Home»DIRT-E-TRIKE»Dirt-E-Trike Complete Back End Kit

Classic Monster Box DOG BONE is used to mount the Classic Monster box securely to the deck

This is the Classic Monster Box DOG-BONE. 

Made from T6 Alumium the DOG-BONE is used to mount the Classic Monster box securely to the TRAMPA deck.

The DOG-BONE requires 1x Top Rubber Mounting pads, 2x Bottom Rubber Mounting Pads, 4x M6x 25mm Countersunk Bolts & 3x M6x 12mm Countersunk Bolts to connect to the CLASSIC Box to the deck securely & without any rattles.

The DOG-BONE is Sold as a kit in Deck Accessories

CLASSIC MONSTER Box MkV 2WD BASE

The Monsterbox Classic MkV Base connects to all vertical panels in a Monster Box Classic or Double Stack Monster Box Classic, provided the adjacent panels are also Mk5. They are used with grommets to allow entry into the box by the phase and sensor cables, and the edges of the box are where the hex spacers mount. Additionally, the base is where any Monsterbox is mounted to the board. In this case that can be done via the standard bushing system or Dogbone mounting system. This panel is only designed to operate with 2 motors.

TRAMPA CLASSIC Monster Box MKV LID - Battery Side

The Monsterbox Classic MkV Lid rests on top of the side and end panels of the Monsterbox Classic MkV and centers the screws into the hex spacers to hold the box together.

TRAMPA CLASSIC Monster Box MKV LID - VESC Side

The Monsterbox Classic MkV VESC Side Lid rests on top of the side and VESC panels of the Monsterbox Classic MkV and centers the screws into the hex spacers to hold the box together. It also acts as an access terminal, allowing you to conduct simple maintenance such as charging and turning your VESCs on and off without opening up the box.

CLASSIC MONSTER Box MkV 2mm SIDE PANEL

The side panel is a structural component of the Monster Box MkV that connects the lids and base of the box together.

TRAMPA CLASSIC Monster Box MkV END Panel

Structural component, like the side panels, to connect the lids and base of a Monster Box MkV together.

CLASSIC MONSTER Box MkV 2x VESC 6 Mounting Panel

Used for mounting two VESC 6’s on the inside of a Monster Box Classic MkV.

TRAMPA CLASSIC Monster Box MKV Inspection Pit

The Inspection Pit allows easy access to balance leads and other items on the Monster Box Classic MkV.

TRAMPA CLASSIC Monster Box MKV Inspection Pit Lid

The Inspection Pit lid covers and secures the Inspection Pit on the Monster Box Classic MkV.

10cm of RED 4mm core 1036 Strand Silicon Coated Cable

Allow your Electric board to gain the maximum performance by fitting the very highest quality Electrical Cables & Connectors and let the power in your battery flood out as performance at the rear wheels!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn in production to produce to such a small amount of such a high quality cable, but finally TRAMPA has had what it wanted delivered & we can now supply you with Super high Quality Silicon Cables in RED or BLACK with co-orinating BLACK & WHITE TRAMPA logos to prove the quality & show off the kind of performance your board is capable of! :-)

TRAMPA's gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. The Blaff cables have enclosed in the Besilen insulated​ Silicon Outer sleeve, 1800 Highly flexible TOP QUALITY Copper strands in the center... BLAFF cable is used for the highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation (Trains, Trams, Planes) as they have a global reputation of incredible high standards.

TRAMPA Silicon cables solder perfectly into XT60 & XT90 connectors to give the perfect connection to your power source. A soldering service for a pair of cables is available though TRAMPA when you purchase the cables as pairs,

RED Silicon Casing with contrasting BLACK TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

10cm of RED 4mm core 1036 Strand Silicon Coated Cable

Allow your Electric board to gain the maximum performance by fitting the very highest quality Electrical Cables & Connectors and let the power in your battery flood out as performance at the rear wheels!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn in production to produce to such a small amount of such a high quality cable, but finally TRAMPA has had what it wanted delivered & we can now supply you with Super high Quality Silicon Cables in RED or BLACK with co-orinating BLACK & WHITE TRAMPA logos to prove the quality & show off the kind of performance your board is capable of! :-)

TRAMPA's gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. The Blaff cables have enclosed in the Besilen insulated​ Silicon Outer sleeve, 1800 Highly flexible TOP QUALITY Copper strands in the center... BLAFF cable is used for the highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation (Trains, Trams, Planes) as they have a global reputation of incredible high standards.

