate.

The Bushings allow the movement (steering) without wearing out the metal parts.

The Kingpin bushings are a small perishable item. They are subjected to a lot of forces & stress, although they are now supported by a 2mm Kingpin Bushing re-enforcement ring, through regular abuse they will ultimately wear out & eventually need replacing.

Depending on what surface you are riding on & the nature of your riding style will depend on how long these bushings will last you.

To make sure your trucks are always performing at their best you should keep some spare Bushings on the shelf at home & inspect these them on a regular basis (preferably before riding) & in particular replace any bushings that are showing signs of wear & then even if they are not broken from time to time replace them anyway...

One way to check your bushings is to man h&le the truck when fitted to the deck... If you feel any play between the Hanger & the Baseplate then you definitely need to replace the bushings straight away before you do damage to the hanger.

Worn out Bushings will cause the kingpin to rub in the Hanger kingpin hole... The kingpin is much stronger than the Aluminium used to make the hanger & the kingpin will wear a nasty hole of you do not fix the problem before it gets too late.

If you ride with trucks that have play in them, then you are lining yourself up for an accident... If you feel any play, this can at speed convert to wobble & we all know riding with a board with a wobble will lead to accidents, so it is wise to check your bushings & rings on a regular basis.

The difference between the four bushings is the thickness of the base. The different base sizes are 1mm, 1.5mm, 2mm and 2.5mm. 2.5mm is the standard size we work to. As all trucks have 4 bushings this .5mm difference in each of the bushing bases allows us to bridge a maximum distance of 2mm (4x.05mm=2m) resolving any foreseeable problems.

Kingpin Bushings 3mm Base - for Spring Trucks

The Kingpin Bushings sit tightly in position & hold the Kingpin in a wear-free position between the moving metal parts of the hanger & Baseplate. The Bushings allow the movement (steering) without wearing out the metal parts. The Kingpin bushings are a small item & are subjected to a lot of forces & stress, through regular use they will ultimately wear out & need replacing. Depending on what surface you are riding on & the nature of your riding style will depend on how long these bushings will last you.

To make sure your trucks are always performing at their best you should keep some spare on the shelf at home & inspect these tiny bushings regular basis (preferably before riding) & in particular replace any that are showing signs of wear & then even if they are not broken from time to time replace them anyway...

The difference between the four bushings is the thickness of the base. The different base sizes are 1mm, 1.5mm, 2mm and 2.5mm. 2.5mm is the standard size we work to. As all trucks have 4 bushings this .5mm difference in each of the bushing bases allows us to bridge a maximum distance of 2mm (4x.05mm=2m) resolving any foreseeable problems.

Kingpin Bushing Re-enforcement Ring - Custom

2.5mm Kingpin Bushing Re-enforcement Rings are used in the assembly of all of the TRAMPA Spring Trucks with EXCETION TO the SAVAGE Trucks which use 2mm Kingpin Bishings & 2mm re-enforcement rings in its assembly.

The Kingpin Bushing Re-enforcement Ring is pushed onto or over the top of the Kingpin bushing after it has been inserted into the Hanger & before the baseplate is presented for connection.

The Re-enforcement ring spreads the weight of the connection to give extra support to the tiny kingpin bushings, whilst still allowing the free movement between the Hanger & Baseplate (steering), without wearing out the metal parts.

The Kingpin bushings are a small perishable item. They are subjected to a lot of forces & stress, although they are now supported by the Kingpin Bushing re-enforcement rings, through regular abuse the bushings will ultimately wear out & eventually need replacing.

Depending on what surface you are riding on & the nature of your riding style will depend on how long your Kingpin bushings will last you, regular service will prolongue their life but they should be replaced when possible.

To make sure your trucks are always performing at their best you should keep some spare Bushings on the shelf at home & inspect these them on a regular basis (preferably before riding) & in particular replace any bushings that are showing signs of wear & then even if they are not broken from time to time replace them anyway...

