This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

Spring Retainer - Specially designed to work in harmony with the Dampa & spring

Spring Retainer - Specially designed to work in harmony with the Dampa & spring
RRP
£3+

TRAMPA's SPRINGS are coiled to precision & fit into the TRAMPA Spring Trucks perfectly. They easily squeeze into the space between the Baseplate & Hanger & being made to measure they are firstly very easy to fit with no clamps or tools required to squeeze them into position & secondly to be super responsive to the rider.!  Once the spring assembly is fitted correctly the steering resistance is taken up instantly!

Our Springs have been designed to work in perfect harmony with the TRAMPA DAMPA's & TRAMPA SPRING RETAINER providing maximum performance from the "Spring assembly" to the rider. The DAMPA's drop into the SPRING & the SPRING RETAINERS seal the ends of the spring, holding the DAMPA in exact position to be pre-loaded & squeezed into the truck. Using just a little bit of muscle, squeeze the loaded spring into the truck, then lock the spring into position using the Spring Adjuster & M5 x 12mm Countersunk Bolt. The TRAMPA spring Truck steering system is highly responsive & totally customisable by interchanging the DAMPA's to harder Urethane. Other Mountain Board brands springs will not fit the TRAMPA Trucks as they are a different in dimension.

TRAMPA Springs are available in a selection of Powder-coated colours for good looks & of course for best surface coating protection & this one comes to you in Powder Coated Black. 

Spring length - 66.5mm
Spring external diameter - 30mm
Spring internal diameter - 21mm
Spring thickness - 4.2mm
Black Powder coated steel Spring.
Weight: 64g

The TRAMPA DAMPA is a Urethane Elastomer that fits inside the Spring of a Truck. Its purpose is to support the Spring & give extra resistance during steering. Its clever design has three balls stacked & connected on-top of each other. The middle ball is slightly fatter than the outer two, during steering they all compress against each other giving greater feed back in your turns. This stacked design gives a fantastic progressive feel to steering.

By varying the SHORE DUROMETER (Rubber Hardness) strength of the Urethane mixture, we can control the amount of movement in the DAMPA. This in turn allows the rider to custom tune the resistance of their steering perfect to their requirements. The spheres of the DAMPA fit perfectly into the cup of the specially made TRAMPA SPRING RETAINER which is the part that locates & locks the Spring in the the TRAMPA SPRING TRUCKSand they instantly start to work with the slightest movement from the rider. TRAMPA DAMPA's work in harmony with the rider, supplying the perfect amount of steering resistance whilst eliminating all chances of speed wobble. Now available in 5 different steering resistance's for all levels of rider out there, Orange DAMPA's are for easy steering, whilst White DAMPA's are for the totally committed! 

Turning the Spring Adjuster clockwise pre-loads the tension in the Spring and DAMPA. This can be adjusted on the fly to suit the terrain & conditions. Turning the spring adjuster too much will put pressure on the DAMPA & eventually it may split. Rather than putting too much pressure into the DAMPA, consider up-grading the DAMPA to a harder Shore Durometer as this will most likely increase your performance than over tightening a DAMPA that's not stiff enough for you. Please use the table below for guide.

 

COLOUR

Stiffness

Shore

Suitability Guide

ORANGE

Super Soft

55

Light Riders / Crazy Carvers!

PINK

Soft

60

Beginner Carvers

YELLOW

Average

65

Beginner / Intermediate

GREEN

Average (75kg+)

75

Intermediate / Adult sized rider

RED

Firm

80

Advancing rider / Teenage Freestyler

BLUE

Stiff

85

Fast & Advanced Freestyle Rider

WHITE

Stiffest

90

For the Insane only!

TRAMPA's very own & very special re-enforced Spring retainer. Specifically shaped to fit tightly inside the TRAMPA springs & snugly hold the Trampa Dampa in the exact position to give precision steering to the rider. Made by Injection Moulding using original Dupont Materials, with an extra wide Marine-Grade Stainless Steel Flanged Insert seated internally, re-enforcing the Retainer. The Extra Strength of the re-enforced flange, eliminates the need for a very fiddly fitting washer, that is still found in the MBS and Scrub boards today.

Designed to work in harmony with the TRAMPA spring and TRAMPA Dampa to help create immediate resistance from your steering system. With TRAMPA Embossed around the rim of the retainer - you'll have performance with pimpness!

Spring Retainer with Marine Grade Stainless Steel Insert
Weight: 9g
Quantity required:
The total number of this part in stock is 6239
RRP £3 - each

Excluding VAT
HCC: 7320208190

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon