This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

TRAMPA's DRIFT-E-TRIKE is assembled from many of the existing parts TRAMPA already uses to make its amazing Electric Mountainboard decks giving so much unreal fun!!

alt : VESC 6 MkVI

MASSIVE Monster Box BASE for 2WD

The Massive Monsterbox Base connects to all vertical panels in a Massive Monster Box or Double Stack Massive Monster Box. They are used with grommets to allow entry into the box by the phase and sensor cables, and the edges of the box are where the hex spacers mount. Additionally, the base is where any Monsterbox is mounted to the board. In this case that can be done via the standard bushing system or Dogbone mounting system. This panel is only designed to operate with 2 motors. 

MASSIVE Monster Box LID

The Massive Monsterbox MkV Lid rests on top of the side and end panels of the Massive Monsterbox MkV and centers the screws into the hex spacers to hold the box together.

MASSIVE Monster Box SIDE PANEL - BLANK LI-PO

The side panel is a structural component of the Massive Monster Box that connects the lids and base of the box together. 

MASSIVE Monster Box 2mm DOUBLE STACK SIDE PANEL - CHARGER LI-PO

The side panel is a structural component of a Double Stack Massive Monster Box that connects the lids and base of the box together. Has cutout for charging port.

MASSIVE Monster Box 2mm DOUBLE STACK SIDE PANEL - BLANK LI-PO

The side panel is a structural component of a Double Stack Massive Monster Box that connects the lids and base of the box together.

MASSIVE Monster Box 2x VESC 6 2mm DOUBLE STACK Mounting Panel (2WD) LI-PO

Used for mounting two VESC 6’s on the inside of a Double Stack Massive Monster Box.

RED 1036 Strand 4mm core Silicon Coated Cable with BLACK TRAMPA Logo - Priced per 10cm

Allow your Electric board to gain the maximum performance by fitting the very highest quality Electrical Cables & Connectors and let the power in your battery flood out as performance at the rear wheels!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn in production to produce to such a small amount of such a high quality cable, but finally TRAMPA has had what it wanted delivered & we can now supply you with Super high Quality Silicon Cables in RED or BLACK with co-orinating BLACK & WHITE TRAMPA logos to prove the quality & show off the kind of performance your board is capable of! :-)

TRAMPA's gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. The Blaff cables have enclosed in the Besilen insulated​ Silicon Outer sleeve, 1800 Highly flexible TOP QUALITY Copper strands in the center... BLAFF cable is used for the highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation (Trains, Trams, Planes) as they have a global reputation of incredible high standards.

TRAMPA Silicon cables solder perfectly into XT60 & XT90 connectors to give the perfect connection to your power source. A soldering service for a pair of cables is available though TRAMPA when you purchase the cables as pairs,

RED Silicon Casing with contrasting BLACK TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

BLACK 1036 Strand 4mm core Silicon Coated Cable with WHITE TRAMPA Logo - priced per 10cm

Allow your Electric board to gain the maximum performance by only fitting the very highest quality Electrical Cables & Connectors to let the power in your battery flood out as performance at the wheel!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn to produce to such a small amount of cable at such a high quality standard, but finally TRAMPA has got what it wanted & has now taken delivery of its own Super high Quality Silicon Cables in RED & BLACK with contrasting Black & White TRAMPA logos to prove the quality & show off the kind of performance your board is harvesting! :-)

TRAMPA's Gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. BLAFF cable is used for highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation and the likes (Trains, Trams, Planes) as they have a global reputation of incredible high standards. 

Enclosed in the Besilen insulated​ Silicon Outer lies 1800 Highly flexible TOP QUALITY Copper strands in the center...

BLACK Silicon Casing with contrasting WHITE TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

Cable Harness for wiring Power Switches to VESCs

Harness allows connection between VESC 6 MkIII or newer and on/off switch.

XT90H-F with Housing - Female

On most TRAMPA electrical components, you’ll find AMASS XT90 connectors.  With a strong nylon plastic body & cylindrical brass contacts that comfortably fit 10-12 gauge wires, XT90 connectors are rated to handle 90 Amps continuous – but have been tested up to 270A!

Available as standard, or Anti-Spark - we recommend Anti-Spark for connections that are likely to be plugged/unplugged often.

TRAMPA Switch with 5V LED QUALA-T logo & 16mm Stainless Steel Fixing Nut

The TRAMPA 'QUALA-T" stamped Power Switch is a sexy little switch & to co-ordinate with the huge array of anodised & painted colours that TRAMPA offers to tie into all the other kit we offer is available in 6 different colours - RED, BLUE, YELLOW, GREEN, WHITE, PINKY/PURPLE

Which means no more loop keys!
All TRAMPA Mountainoboards Boards fitted with VESC 6 MKIII & any later models can now be fitted with power buttons for easy powering on/off and a much sleeker looking board!