One way to check your bushings is to man h&le the truck when fitted to the deck... If you feel any play between the Hanger & the Baseplate then you definitely need to replace the bushings straight away before you do damage to the hanger.

Worn out Bushings will cause the kingpin to rub in the Hanger kingpin hole... The kingpin is much stronger than the Aluminum used to make the hanger & the kingpin will wear a nasty hole of you do not fix the problem before it gets too late.

If you ride with trucks that have play in them, then you are lining yourself up for an accident... If you feel any play, this can at speed convert to wobble & we all know riding with a board with a wobble will lead to accidents, so it is wise to check your bushings & rings on a regular basis.

As all the metal parts are hand constructed here in the UK, so it has been easy for us to control the construction of the Trucks to ensure each truck that leaves the building has the correct size bushings fitted & therefore we can ensure totally smooth steering system in every Truck like we always brag about :-)

Custom Colour Spring - Powdercoated Sprung Steel Steering Springs

TRAMPA's SPRINGS are coiled to precision & fit into the TRAMPA Spring Trucks perfectly. They easily squeeze into the space between the Baseplate & Hanger & being made to measure they are firstly very easy to fit with no clamps or tools required to squueze them into position & secondly to be super responsive to the rider.!  Once the spring assembly is fitted correctly the steering resistance is taken up instantly!

Our Springs have been designed to work in perfect harmony with the TRAMPA DAMPA's & TRAMPA SPRING RETAINER providing maximum performance from the "Spring assembly" to the rider. The DAMPA's drop into the SPRING & the SPRING RETAINERS seal the ends of the spring, holding the DAMPA in exact position to be pre-loaded & squeezed into the truck. Using just a little bit of muscle, squeeze the loaded spring into the truck, then lock the spring into position using the Spring Adjuster & M5 x 12mm Countersunk Bolt. The TRAMPA spring Truck steering system is highly responsive & totally customisable by interchanging the DAMPA's to harder Urethane. Other Mountain Board brands springs will not fit the TRAMPA Trucks as they are a different in dimension.

TRAMPA Springs are available in a selection of Powder-coated colours for good looks & of course for best surface coating protection & this one comes to you in Powder Coated Black. 

Spring Retainer - Specially designed to work in harmony with the Dampa & spring

TRAMPA's very own & very special re-enforced Spring retainer. Specifically shaped to fit tightly inside the TRAMPA springs & snugly hold the Trampa Dampa in the exact position to give precision steering to the rider. Made by Injection Moulding using original Dupont Materials, with an extra wide Marine-Grade Stainless Steel Flanged Insert seated internally, re-enforcing the Retainer. The Extra Strength of the re-enforced flange, eliminates the need for a very fiddly fitting washer, that is still found in the MBS and Scrub boards today.

Designed to work in harmony with the TRAMPA spring and TRAMPA Dampa to help create immediate resistance from your steering system. With TRAMPA Embossed around the rim of the retainer - you'll have performance with pimpness!

Custom TRAMPA DAMPA

TRAMPA's SPRINGS are coiled to precision & fit into the TRAMPA Spring Trucks perfectly. They easily squeeze into the space between the Baseplate & Hanger & being made to measure they are firstly very easy to fit with no clamps or tools required to squeeze them into position & secondly to be super responsive to the rider.!  Once the spring assembly is fitted correctly the steering resistance is taken up instantly!

Our Springs have been designed to work in perfect harmony with the TRAMPA DAMPA's & TRAMPA SPRING RETAINER providing maximum performance from the "Spring assembly" to the rider. The DAMPA's drop into the SPRING & the SPRING RETAINERS seal the ends of the spring, holding the DAMPA in exact position to be pre-loaded & squeezed into the truck. Using just a little bit of muscle, squeeze the loaded spring into the truck, then lock the spring into position using the Spring Adjuster & M5 x 12mm Countersunk Bolt. The TRAMPA spring Truck steering system is highly responsive & totally customisable by interchanging the DAMPA's to harder Urethane. Other Mountain Board brands springs will not fit the TRAMPA Trucks as they are a different in dimension.

TRAMPA Springs are available in a selection of Powder-coated colours for good looks & of course for best surface coating protection & this one comes to you in Powder Coated Black. 

Spring length - 66.5mm
Spring external diameter - 30mm
Spring internal diameter - 21mm
Spring thickness - 4.2mm
Black Powder coated steel Spring.
Weight: 64g

The TRAMPA DAMPA is a Urethane Elastomer that fits inside the Spring of a Truck. Its purpose is to support the Spring & give extra resistance during steering. Its clever design has three balls stacked & connected on-top of each other. The middle ball is slightly fatter than the outer two, during steering they all compress against each other giving greater feed back in your turns. This stacked design gives a fantastic progressive feel to steering.

By varying the SHORE DUROMETER (Rubber Hardness) strength of the Urethane mixture, we can control the amount of movement in the DAMPA. This in turn allows the rider to custom tune the resistance of their steering perfect to their requirements. The spheres of the DAMPA fit perfectly into the cup of the specially made TRAMPA SPRING RETAINER which is the part that locates & locks the Spring in the the TRAMPA SPRING TRUCKS, and they instantly start to work with the slightest movement from the rider. TRAMPA DAMPA's work in harmony with the rider, supplying the perfect amount of steering resistance whilst eliminating all chances of speed wobble. Now available in 5 different steering resistance's for all levels of rider out there, Orange DAMPA's are for easy steering, whilst White DAMPA's are for the totally committed! 

Turning the Spring Adjuster clockwise pre-loads the tension in the Spring and DAMPA. This can be adjusted on the fly to suit the terrain & conditions. Turning the spring adjuster too much will put pressure on the DAMPA & eventually it may split. Rather than putting too much pressure into the DAMPA, consider up-grading the DAMPA to a harder Shore Durometer as this will most likely increase your performance than over tightening a DAMPA that's not stiff enough for you. Please use the table below for guide.

Spring Adjuster - Marine Grade Stainless Steel

TRAMPA's very own & very special SPRING ADJUSTER is made using A4 MARINE GRADE STAINLESS STEEL & is guaranteed never to rust on you! The Spring adjuster is fitted to the trucks once the springs have been pushed into position. The spring adjuster pre-tensions the steering suitable for the rider’s requirements. We designed the Spring Adjuster to be slightly shorter in length than other brands’, to avoid  the tip of the adjuster poking through the internal of the Spring Retainer, and interfering with the performance of the DAMPA located on the inside of the Retainer.

Should you need extra resistance from your steering because you wish to ride fast, or if you need more steering because the course is twisty, then you can very easily & quickly adjust the resistance of your steering by simply turning the spring adjuster in the correct direction. To get the most out of your trucks on changeable terrain, simply use a 4mm Allen Key to make your adjustments. Winding the Spring Adjuster clockwise increases the steering resistance, which in turn restricts wobble at high speed. Turning the Adjuster anti-clockwise loosens the steering allowing a more carvey ride.  

DO NOT over tighten your Spring Adjuster, as this may crush your DAMPA. If you need more steering resistance upgrade your DAMPA's & do not over tighten!

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

HYPA Hub 3.75x 2 Inch - Any Colour you like!

TRAMPA's 6 spoke HYPA Hub is by far the lightest & weight for weight compared, the strongest 3.75-inch hub on the market today!

The HYPA hubs 6 spoke design is technically advanced & is manufactured using original Du-Pont materials & the very latest in precision injection molding machinery - No quality expense is spared! This deluxe combination of technical design, top quality machinery & original genuine materials, creates a product that is far superior to all of our competitions, resulting in performance that is well beyond normal expectations. This extra performance means the TRAMPA HYPA hub can handle much higher than recommended tyre inflation pressures, generating substantially higher than normal roll speeds. Back in the day during testing, our crash test dummies (i mean the Team riders) commonly rode with these hubs well above 80psi & beyond.... 

