Home»Trucks»12FiFties - 12 Inch Wide Longboard Trucks»12Fifties Extra Wide All Terrain Longboard Truck

TRAMPA's Super Sexy 12FIFTIES Extra Wide Longboard Trucks are absolutely fabulous! CNC precision shaped from a solid Block of T6 Aluminum, the 50º Mounted Hanger measures 12.5 Inch wide & is fitted with 9.525mm (3/8ths of an inch) Hardened Steel axels which means the EXTRA WIDE Longboard Truck will accommodate every wheel in the TRAMPA product range from 83 or 90mm STICKIES Longboard WHEELS, 125mm GUMMIES Longboard Tyres & The Amazing 6.5 Inch URBAN TREADS Tyres! 

Being 12 Inch wide & Mounted at 50º the 12Fifities Extra Wide Longboard trucks are named after around dimensions. The Extra Wide Longboard Trucks provide high speed stability & the opertunity to add Pneumatic tyres, which beings a complete new ride experience when riding the rough roads that around us, cruising over cracks in the pavement is glorious!

3/8ths Nut - Marine Grade Stainless steel Nylock HALF nut W3/8 - 24T UNF

This very special Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore reducing weight in the Truck also! A few Grams here & a few grams there soon adds up to quite alot & that makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area...

This very special 3/8^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W3/8_^ths - 24T - UNF. This Nut is used to hold the wheels onto the axles of the 9.525mm (3/8ths of Inch or otherwise referred to as 10mm) SKATE TRUCKS & also the Spring Trucks fitted with TITANIUM axles. This Nut is also used to hold the KINGPIN in position on all Skate Trucks. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 14mm or 9/16^ths of an Inch spanner to tighten the Nut onto the Axle or Kingpin, do not overtighten the nut, allow the wheel to spin freely but not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

 - Fits to 9.525mm (3/8ths) Axles & Skate Truck Kingpins

3/8ths Nut - Marine Grade Stainless steel Nylock HALF nut W3/8 - 24T UNF

This very special Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore reducing weight in the Truck also! A few Grams here & a few grams there soon adds up to quite alot & that makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area...

This very special 3/8^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W3/8_^ths - 24T - UNF. This Nut is used to hold the wheels onto the axles of the 9.525mm (3/8ths of Inch or otherwise referred to as 10mm) SKATE TRUCKS & also the Spring Trucks fitted with TITANIUM axles. This Nut is also used to hold the KINGPIN in position on all Skate Trucks. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 14mm or 9/16^ths of an Inch spanner to tighten the Nut onto the Axle or Kingpin, do not overtighten the nut, allow the wheel to spin freely but not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

 - Fits to 9.525mm (3/8ths) Axles & Skate Truck Kingpins

PRECISION Shim spacer - STAINLESS STEEL - Bridges tiny gaps on axles - 9.525 x 13.525 x 1mm

This tiny STEEL Shim Spacer is precision made to give maximum performance! It is used to hold the bearings in the perfect position & also to bridge tiny gaps on the axles, ensuring an accurate fit with NO rattles!

The Shim spacer slips onto the axle fitting either side of the Bearings when the wheel is being fitted onto 9.525mm Axles.

This tiny spacer positions the wheel perfectly on the axle, holding the Bearing in the best possible place to help achieve maximum spin rate for the wheel. Its little parts like these that suffer the most amount of abuse, especially when they are used in the harsh conditions that they are. Check from time to time they are in good order & possibly replacing them every now & then this good proactice will ensure your board stays in tip-top condition, always!

12FiFties Longboard Hanger 310mm with 9.525mm SOLID Steel Axle

TRAMPA’s amazing 12FiFties Extra Wide Longboard Trucks are amazingly responsive, strong & adaptable.

Designed to be used in conjunction with TRAMPA's ORRSOM longboard deck, they provide a market leading variety of customisation options only dreamt about with your standard longboard.

If you love building your own longboards, be it electric powered or gravity fed, this could be the new truck for you!

12FiFties Hangers measure 12.5 inches wide,  the extra width providing superior stability at high speed, as well as the clearance for adding larger wheels. Compatible wheel sizes range from 83mm Trampa stickies - for ultimate tarmac cruising, all the way through the range up to 8'' pneumatic tyres - providing the most unrivalled off road experience.

Trampa have achieved this by factory fitting 9.525mm hardened steel axles, then offering different bearing alternatives to suit; Stickies R6-2RS, Skate 28x9.525mm or  R6001RS 28x12mm with a reducer sleeve.

This is the most versitile longboard truck for any terrain type! 

Designed with our standardised skate kingpin (9.4 x 50mm) & mounted at 50º angle to the baseplate for optimum steering responsiveness. 

Baseplates are available in 10 different anodonised colours for unrivalled customisation! 

Precision CNC’d from solid blocks of T6 heat-treated Aluminium, 12FiFties HANGERS are remarkably strong, able to withstand the forces, bumps or crashes they’ll inevitably recieve if ridden properly. Aswell as looking the part with a polished silver finish!

The hanger body has been CNC'nd along the complete length to 19.5mm x 19.5mm, and then grooved to allow the electric motor mount to be preicisely clamped to the truck. The mount itself consists of a simple laser-cut carbon panel and a CNC'd 12FiFties clamping ring available in the motor mounts section of the website.