You will need a Power Switch Cable harnesses to plug in

The QUALA-T Switch is Non-latching & limited to a Max voltage of 5v 

TRAMPA Switch 16mm Fixing nut - Stainless Steel

Used to secure the edge of an On/Off switch to carbon panels.

5mm Cable Entry OPEN Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes in Monster Box side panels for water proof assistance & Neat Cabling

5mm Cable Entry Open Rubber Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes in Monster Box side panels for water proof assistance & Neat Cabling

OVAL Rubber BLIND Grommet Cable Entry Hole - Fits in Monster Box side panels for water proof assistance & Neat Cabeling

This OVAL Rubber BLIND Grommet Cable Entry Blank is used to seal of Entry Holes in MONSTER Box, BEAST Box & Underboard Battery Tray which fits on the ORRSOM longboard. Simply push the Oval Grommet into position & your entery holes is sealed from moisture & dust.

If you need to push a cable through, use a sharp knife and carefully slice through the rubber membrane.

5mm ROUND BLIND Rubber Grommet for 5mm TRAMPA Silicone Cable

This 5mm Round Blind Grommet is used to seal off un used Motor Cable Entry Holes in the MONSTER Box, BEAST Box & Underboard BATTERY Box.

The 5mm Round Blind Grommet should also be fitted into all Battery Boxes which are using the Motor Cable entry holes as passing the cables through the 'OPEN' Grommet seals the hole best as possible & protects from the ingress of moisture & dust. 

To open the grommet to pass a cable through simply use a sharp Knife to press against the pre pressed slicing line & slice open the Rubber Membrane to allow you to push your cables through. Easy!

 

TRAMPA's own 6376 160Kv 3800w DC Brushless & SENSOR-LESS Motor

TRAMPA's very own purpose made 160 KV 6376 Out-Runner Motor provides 160RPM per volt. CUSTOM MADE to handle HIGH Power outputs.

This Motor has many NEW features that increase both hardiness & efficiency!

- Improved thermal design; with a more thermally-connected-mass, heat can dissipate much more efficiently. The new Rotor bodies feature raised rings that increase surface area, further helping heat dissipation.

- Stronger Hardware; larger & stronger bolts have been used throughout the motor, improving the motor’s strength & sturdiness, while making maintenance a lot less fiddle-y.


- Optimised Air-cooling; Stator cooling via air-flow - larger openings on the stator & having no sensor PCB both help to encourage a cooling flow of air through the motor. Further improve the air-flow using the MKII Motor Housing & Fan End-cap Kit.    

- Accurate & faster temperature readings; With a heat sensor glued to the copper windings in the ideal location, it's possible to get faster and more accurate motor-temp readings, which is important for future sensorless startup algorithms.

- Optimised for sensorless rotor position detection; With no sensor PCB inside, this motor works best when used with a VESC Speed Controller featuring Advanced Sensorless Startup - when paired & activated the motor will be able to reach full torque at 0RMP! 


All TRAMPA Motors use Premium high-temperature Copper & the highest grade of Neodymium Magnets available. The magnets connect to an Extended & Heat treated 8mm Steel Axle shaft that's locked in a balanced position with 4 precision Bearings. All screws & fixings used in the assembly are Marine grade Stainless Steel. All creating super-tough  motors that can easily out-perform the competition!

Our special design allows you to fit mesh filters, or entire Motor housings, preventing the impregnation of particles entering in the motor & stopping them running smoothly. The motor Stators are equipped with twelve M4 threaded mounting holes, sitting on a 44mm diameter circle. The extra holes allow the motor to be mounted at the exact angle needed so the motor cables always sit in the perfect angle, towards the mount or deck.

Using 38.5mm x 8mm Heat-Treated Hardened-Steel Motor Shaft (fitted with a 12x3x3mm KEYWAY locator as standard), the extra length of the Axle allows us to add adequate support with Motor Axle Supports, & allows us to fit  Extra wide Motor Pulleys for the 15 - 20mm wide HTD 5M STRONGBELTs we use as standard, guaranteeing a much stronger power delivery.

Two 3x3x12mm KEYWAYs lock the Axle shaft at both ends (1 to the Rotor & 1 to the Motor Pulley), eliminating any & all "Motor slip", & providing maximum performance to the rider, while gaining critical data for the VESC speed controller.

The Heavy Duty & high quality power cables use 4mm Gold Plated Bullet Connectors to connect to a power source. 

CUSTOM Motor protection Housing - TWIN MOTOR

HALF CAGE  

This filter has been designed for those who want to save as much weight as possible while still maintaining a level of protection against grit and dust. 
 
The filter mesh is 0.15 mm, this will only allow particulates that are small enough to pass through the air gap between motor magnets and the stator. 

Allowing for consistent cooling of the motor while reducing wear on the motor. 

•Available in 10 colours. 

•Aluminium and stainless construction. 

•Compatible with Trampa motor fan. 

Pairing with the MKII Delrin Motor Housings, these fans secure to the ends of 6376 Motors, creating a cooling airflow around the motors - reducing running motor temp, and increasing efficiency! 

Motor Fan - Connects to the end of the Motor & Spins to help maintain temps low

Pairing with the new MKII Delrin Motor Housings, these fans secure to the ends of 6376 Motors, creating a cooling airflow around the motors - reducing running motor temp, and increasing efficiency!

After many different designs and prototypes, this shape has proved the most efficient at creating an airflow that made a real difference to the motors’ performance.
Attaches to the end of motors using 5x M3x16mm Countersunk bolts.

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x12mm

TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.

TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....

VESC 6 MkVI PCB - The next generation - Benjamin Vedder Electronic Speed Controller

****Introducing the amazing VESC® 6 MKVI Speed Controller, the sixth major product update of the world famous VESC 6 motor controller. Packed with a variety of amazing new features, this VESC motor controller is certainly worthy of its pimpin’ gold logo.

The second VESC controller capable of hibernating, your board can conserve power while not in use - reducing power consumption to just 20μA – less than the self-discharge rate of the batteries. Or with automatic power off, your VESC controller can switch itself off after a set amount of time.

No more loop keys! Compatible with power buttons / switches, the VESC 6 MKVI controller can be ready to go with a single press / flick. If desired, multiple devices can share a single button.

Roll-to-start – it’s possible to set your board to power up with a small kick/nudge!

In its development, no Mosfet switches were used - due to their tendency to eventually blow up. This saves on the additional costs of replacing them, & also adds to the longevity of the VESC 6 MKVI.

When we developed the VESC 75/300 controller, it was obvious that most of its features would be handy to have in the VESC 6 controller format.  As a result, Benjamin Vedder took on the challenge and re-designed the entire PCB of the VESC 6 controller, to make new, powerful features available in a smaller & cheaper 60V rated package.

The VESC 6 MKVI controller features THREE PHASE SHUNTS & adjustable CURRENT / VOLTAGE FILTERS - detecting any motor attached more precisely and reliably than ever before. Consequently all kinds of motors now run as smooth as butter & react PERFECTLY LINEAR to throttle input commands.

You’ll also find a new IMU chip fitted - featuring a gyroscope, accelerometers and a compass, the VESC 6MKVI knows its 3D orientation in space, 3 axis acceleration values and directions. 

UAVCAN has been added to the firmware allowing to interact with commonly used flight controllers like the PIXHAWK ®* devices. An incredible 12,000 lines of code have been added for the new hardware releases. To make the VESC controller nearly indestructible, the low voltage rails were redesigned A-Z.

VESC-Tool software is now available as an Android™ compatible App, allowing you to configure your VESC or VESC controller array with only a few clicks. User specific PROFILES will let you change in between different setups with a single tap on the fly.

Using an original VESC 6 MKVI controllermotor detection is now more precise than ever. Extreme low inductance (0.5 μHmotors are no issue! 

Parameters for gearing and wheel diameter have been added, allowing display of speed, Wh usage per distance travelled, precise battery indicator, current consumption, duty cycle and power. Beautiful self-adjusting analogue displays make the readings of all parameters very enjoyable.

What makes the original VESC hardware so special?

The original hardware is perfectly matched to work seamless withe VESC-Tool software code. Both, hardware and software, have been designed by the same engineer, knowing all critical detail.

TRAMPA BOARDS LTD has teamed up with the internationally renowned 'YODA of electronics' (Benjamin Vedder) to bring to the world the most advance electronic speed controllers ever to be produced! Benjamin's family name is Vedder & the V in the brand VESC represents this. VEDDERs Electronic Speed Controller! There have been many ESC's before, but now the VESC line of products officially exists, made to work seamless with the latest software developments. Benjamin is globally renowned for his incredible electronics and software skills. He has worked tirelessly for well over 7 years fine tuning preceding versions of the globally famous & Trade Marked VESC products & after teaming up with TRAMPA BOARDS Ltd the development of the VESC product line has taken him to his highest capability yet.

The TRAMPA VESC controllers  comes fitted as standard with TRAMPA's very own & very special Silicone Coated & TRAMPA logo'd cables which are made up of 1036 Strands of Highly Flexible Top quality German copper. These quality details ensure the maximum performance at all times. Attached To the premium copper cables are genuine Amass XT90s connectors one side & 4mm Gold Plated Bullet connectors the other. The VESC 6 MKIII is installed with a custom moulded Internal Silicone Seal & is neatly fitted into the Heat sink which is a Solid Block of CNC'd  6061T6  Aluminum, used for dispensing the heat and offering maximum protection, allowing easy fitting and maximum good looks!..

The VESC line of produces are the most powerful & impressive Electric Speed Controller Benjamin has ever envisioned! They are  arguably by far the best and most versatile Electronic Speed Controllers the world has ever seen!! E Boarding, E-Biking, Remote control of all kinds including Drones & Robotics and Camera equipment (as well as thousands of industrial & recreational applications) are all about to be revolutionized by using the VESC series of products that will all come to the market soon...

Using the a VESC controller in your TRAMPA BOARD setup (Regardless of which model) will allow you to add any battery up to 12s with 60V of peak voltage. This is the perfect limit to give you incredible performance from your electric TRAMPA motors or similar. Using the new VESC TOOL software, you will be able to fine tune your performances relevant to your application, where you will be able to calculate your top end speeds & approx distance to travel using different combinations of power & gearing settings. Beautiful!

VESC controllers comes to you ready to plug in & go! They are delivered to you in a very stylish precision cut 6061 T6 aluminum heat-sink housing which has the TRAMPA & VESC logo beautifully laser etched to its surface & for further splash proofing we have invested into another mould for additional exterior Silicone Sealing which is available as an accessory to purchase.

The performance of the TRAMPA VESC controllers, compared to preceding third party models, is light years ahead! This is demonstrated in the cost as cheap non effective clones are sold according to their price not their quality. If you want the best performance then stick to the original hardware source - it will save you a lot of money on the long run and is a guarantee for ultimate performance and max compatibility with future software releases.

Our VESC controllers are being configured with the brand new Open Source, GPL V3 licensed VESC®-Tool Software:  www.vesc-project.com and on the Google Play Store™*.
The Open source, GPL V3 licensed VESC Firmware will come pre-installed on the device, allowing us to do extra testing of the device, prior to shipping.
This is the GPL V3 license contract for your reference:  www.vesc-project.com/GPL V3

Features

- Current and voltage measurement on all phases (three phase shunts)
- Adjustable current and voltage filters
- built in IMU chip (accelerometer, gyro)
- Regenerative braking
- Traction control (single and twin setup)
- Sensored or sensor less operation + hybrid mode
- Configurable RPM-, current-, voltage- and power limits
- Input source: PPM, Analog, NRF Nyko Kama Nunchuck
- Communication ports: USB, CAN,UAVCAN, UART
- Throttle curve and ramping for all input sources
- Separate throttle curves for acceleration and brakes
- Seamless 4-quadrant operation
- Motor revolution, amp hour, watt hour counting
- Display of speed, power, duty cycle, amp flow, estimated range and battery status on App
- Accumulated data from arrays of VESCs
- Real time data analysis and read out via communication ports
- Real time data analysis and read out via VESC-Tool APP or VESC-Tool software
- Adjustable protection against:

          -    Low input voltage
          -    High input voltage
          -    High motor current
          -    High input current
          -    High regenerative braking current (separate limits for the motor and the input)
          -    High RPM (separate limits for each direction).
          -    Over temperature (MOSFET and motor)

Technical Data Sheet

- Voltage: 11.1V – 60V (Safe for 3S to 12S LiPo).
- Voltage spikes may not exceed 60V! 52V max input voltage.
- Current: Continuous 80A, Burst 120A.  Values depend on the temperature and air circulation around the device!
- 5V 1A output for external electronics
- 3.3V 0,5A output for external electronics
- Modes: DC, BLDC, FOC (sinusoidal)
- Supported sensors: ABI, HALL, AS5047

* Android is a trademark of Google LLC.
Google and Play Store are trademarks of Google LLC.
PIXHAWK is a trademark of Lorenz Meier

VESC 6 CNC Aluminum Heat Sink Silicone Sealed Housing

CNC T6 Aluminum box Houses the VESC 6 perfectly

Measures 75 x 70 x 18mm

 

SPUR Gear Drive T6 Tub with TRAMPA Logo

CNC’d from a solid block of T6 heat-treated Aluminium, the SPUR GEAR DRIVE HOUSING is as strong as it is sleek. When paired with the CNC’d TUB COVER, the completed housing keeps the elements outs, the gears & belts clean & dry, & the whole board riding smoothly.
Designed to tightly slip around the CNC’d Hangers on Precision Vertigo Trucks, the Tub locks the entire drivetrain is accurately & securely in line.
With a bash-guard integrated into its design, you can be confident the tub will survive all the knocks-&-bumps its bound to receive on a ride.
Fits 10-tooth Straight or Helical Motor Pulleys & 58-tooth Helical or 59-tooth Straight-cut slave pulleys.
The Housing is perfectly symmetrical, allowing it to slide onto left or right drive trains.

 

TRAMPA SPUR Gear Drive T6 Aluminium Tub Cover

The Spur Gear Tub Cover is crucial to keeping your drive system free of dirt & debris. CNC’d from Premium Aluminium, giving it the perfect weight: strength ratio, the cover slots tightly over the Spur Gear tub, sealing off the drive system & leaving room for the Hub Adaptor & Rubber Seal

SPUR Gear Drive Bash Guard - RIGHT Side

Made using hardened steel, the spur gear bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the right drivetrain.

SPUR Gear Drive Bash Guard - LEFT Side

Made using hardened steel, the spur gear bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the left drivetrain.

SPUR Gear Drive Motor Adaptor

Housing a precision bearing for Motor Axle Support the SPUR GEAR DRIVE Motor Adaptor is used for attaching the motor securely to the drivetrain.
Precision CNC’d from hardened steel, the Motor Adaptor also allows for the use of PRO MOTOR HOUSING.

SPUR Gear Drive Hub Adaptor

The Hub Adaptor attaches the Slave Pulley to the Hubs, delivering the power of the motors to the wheels. Connects to SUPERSTAR or MEGASTAR hubs.

Precision CNC’d from Hardened Steel.

Connects to Slave Pulley using 5x m5x12mm Torx head screws.

Spur Gear Drive HELICAL or STRAIGHT Cut Slave Pulleys Made from POM or Steel

Spur Gear Drives are compatible with Straight-cut or Helical Gears.
Made from premium POM plastic
, the 58-tooth Helical Slave Pulley pairs with the 10-tooth Helical Motor Pulley, giving a gear ratio of 1:5.8. Compared to the 59-tooth Straight-cut Slave Pulley’s ratio of 1:5.9, Helical gears will ultimately have a higher top speed.  

Helical Gears provide more surface contact between the teeth, resulting in a smoother & quieter ride.

Straight-cut Gears are the cheaper option – still providing amazing torque & performance, while running a bit louder than helical.   

Connects to Hub Adaptor using 5x m5 x 12mm Torx head screws.

Spur Gear Drive CUSTOM Motor Pulley - c45 HARDENED STEEL

SPUR GEAR DRIVE Motor Mounts can run using Helical or Straight-cut pulleys.

Helical Motor Pulleys give a gear ratio of 1:5.8 when paired with the 58 tooth Helical Slave Pulley. The Helical shape allows for more surface contact between the Slave & Motor Pulley Teeth, creating a quiet & efficient drive. 

Straight-cut Motor pulleys pair with a 59 tooth Slave Pulley, giving a ratio of 1:5.9 – meaning there will be a tad more power when accelerating in comparison to the Helicals. However, due to less surface-contact between the gears, Straight-cuts are much louder when riding along (although we’ve found some mad people who like/prefer the noise!).

Made using Hardened Steel.

Mountainboard Motor Mount V-Ring TUB Seals - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

Mountainboard Motor Mount Truck Connector

Works with PRO BELT & SPUR GEAR Drives.
The Clamp housing slips over the axels of Precision CNC’d Vertigo Trucks, ensuring the drivetrain sits at the correct angle.
Working in conjunction with the Conical Clamp, when connected together the housing squeezes the clamp to the hanger, securely attaching the drivetrain to the trucks.

Precision CNC’d from T6 Heat-treated Aluminium.

Mountainboard Motor Mount Connector Conical Clamp

Works with PRO BELT & SPUR GEAR Drives.

Designed to work in conjunction & attach securely to Precision CNC’d VERTIGO trucks, the Conical Clamp slips tightly over the CNC’d square on the hanger of the trucks. When attached to the Clamp Housing, the Conical Clamp tightens around the hanger, ensuring secure & accurate Motor Mount attachment.

Precision CNC’d from T6 Heat-treated Aluminium.

Mountainboard Motor Mount Rubber pad for Conical Clamps - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

M4 x 10mm Dome Headed Head Allen-Key Bolt DIN6912 Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

This Bolt is DOME HEADED, meaning that when screwed into position it sits low & neatly over the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

- 6-8s Battery Box

- 8-10s Battery Box

-Underboard Battery Trays

M6 x 30mm Socket Capped Allen-Key Bolt for primo hub - Marine Grade Stainless steel

TRAMPA's M6 x 30mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the PRIMO 3 Spoke Hubs. The socket capped head of the Bolt screws neatly though the HUB eventually screwing into the Marine Grade Stainless Steel M6 Nylock Nut on the other side of the hub. 

Weighing just 8 grams each, these Bolts are lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers nuts & bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You’ll will need a 5mm Allen Key  to tighten & loosen the Bolt from the nut. Ensure all your Nuts & Bolts are tight before riding!

M5 x 20mm Regular Hex Head Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 16mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M3 x 18mm TORX Countersunk Head Bolt Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

BIGGEST Beast Box

M5 x 12mm Dome Headed TORX Bolt DIN6912 Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt DIN6912 Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 20mm Socket Capped Head TORX Bolt ISO 4762 Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 18mm Grub Screw Marine Grade Stainless Steel - Connects to 80mm HEX Spacer

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M5 x 5mm Black Steel Grub Screw Marine Grade Stainless Steel - Connects into Motor Mount to give Axle position on Mountainboards

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M8 NUT - Flanged & Serated A2 Steel - Marine Grade Stainless steel Nylock Nut

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M4 x 80mm Aluminium Threaded Spacer Nut Used for assembling the BEAST Battery Boxes

Used for assembling the BEAST BATTERY BOX.

x7 Required per box

M4 x 50mm Aluminium Threaded Spacer Nut Used for assemblying the Battery Boxes

Used for assembling the MONSTER BATTERY BOX.

x9 Required per box

19.5mm Cr-Mo BOX AXLE - 12mm

Everybody knows that TRAMPA's amazing equipment is perfect for so many other products & projects other than Electric Mountainboarding & anything from Go-Karts, Drift Trikes, Buggies, Robots have all been made here & there is so much more going on behind the scenes... Its not just the Electric Mountainboarding scene anymore, & as consequence we have become all about modular connect ability, bringing solutions to our own conundrums whilst working alongside lots of other creative individuals or University Teams & even Global companies, & so we realised creating this special 'Fit anywhere AXLE' would be the resolve for many peoples projects & bring so much more help to so many others projects that we have found ourselves involved with....

And so TRAMPA's new 'fit anywhere' 19.5mm TO 12mm Cr-Mo AXLES are compatible with the full range of TRAMPA's Motor Mounts, Drives & Wheels, then Combined with our MOTORS & a VESC 6, the performance is guaranteed & getting your project rolling couldn't be easier!

This 'Fit Anywhere Axle' measures 19.5 x 19.5mm has been specifically made to fit easily inside 25x25x2.5mm box section. If you are creative & have access to a welding machine you can pretty much make anything from 25mm Steel Box section & then installed with our '19.5mm Fit Anywhere Axle' makes it kind of like a giant Mechano set!

The Axle has 3x 'M8 Tapped holes' in its body to allow for a range of easy mounting options. You will need to drill corresponding connecting holes in the 25mm Box section in order to weld or to be able to securely fit the axle with a BOLT KIT.

Other mounting options could include being bolted to sheet material or being welded.

Share your project with us on instagram @TRAMPABOARDS

25x25x2.5mm - Mild Steel 25mm Box Section sold in 10cm Lengths - select in dropdown Below the length you want

Everybody knows that TRAMPA's amazing equipment is perfect for so many other products & projects other than Electric Mountainboarding & anything from Go-Karts, Drift Trikes, Buggies, Robots have all been made here & there is so much more going on behind the scenes... Its not just the Electric Mountainboarding scene anymore, & as consequence we have become all about modular connect ability, bringing solutions to our own conundrums whilst working alongside lots of other creative individuals or University Teams & even Global companies, & so we realised creating this special 'Fit anywhere AXLE' would be the resolve for many peoples projects & bring so much more help to so many others projects that we have found ourselves involved with....

And so TRAMPA's new 'fit anywhere' 19.5mm to 12mm Cr-Mo AXLES are compatible with the full range of TRAMPA's Motor Mounts, Drives & Wheels, then Combined with our MOTORS & a VESC 6, the performance is guaranteed & getting your project rolling couldn't be easier!

This 'Fit Anywhere Axle' measures 19.5 x 19.5mm has been specifically made to fit easily inside 25x25x2.5mm box section. If you are creative & have access to a welding machine you can pretty much make anything from 25mm Steel Box section & then installed with our '19.5mm Fit Anywhere Axle' makes it kind of like a giant Mechano set! You can purchase some lengths of 25mm Box section on this page, please select from the drop down menus below what length you want, we charge £1 per 10cm & always give you more than you ask for.