TRAMPA Silicon cables solder perfectly into XT60 & XT90 connectors to give the perfect connection to your power source. A soldering service for a pair of cables is available though TRAMPA when you purchase the cables as pairs,

RED Silicon Casing with contrasting BLACK TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

10cm of BLACK 4mm core 1036 Strand Silicon Coated TRAMPA Logo'd Cable

Allow your Electric board to gain the maximum performance by only fitting the very highest quality Electrical Cables & Connectors to let the power in your battery flood out as performance at the wheel!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn to produce to such a small amount of cable at such a high quality standard, but finally TRAMPA has got what it wanted & has now taken delivery of its own Super high Quality Silicon Cables in RED & BLACK with contrasting Black & White TRAMPA logos to prove the quality & show off the kind of performance your board is harvesting! :-)

TRAMPA's Gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. BLAFF cable is used for highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation and the likes (Trains, Trams, Planes) as they have a global reputation of incredible high standards. 

Enclosed in the Besilen insulated​ Silicon Outer lies 1800 Highly flexible TOP QUALITY Copper strands in the center...

BLACK Silicon Casing with contrasting WHITE TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

10cm of BLACK 4mm core 1036 Strand Silicon Coated TRAMPA Logo'd Cable

Allow your Electric board to gain the maximum performance by only fitting the very highest quality Electrical Cables & Connectors to let the power in your battery flood out as performance at the wheel!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn to produce to such a small amount of cable at such a high quality standard, but finally TRAMPA has got what it wanted & has now taken delivery of its own Super high Quality Silicon Cables in RED & BLACK with contrasting Black & White TRAMPA logos to prove the quality & show off the kind of performance your board is harvesting! :-)

TRAMPA's Gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. BLAFF cable is used for highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation and the likes (Trains, Trams, Planes) as they have a global reputation of incredible high standards. 

Enclosed in the Besilen insulated​ Silicon Outer lies 1800 Highly flexible TOP QUALITY Copper strands in the center...

BLACK Silicon Casing with contrasting WHITE TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

XT90H-M connector - Male

On most TRAMPA electrical components, you’ll find AMASS XT90 connectors.  With a strong nylon plastic body & cylindrical brass contacts that comfortably fit 10-12 gauge wires, XT90 connectors are rated to handle 90 Amps continuous – but have been tested up to 270A!

Available as standard, or Anti-Spark - we recommend Anti-Spark for connections that are likely to be plugged/unplugged often.

JST - 2.0mm Header Top Entry 2 pin - Motor Temp Sensor - MALE

This 6 pin Male connector is used to extend the motor hall sensor cables from the motor going to the VESC. 

JST - 2.0mm Header Top Entry 2 pin - Motor Temp Sensor - MALE

This 6 pin Male connector is used to extend the motor hall sensor cables from the motor going to the VESC. 

TRAMPA Custom DC Motor 6364 6376 6386 - SINGLE

TRAMPA Custom Single motor 6364 160Kv or 6376 wound in 160Kv or 185Kv configurations.

TRAMPA's very own purpose made 160 KV 6376 Out-Runner Motor provides 160RPM per volt. CUSTOM MADE to handle HIGH Power outputs.

This Motor has many NEW features that increase both hardiness & efficiency!

- Improved thermal design; with a more thermally-connected-mass, heat can dissipate much more efficiently. The new Rotor bodies feature raised rings that increase surface area, further helping heat dissipation.

- Stronger Hardware; larger & stronger bolts have been used throughout the motor, improving the motor’s strength & sturdiness, while making maintenance a lot less fiddle-y.

- Optimised Air-cooling; Stator cooling via air-flow - larger openings on the stator & having no sensor PCB both help to encourage a cooling flow of air through the motor. Further improve the air-flow using the MKII Motor Housing & Fan End-cap Kit.    

- Accurate & faster temperature readings; With a heat sensor glued to the copper windings in the ideal location, it's possible to get faster and more accurate motor-temp readings, which is important for future sensorless startup algorithms.

- Optimised for sensorless rotor position detection; With no sensor PCB inside, this motor works best when used with a VESC Speed Controller featuring Advanced Sensorless Startup - when paired & activated the motor will be able to reach full torque at 0RMP! 

All TRAMPA Motors use Premium high-temperature Copper & the highest grade of Neodymium Magnets available. The magnets connect to an Extended & Heat treated 8mm Steel Axle shaft that's locked in a balanced position with 4 precision Bearings. All screws & fixings used in the assembly are Marine grade Stainless Steel. All creating super-tough  motors that can easily out-perform the competition!

Our special design allows you to fit mesh filters, or entire Motor housings, preventing the impregnation of particles entering in the motor & stopping them running smoothly. The motor Stators are equipped with twelve M4 threaded mounting holes, sitting on a 44mm diameter circle. The extra holes allow the motor to be mounted at the exact angle needed so the motor cables always sit in the perfect angle, towards the mount or deck.

Using 38.5mm x 8mm Heat-Treated Hardened-Steel Motor Shaft (fitted with a 12x3x3mm KEYWAY locator as standard), the extra length of the Axle allows us to add adequate support with Motor Axle Supports, & allows us to fit  Extra wide Motor Pulleys for the 15 - 20mm wide HTD 5M STRONGBELTs we use as standard, guaranteeing a much stronger power delivery.

Two 3x3x12mm KEYWAYs lock the Axle shaft at both ends (1 to the Rotor & 1 to the Motor Pulley), eliminating any & all "Motor slip", & providing maximum performance to the rider, while gaining critical data for the VESC speed controller.

The Heavy Duty & high quality power cables use 4mm Gold Plated Bullet Connectors to connect to a power source. 

Aluminium Star Shaped Motor Filter Holder for all 63mm size Motors

The Motor Star Holder is a critical piece of Trampa motors - it holds in place the filter at the end of the motor casing keeping dust and debris out so you can ride longer!

Stainless Steel Motor Filter is Held in place using the Motor filter holder

This Stainless Steel 'Motor END FILTER' fits into the end of any of TRAMPA's motors,

Fitting filters to your motors prevents dust n debris from entering the motor whilst still allowing cool air enter & pass though, encouraging cool operating temperatures.

This circular Stainless Steel Filter is pre-punched with the fixing holes to fit to all TRAMPA Motors. It requires the STAR SHAPED ALUMINUM END FILTER HOLDER to secure the end filter into place, whilst M3x4mm Dome Headed bolts screw through the star holder & filter turning directly into the end of the motor.

Stainless Steel Motor filter wraps around the CAN of the 63mm TRAMPA motors preventing dust n debris from entering the motor

This Stainless Steel WRAP Around Motor filter wraps around the CAN or BASE of any of TRAMPA's motors,

There are air cooling holes in the base of TRAMPA's motors to encourage cool air to enter to keep the motor running cool, prolongiung maximum throttle! The stainless filters prevent dust n debris from entering the motor whilst still allowing cool air enter & pass though.

The WRAP Around Stainless Filter has fixing holes pre-punched into it. During installation the filter should be folded in half. This is best done over a firm accurate straight line such as a metal ruler. Once the filter is folded in half it is double thickness & therefore double filtered...

Using tiny M3x4mm Dome Headed Allen Key bolts & a tiny amount of non permenant Lock Tight to stop them running out, pass the little bolts though the pre-punched fixing holes in the filter & stretching the filter into a tight position & screw directly into the can of the motor.

This filter fits all TRAMPA Motors & is best used in conjunction with the Motor END FILTER & ALUMINUM END FILTER HOLDER that secures the end filter in place

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x12mm

TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.

TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....