The HYPA hubs are held together using only the best Marine Grade (A4) Stainless steel Nuts & Bolts so they definitely wont rust on you (EVER) & are therefore perfect for bad conditions. All the Bolts used by TRAMPA have been dipped in a special Blue Locking Paste & all the Nuts are fitted with the world renowned Nylon "Nylock" Nut locking System, all these no expense spared small details ensure you get the absolute best hub possible!

HYPA hubs are available in loads of different colours & surface finishes, all of which are TRAMPA embossed between the spokes proving the top quality! Do not buy imitations as they will not perform the same!  TRAMPA’s own high class Steel Bearings, (Genuine  ABEC 5 rated Bearings) push perfectly into the HYPA hub bearing housing, guaranteeing the fastest spin rate to the wheel possible. Use either Bearing reducer sleeves into 12mm Bearings or use TRAMPA's 10mm Bearings to fit the HYPA hubs onto smaller sized skate axles. HYPA hubs are compatible with all known 8-inch tyres currently on the market including MBS & Scrub. Put quite simply – HYPA hubs are by the Best!

Along with many other applications that these wheels will fit too, the HYPA hub will fit and accept ALL the other brands of mountain boards on the market including MBS, SCRUB & KHEO, so when you are looking for an upgrade to your ride you know where too look! Basically the HYPA Hub will fit to anything that uses a Imperial 7/16ths (9.52mm) or 12mm bearings to fit onto the axle. If you already have your own 12mm bearings there are conversion spacers available to convert your 12mm bearings to work on the 7/16ths Imperial (9.52mm) skate axles and a different size spacer to convert them to fit 10mm (metric) scooter axles (see associated parts for details).

Bearings are supplied at a discounted price when purchased with hubs...

Rim Diameter 3.75 Inch
Rim Width      2 Inch or 50mm
​Fits all Tyres with 3.75 Inch rim inflating up to 8 inch in Diameter

8 Inch Inner Tube PRIMO 8x2 inch 200x50mm - fits 3.75 inch Rims & 8 inch tyres

PRIMO's own 8 Inch Inner Tube has dimensions of 200mm (outer diameter) x 50mm (width) & will fit into all known 8 inch Tyres & ATB hubs on the market!

The CST PRIMO Inner Tube incorporates slightly thicker rubber into its manufacture process which means the tube is slightly heavier than alternatives but does allow the rider to inflate slightly higher. This extra thickness also gives some extra resistance to punctures, but punctures suck, so always carry a spare inner tube when you are riding as you never know when you might get one.  

The PRIMO Tube uses a 90º Brass Inflation valve which will not rust on you & comes as you would expected with a plastic "anti dust" valve cap!

TRAMPA MUD-PLUGGER 8 Inch Tyre measure 3.75x 2x 8 Inch or 200x50mm with 3.75 inch Rim fits all 3.75 inch Hubs - BLACK

TRAMPA's 8 Inch MUD-PLUGGER Tyre is a super advanced & incredibly lightweight tyre that fits all the 3.75 inch hubs on the market. It is the perfect tyre choice when your when riding in the worst of conditions, seeking the maximum grip possible!! 

Measuring 8x 2 Inch or 200mm x 50mm with a 3.75 Inch Rim,  the MUD-PLUGGER tyre has a box shaped construction, whilst the 2PR 'soft compound' rubber coating has an aggressive & well spread tread pattern that see's 'Grip on top of Grip'. Making the Mud-Plugger tyre 'Box shaped', having much straighter sides for example compared to the kind of Ballon shape of the 8 inch ALPHA tyre, allows for much more 'Surface Contact' resulting in much more 'Traction' for the user.