The Axle has 3x 'M8 Threaded holes' in its body to allow for a range of easy screw in mounting options. You will need to drill corresponding connecting holes in the 25mm Box section in order to weld or to be able to securely fit the axle with a BOLT KIT. The holes should be 20mm apart.

Other mounting options could include being bolted to sheet material or being welded.

Share your project with us on instagram @TRAMPABOARDS

10 INCH Inner Tube INNOVA 10x3 Inch 250x80mm - fits 4 inch Rims & 10 inch tyres

INNOVA's Re-enforced 9 Inch inner tube measures 225mm x 65mm and will fit into all the of the 9 inch Tyres on the TRAMPA website. This 9 Inch Inner Tube will also fit into the tyres of other brands. Being made from slightly thicker rubber, this Inner Tube is slightly heavier than alternatives but the Inner Tube will handle much higher than recommended inflation rates... Therefore this INNOVA inner tube is ideal for heavier or pro riders seeking high inflation pressures...

This INNOVA Inner tube will fit into all known 9 inch tyres as well as most ATB Hubs on the market & it comes as expected with a "Plastic Anti Dust" Valve cap!

Punctures Suck! Its always possible to get a puncture in the environments we ride in, so always carry a spare if you don't want your day spoiling...

PRIMO 3 spoke Hub - Fits the 9 inch stiker tyre

PRIMO's 3 Spoke Composite Hub has a center set bearing position & because of its special '3.75/4 Inch Rim' means it is capable of fitting both 3.75 Inch Rim Tyres (8 Inch Tyres) & 4 Inch Rim Tyres (9 inch Tyres). 

 The 3 Spoke PRIMO hubs are assembled using just 3 heavy duty M6 x 30mm Stainless Steel Socket capped Bolts & M6 Nylock nuts. The Composite hub is very Strong but a bit Chunky. IMO its best fitted with 9 Inch Tyres or Any tyre using a 4 inch Rim.

Because of the extra size of this hub it is strong ebough for many applicatuons. When comparing the weight to the super slim design of the PHATLADS hubs (weighing just 184g), the PRIMO 3 Spoke hub weighing 282g does weigh in a little on the heavy side, but the 3 spoke'd solid structure is a timeless classic with an awesome reputation for not letting you down & is currently the only option hub that TRAMPA offers should you wish to mount 'Center-Set 9 inch Wheels'

Although slightly tighter to fit into than other hubs, TRAMPA's regular 28mm Bearings will fit perfectly into the Bearing housing of the PRIMO hub. As a top tip place the bearings in the freezer for 30 minutes before inserting them into the hub, the cold will cause the metal of the bearing to shrink & fit easier into the hub!

To fit the PRIMO 3 spoke hubs onto the TRAMPA TRUCKS you will need a special 12x 9.5mm Axle Spacer to allow the hub to position onto the axle correctly.

Bearings can be purchased at a discounted price when purchased with Hubs.

INNOVA DURO TREAD 10 Inch Tyre - Suitable for Golf Buggies, Karts, Trikes etc 4x 3x 10 Fits 4 inch Rims only


COMING SOON!!
 

10 Inch Tyres will only fit to the 3 spoke PRIMO Hub or the 9 Inch Deep Dish MEGASTAR Hubs.

Used primarilly outside the princliples of Mountainboarding, these Large tyres can be adapted to fit to all kinds of creations, projects & developments.

The PRIMO & MEGASTAR Hubs with 10 Inch Tyres can be fitted onto 12mm Axles using 12x28x8mm ATB Bearings

TRAMPA's DRIFT-E-TRIKE puts a smile on all the faces that stand in front of it! Just by looking at it you instantly recognize it is a mischievous device & is going to be so much fun to mess around on, so much so that its almost impossible to say how good it is!

Chopped & assembled in the limited spare time we get here at the HQ, the TRAMPA Crew have had so much fun messing around developing the DRIFT-E-TRIKE & DIRT-E-KART over the last 14 months. Ive not seen so much mud on faces in years, so much mud to say that googles are absolutely essential, specially when your thrashing around chasing your mates, splashing through puddles in the woods & ripping up parks like the crew have been up too. Your shaken n bounced n slide around in all directions, sometimes at terrifying speeds & even sometimes going backwards....!! lol 

Currently only available as a Rear Beam conversion kit, it is possible to purchase a Stock Drift Trike everything else you might need to make a conversion from TRAMPA. We can currently supply you the Fully assembled Rear beam with Motor mounts & 9 or 10 inch wheels, Battery Box with VESC 6 controllers, twist throttles, Thumb Brakes, 

Using regular 25mm Mild Steel Box section as the basis for our platform, special parts have been made for easy/fast modular assembly with connection to the full range of TRAMPA motor mounts & related parts.