SPUR Gear Drive T6 Tub with TRAMPA Logo

CNC’d from a solid block of T6 heat-treated Aluminium, the SPUR GEAR DRIVE HOUSING is as strong as it is sleek. When paired with the CNC’d TUB COVER, the completed housing keeps the elements outs, the gears & belts clean & dry, & the whole board riding smoothly.
Designed to tightly slip around the CNC’d Hangers on Precision Vertigo Trucks, the Tub locks the entire drivetrain is accurately & securely in line.
With a bash-guard integrated into its design, you can be confident the tub will survive all the knocks-&-bumps its bound to receive on a ride.
Fits 10-tooth Straight or Helical Motor Pulleys & 58-tooth Helical or 59-tooth Straight-cut slave pulleys.
The Housing is perfectly symmetrical, allowing it to slide onto left or right drive trains.
 

TRAMPA SPUR Gear Drive T6 Aluminium Tub Cover

The Spur Gear Tub Cover is crucial to keeping your drive system free of dirt & debris. CNC’d from Premium Aluminium, giving it the perfect weight: strength ratio, the cover slots tightly over the Spur Gear tub, sealing off the drive system & leaving room for the Hub Adaptor & Rubber Seal. 

SPUR Gear Drive Bash Guard - RIGHT Side

Made using hardened steel, the spur gear bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the right drivetrain.

SPUR Gear Drive Bash Guard - LEFT Side

Made using hardened steel, the spur gear bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the left drivetrain.

SPUR Gear Drive Motor Adaptor

Housing a precision bearing for Motor Axle Support the SPUR GEAR DRIVE Motor Adaptor is used for attaching the motor securely to the drivetrain.
Precision CNC’d from hardened steel, the Motor Adaptor also allows for the use of PRO MOTOR HOUSING.

SPUR Gear Drive Hub Adaptor

The Hub Adaptor attaches the Slave Pulley to the Hubs, delivering the power of the motors to the wheels. Connects to SUPERSTAR or MEGASTAR hubs.

Precision CNC’d from Hardened Steel.

Connects to Slave Pulley using 5x m5x12mm Torx head screws.

Spur Gear Drive 57 Tooth 17.5º HELICAL Slave Pulley - c45 Hardened Steel

Spur Gear Drives are compatible with Straight-cut or Helical Gears.
CNC’d from hardened steel, the 58-tooth Helical Slave Pulley pairs with the 10-tooth Helical Motor Pulley, giving a gear ratio of 1:5.8. Compared to the 59-tooth Straight-cut Slave Pulley’s ratio of 1:5.9, Helical gears will ultimately have a higher top speed.  

Helical Gears provide more surface contact between the teeth, resulting in a smoother & quieter ride.

Straight-cut Gears are the cheaper option – still providing amazing torque & performance, while running a bit louder than helical.   

Connects to Hub Adaptor using 5x m5 x 12mm Torx head screws.

Spur Gear Drive 10 Tooth 17.5º HELICAL Cut motor Pulley - c45 HARDENED Steel Nitriding

10-Tooth helical-cut Motor Pulley for Spur Gear Drive

Helical Gears provide more surface contact between the teeth, resulting in a smoother & quieter ride.

Mountainboard Motor Mount V-Ring TUB Seals - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

Mountainboard Motor Mount Truck Connector

Works with PRO BELT & SPUR GEAR Drives.
The Clamp housing slips over the axels of Precision CNC’d Vertigo Trucks, ensuring the drivetrain sits at the correct angle.
Working in conjunction with the Conical Clamp, when connected together the housing squeezes the clamp to the hanger, securely attaching the drivetrain to the trucks.

Precision CNC’d from T6 Heat-treated Aluminium.

Mountainboard Motor Mount Connector Conical Clamp

Works with PRO BELT & SPUR GEAR Drives.

Designed to work in conjunction & attach securely to Precision CNC’d VERTIGO trucks, the Conical Clamp slips tightly over the CNC’d square on the hanger of the trucks. When attached to the Clamp Housing, the Conical Clamp tightens around the hanger, ensuring secure & accurate Motor Mount attachment.

Precision CNC’d from T6 Heat-treated Aluminium.

Mountainboard Motor Mount Rubber pad for Conical Clamps - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

M3 x 4mm Dome Headed Head Allen-Key Bolt DIN6912 Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

This Bolt is DOME HEADED, meaning that when screwed into position it sits low & neatly over the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-TRAMPA MOTORS

M6 x 50mm Socket Capped Allen-Key Bolt for primo hub - Marine Grade Stainless steel

TRAMPA's M6 x 30mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the PRIMO 3 Spoke Hubs. The socket capped head of the Bolt screws neatly though the HUB eventually screwing into the Marine Grade Stainless Steel M6 Nylock Nut on the other side of the hub. 

Weighing just 8 grams each, these Bolts are lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers nuts & bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You’ll will need a 5mm Allen Key  to tighten & loosen the Bolt from the nut. Ensure all your Nuts & Bolts are tight before riding!

M8 x 60mm Socket Capped Allen-Key Bolt for primo hub - Marine Grade Stainless steel - Black Steel

TRAMPA's M6 x 30mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the PRIMO 3 Spoke Hubs. The socket capped head of the Bolt screws neatly though the HUB eventually screwing into the Marine Grade Stainless Steel M6 Nylock Nut on the other side of the hub. 

Weighing just 8 grams each, these Bolts are lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers nuts & bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You’ll will need a 5mm Allen Key  to tighten & loosen the Bolt from the nut. Ensure all your Nuts & Bolts are tight before riding!

M5 x 20mm Regular Hex Head Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M5 x 10mm TORX Countersunk Bolt - Marine Grade Stainless steel with TORX Fitting

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M6 x 12mm TORX Countersunk Head Bolt Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

BIGGEST Beast Box

M5 x 12mm Dome Headed TORX Bolt DIN6912 Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 20mm Socket Capped Head TORX Bolt ISO 4762 Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M5 x 5mm Black Steel Grub Screw Marine Grade Stainless Steel - Connects into Motor Mount to give Axle position on Mountainboards

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M8 NUT - Flanged & Serated A2 Steel - Marine Grade Stainless steel Nylock Nut

M8 Flanged Scerated Nikle plated Steel nut

M8 NUT - Flanged & Serated A2 Steel - Marine Grade Stainless steel Nylock Nut

M8 Flanged Scerated Nikle plated Steel nut

7/16ths Nut - Marine Grade Stainless steel Nylock Axle HALF nut (W7/16-20T UNF) - Fits to 12mm Axles

This very special 7/16_^ths of an inch Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut.. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore further reducing weight in the Truck! A few Grams here & a few grams there soon adds up & makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area, where a few grams makes all the difference...

This very special 3/8_^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W7/16 - 20T - UNF. This Nut is used to hold the wheels onto the axles of the Spring Trucks fitted with 12mm axles. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 16mm or 5/8th_^ths of an Inch spanner to tighten / loosen the Nut onto the Axle or Kingpin. Do not overtighten the nut & make sure the wheel can spin freely but does not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

19.5mm Cr-Mo BOX AXLE - 12mm

Everybody knows that TRAMPA's amazing equipment is perfect for so many other products & projects other than Electric Mountainboarding & anything from Go-Karts, Drift Trikes, Buggies, Robots have all been made here & there is so much more going on behind the scenes... Its not just the Electric Mountainboarding scene anymore, & as consequence we have become all about modular connect ability, bringing solutions to our own conundrums whilst working alongside lots of other creative individuals or University Teams & even Global companies, & so we realised creating this special 'Fit anywhere AXLE' would be the resolve for many peoples projects & bring so much more help to so many others projects that we have found ourselves involved with....

And so TRAMPA's new 'fit anywhere' 19.5mm TO 12mm Cr-Mo AXLES are compatible with the full range of TRAMPA's Motor Mounts, Drives & Wheels, then Combined with our MOTORS & a VESC 6, the performance is guaranteed & getting your project rolling couldn't be easier!

This 'Fit Anywhere Axle' measures 19.5 x 19.5mm & has been specifically made to fit easily inside 25x25x2.5mm box section. If you are creative & have access to a welding machine you can pretty much make anything from 25mm Steel Box section & then installed with our '19.5mm Fit Anywhere Axle' makes it kind of like a giant Mechano set!

The Axle has 3x 'M8 Tapped holes' in its body to allow for a range of easy mounting options. You will need to drill corresponding connecting holes in the 25mm Box section in order to weld or to be able to securely fit the axle with a BOLT KIT.

Other mounting options could include being bolted to sheet material or being welded.

Share your project with us on instagram @TRAMPABOARDS

25x25x2.5mm - Mild Steel 25mm Box Section sold in 10cm Lengths - select in dropdown Below the length you want

Everybody knows that TRAMPA's amazing equipment is perfect for so many other products & projects other than Electric Mountainboarding & anything from Go-Karts, Drift Trikes, Buggies, Robots have all been made here & there is so much more going on behind the scenes... Its not just the Electric Mountainboarding scene anymore, & as consequence we have become all about modular connect ability, bringing solutions to our own conundrums whilst working alongside lots of other creative individuals or University Teams & even Global companies, & so we realised creating this special 'Fit anywhere AXLE' would be the resolve for many peoples projects & bring so much more help to so many others projects that we have found ourselves involved with....

And so TRAMPA's new 'fit anywhere' 19.5mm to 12mm Cr-Mo AXLES are compatible with the full range of TRAMPA's Motor Mounts, Drives & Wheels, then Combined with our MOTORS & a VESC 6, the performance is guaranteed & getting your project rolling couldn't be easier!

This 'Fit Anywhere Axle' measures 19.5 x 19.5mm & has been specifically made to fit easily inside 25x25x2.5mm box section. If you are creative & have access to a welding machine you can pretty much make anything from 25mm Steel Box section & then installed with our '19.5mm Fit Anywhere Axle' makes it kind of like a giant Mechano set! You can purchase some lengths of 25mm Box section on this page, please select from the drop down menus below what length you want, we charge £1 per 10cm & always give you more than you ask for.

The Axle has 3x 'M8 Threaded holes' in its body to allow for a range of easy screw in mounting options. You will need to drill corresponding connecting holes in the 25mm Box section in order to weld or to be able to securely fit the axle with a BOLT KIT. The holes should be 20mm apart.

Other mounting options could include being bolted to sheet material or being welded.

Share your project with us on instagram @TRAMPABOARDS

30x30x2.5mm - Mild Steel 25mm Box Section sold in 10cm Lengths - select in dropdown Below the length you want

Everybody knows that TRAMPA's amazing equipment is perfect for so many other products & projects other than Electric Mountainboarding & anything from Go-Karts, Drift Trikes, Buggies, Robots have all been made here & there is so much more going on behind the scenes... Its not just the Electric Mountainboarding scene anymore, & as consequence we have become all about modular connect ability, bringing solutions to our own conundrums whilst working alongside lots of other creative individuals or University Teams & even Global companies, & so we realised creating this special 'Fit anywhere AXLE' would be the resolve for many peoples projects & bring so much more help to so many others projects that we have found ourselves involved with....

And so TRAMPA's new 'fit anywhere' 19.5mm to 12mm Cr-Mo AXLES are compatible with the full range of TRAMPA's Motor Mounts, Drives & Wheels, then Combined with our MOTORS & a VESC 6, the performance is guaranteed & getting your project rolling couldn't be easier!

This 'Fit Anywhere Axle' measures 19.5 x 19.5mm & has been specifically made to fit easily inside 25x25x2.5mm box section. If you are creative & have access to a welding machine you can pretty much make anything from 25mm Steel Box section & then installed with our '19.5mm Fit Anywhere Axle' makes it kind of like a giant Mechano set! You can purchase some lengths of 25mm Box section on this page, please select from the drop down menus below what length you want, we charge £1 per 10cm & always give you more than you ask for.

The Axle has 3x 'M8 Threaded holes' in its body to allow for a range of easy screw in mounting options. You will need to drill corresponding connecting holes in the 25mm Box section in order to weld or to be able to securely fit the axle with a BOLT KIT. The holes should be 20mm apart.

Other mounting options could include being bolted to sheet material or being welded.

Share your project with us on instagram @TRAMPABOARDS

STEEL Kingpin M6x 8mm x 80mm for Spring Truck - Heavy Duty 12.9 Steel

This M8 x 80mm STAINLESS STEEL Spring Truck Kingpin is used to connect the Hanger & the Baseplate on any of TRAMPA's Spring Trucks.

Using high quality metals & sizing down to a 8mm Kingpin, we have managed to save loads of weight whilst retaining all the strength necessary for the job!

This M8 x 80mm Kingpin uses an 8mm Washer to support the busing from the outside & a 6mm washer to protect the bushing on the inside side & connects into an M6 Nut. You'll need a 4mm Allen key to hold the Kingpin & a 10mm spanner to tighten/loosen your M6 Kingpin Nut.

This Kingpin pushes through plastic bushings before being placed into position in the Truck System. The Plastic bushings allow the metal parts (Hanger & Baseplate) to move freely inside each other without allowing the metal parts to touch or wear out.

The plastic bushings will wear out over time & use & will eventually perish & need replacing. SO, make sure your Bushings are always in good working order after riding riding or when upgrading your Kingpin, it might be time to replace them too due to the unavoidable wear & tear of moving mountainboard parts.

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

8 Inch Inner Tube PRIMO 8x2 inch 200x50mm - fits 3.75 inch Rims & 8 inch tyres

PRIMO's own 8 Inch Inner Tube has dimensions of 200mm (outer diameter) x 50mm (width) & will fit into all known 8 inch Tyres & ATB hubs on the market!

The CST PRIMO Inner Tube incorporates slightly thicker rubber into its manufacture process which means the tube is slightly heavier than alternatives but does allow the rider to inflate slightly higher. This extra thickness also gives some extra resistance to punctures, but punctures suck, so always carry a spare inner tube when you are riding as you never know when you might get one.  

The PRIMO Tube uses a 90º Brass Inflation valve which will not rust on you & comes as you would expected with a plastic "anti dust" valve cap!

STICKIES Longboard & Street Carver Wheel Super High Rebound 83 x 52mm

TRAMPA's incredible range of STICKIES Longboard Wheels have taken the world of Longboarding by storm! Produced using the highest grade of Ultra Premium Urethane, and available in either 83 or 90mm size options with a varying range of suitably colour co-ordinatied Urethane Hardnesses, the variety compliments all the different types of rider, covering all the different aspects of street riding. You will be pleased to learn STICKIES Longboard Wheels will fit to ALL Longboard, Street-board & Skateboard Trucks using 8 or 9.525mm Axles.

The re-enforced VENTED CORE of the STICKIES Wheel houses a Center-set bearing position. For those that don't know this means the bearings are housed centrally within the wheel. Being center-set ensure an even wear rate to the wheel ensuring maximum grip at all times, whilst guaranteeing a balanced "high speed spin-rate", thus making turning/sliding as predictable as possible! Not only does the vented core reduce weight, but it also increases airflow around the Bearings ensuring lower operating temperatures when running at high speeds...

The Vented Core also has an extra application... The Venting holes can be used in conjunction with a centering ring & some M4x40mm Socket Capped Bolts to lock into position, either a 33 or 37 Tooth Slave Wheel, to which the complete assembly can be connected to many applications using an electric motor, including the new TRAMPA Electric Longboards & Electric Street-Carver boards as well as many other products due onto the market soon!

Smothering the Vented Core of the STICKIES Longboard wheel is thick PREMIUM URETHANE. Choosing STICKIES will enable you to Carve & Turn like you have only ever dreamed of before, especially when mounted to the new TRAMPA Mini Spring Trucks which happen to turn & carve like nothing else! STIKIES Wheels will also fit to the new 12FIFTIES Trucks and all 8mm Longboard trucks on the Market.

The edges of all the STICKIES wheels are beautifully rounded allowing smooth transitional turns, whilst helping to avoid chipping & cracks at the same time. The rounded edge of the STICKIES wheel gives an overall contact surface of 50mm! Orbiting the outer edge of the BLUE STICKIES WHEEL is a coordinating BLACK TRAMPA logo.

STICKIES will accept regular skate size 608 2RS (8 x 22 x 7mm) bearings & made special for the TRAMPA Mini Spring Trucks, the R6 2RS (9.525 x 22,225 x 7.14mm) Bearings. All of TRAMPA's Longboard/Streetboard bearings are ABEC 7-9 rated & are designed for prolonged high speed use.