Mud-Plugger tyres also have a 'Wide Center Bead' allowing good top end roll speeds but as it is so Deep Grooved (5mm at the deepest) & very 'knobbily' around its sides to cut through the deepest of mud, suggests the appearance of the TRAMPA Mud-Plugger tyre works best in really bad conditions more than straight line speed on Hard packed surfaces!

TRAMPA's 8 Inch Mud-Plugger tyre has 3.75 inch Steel Bands molded into rims of the tyre, therefore the 8 Inch Mud-Plugger tire will fit onto all 3.75 inch hubs & 3.75/4 inch hubs currently on the market.

To enhance grip capabilities to the max the Mud-Plugger Tyre is manufactured using a Soft Compound '2PR rubber' wrapped around whats known as a High TPI (Threads per Inch) construction. A High TPI results in a super lightweight, very supple yet strengthened construction that further enhances grip & is more resistant to punctures. High TPI is applied to all top quality bicycle tyres. 

Having invested into professional testing at the factory & using our own TRAMPA hubs to make the testing, the factory have given this tyre a recommended maximum inflation pressure of 65psi (BUT ONLY WHEN FITTED TO TRAMPA HUBS) which is much more than any other brand & testament to the design & superior strength of the TRAMPA HUBs! Its true, the more you inflate your tyres the faster you will roll but these are off road tyres & so its not always good to have high inflation! Over inflation of your tyres may cause an explosion which could cause serious injury to yourself, however running your tyres as low as 20-25psi (depending on how much you weigh and how you ride etc) is more likely to give you the best grip when riding in the soft stuff....

130mm - Hand made TRAMPA Vinyl Sticker

Everybody loves stickers, especially TRAMPA VINYL stickers! TRAMPA vinyl's are pain-stakingly hand made at TRAMPA HQ using the absolute finest Vinyl material available! So long as the area it is to be stuck to is clean the Vinyl we use is guaranteed to stick well & not fade for well over 5 years. These BLUE vinyl stickers are sized to fit onto the top of the Trampa deck, the dimensions are 130mm long x 28mm high.

There are loads of colours to choose from and the price starts at just 30 pence each - so custom pimping your deck, car, van, boat, bedroom window or any other surface you can think of that would benefit with a TRAMPA logo slapped on it is really easy & cheap to do... Help TRAMPA the world with the Pimp-est vinyl stickers EVER!

To Apply - Ensure the surface is clean & grease free before applying the sticker. Peel the thick side away from the Masking tape so the sticker appears in reverse (negative) and simply lay the masking tape onto the surface in question. Using your fingers or a soft cloth, rub the masking tape, forcing any air out of the vinyl & allowing the vinyl to stick well. Then gently peel away the masking tape to reveal the Vinly. This VIDEO may help...

Everybody loves stickers, especially TRAMPA stickers! TRAMPA's Old Skool VINYL Stickers are pain-stakingly Hand Made at the TRAMPA HQ using the absolute finest Vinyl material available! So long as the area it is to be stuck to is clean the Vinyl we use is guaranteed to stick well & not fade for well over 5 years and most likely much longer! These BLUE Vinyl Stickers are sized to fit underneath the TRAMPA deck, the dimensions are 370mm long x 70mm high.

There are loads of colours to choose from & the price starts at just £2.50 each - so custom pimping your deck, car, van, boat, bedroom window or any other surface you can think of that would benefit with a TRAMPA logo slapped on it is really easy & cheap and easy to do...

Help TRAMPA the world with the Pimp-est vinyl stickers EVER! To Apply the Stickers - Ensure the surface you re applying too is clean & grease free before applying the sticker. Peel the thick side away from the Masking tape so the sticker appears in reverse (negative) and simply lay the masking tape onto the surface in question. Using your fingers or a soft cloth, rub the masking tape, forcing any air out of the vinyl & allowing the vinyl to stick well. Then gently peel away the masking tape to reveal the Vinly.

580mm - Hand made TRAMPA Vinyl Sticker