So, using pretty much all the same equipment as we use for the TRAMPA Spur Gear Drive Mountainboards, but transferred onto a Drift-E-Trike Rear Beam & SGD Motor Mount kit,
We are working on a Frame & forks of course but in the mean time you will You need to purchase a BMX or a decent quality Drift Trike as the foundation to your build & then weld on the kit we send you to the back end of what you already have.....

2x CNC Spring Truck PRO Motor Mount CONNECTOR
2x CNC Spring Truck PRO Motor Mount BACK PLATE
2x Anti Vibration Rubber pads fitting in the Conical Clamps
8x M5x 18mm Marine Grade Stainless Steel HEX Head Bolts
8x M5 Marine Grade Stainless Steel Washers
2x SPUR Gear Drive T6 Tub with TRAMPA Logo
2x TRAMPA SPUR Gear Drive T6 Aluminium Tub Cover
1x SPUR Gear Drive Bash Guard - RIGHT Side
1x SPUR Gear Drive Bash Guard - LEFT Side
6x M4 x 10 Countersunk TORX bolt
2x SPUR Gear Drive Motor Adaptor
8x M4 x 20 Socket Cap TORX Bolt
2x Spur Gear Drive CUSTOM SLAVE Pulley
2x Spur Gear Drive CUSTOM Motor Pulley - c45 HARDENED STEEL
2x M5 x 5mm Black Steel Grub Screw
2x KEYWAY for Motor Pulley & Axle Shaft - 3x 3x 12mm
2x SPUR Gear Drive Hub Adaptor
10x M5 x 12 Dome Headed TORX Bolt
14x M4 x 10 Dome Headed TORX Bolt
1x Motor Protection Housing
1x Motor Fan
5x M3 x 18 Countersunk TORX Bolt
2x ELECTRIC Mountainboard Motor Mount V-Ring TUB Seal
2x 19.5mm Cr-Mo BOX AXLE - 12mm
11x 25x25x2.5mm - Custom Length Of Mild Steel 25mm Box Section
6x M8 x 40 H/T SET Screw BZP
6x M8 NUT - Flanged & Serated A2 Steel
2x 6376 160Kv 3800w DC Brushless & SENSOR-LESS Motor
2x PRIMO 3 spoke Hub - Fits the 9 inch stiker tyre
6x M6 x 30 Socket cap Allen-Key Stainless Steel Bolt
6x M6 Nut - Marine Grade Stainless steel Nylock nut
2x DURO TREAD 10 Inch Tyre 10x 3.5x 4
2x 10 INCH Inner Tube - INNOVA
2x VESC 6 MkVI PCB - The next generation - ORIGINAL
2x VESC 6 CNC Aluminum Heat Sink Silicone Sealed Housing
2x VESC 6 Inner Silicone Seal
2x BLACK Silicon Coated Cable with WHITE TRAMPA Logo - per 10cm
2x RED 1036 Strand 4mm core Silicon Coated Cable with BLACK TRAMPA Logo
2x XT90H-F with Housing - Female
6x 4mm FEMALE Bullet connector - GC4010-F
1x MASSIVE Monster Box BASE for 2WD
1x MASSIVE Monster Box LID
1x MASSIVE Monster Box SIDE PANEL - BLANK LI-PO
1x MASSIVE Monster Box 2mm DOUBLE STACK SIDE PANEL - CHARGER LI-PO
1x MASSIVE Monster Box 2mm DOUBLE STACK SIDE PANEL - BLANK LI-PO
1x MASSIVE Monster Box 2x VESC 6 2mm DOUBLE STACK Mounting Panel (2WD) LI-PO
7x M4 x 10mm Stainless Steel DOME Headed TORX Bolts Monster Box Base Assembly
7x M4 x 80mm Aluminium Hex Spacer - Custom Colour option
7x M4 x 50mm Aluminium Hex Spacer - Custom Colour option
7x M4x16mm Grub Screw to hold the Hex Spacers together
7x M4 x 16mm Stainless Steel Countersunk TORX Bolts Monster Box Lid Bolts
1x Power Switch
1x 16mm Fixing Nut
1x Power Switch Cable Harness
12x Water sealing - OPEN Round Silicone cable Grommets for 4mm Cable
4x Water sealing - Large Oval Spliced Silicone Seals for Balancer cable access
4x Large Round Grommets for allowing sensor cables to pass
Weight: 18,000g
This product cannot be purchased on its own.
menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon