This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

Electric TRIKE - TRAMPA's Dirt-E-Trike - CUSTOM build your Trike! If you already have a TRAMPA, you can exchange your batteries, wheels, charger from Board to Trike to keep costs down

Mountainboard Spur Gear Drive TWIN Motor Mount with PULLEYs - NO Motor, NO Filters

Original Spur Gear Drive 10/58 10º HELICAL POM Pulley Kit fits to SUPERSTAR PHATLADS or MEGASTARS

1x Custom TRAMPA DC Motor with BASIC Filters included

21700 2WD Mk II MASSIVE MONSTER Box with 2x VESC 6 Mounting Panel

VESC 6 MkVI - TRAMPA gives you Maximum power!

Drift-E-Trike complete Trike CABLE KIT - STANDARD

RRP
£1,335+

MANUALS
GEARING
PARTS USED
DESCRIPTION
PURCHASE

Mk II MASSIVE Monster Box BASE for 2WD

The Massive Monsterbox Base connects to all vertical panels in a Massive Monster Box or Double Stack Massive Monster Box. They are used with grommets to allow entry into the box by the phase and sensor cables, and the edges of the box are where the hex spacers mount. Additionally, the base is where any Monsterbox is mounted to the board. In this case that can be done via the standard bushing system or Dogbone mounting system. This panel is only designed to operate with 2 motors.

Mk II MASSIVE Monster Box LID

The Massive Monsterbox MkV Lid rests on top of the side and end panels of the Massive Monsterbox MkV and centers the screws into the hex spacers to hold the box together.

Mk II MASSIVE Monster Box SIDE PANEL - BLANK LI-PO

The side panel is a structural component of the Massive Monster Box that connects the lids and base of the box together.

Mk II MASSIVE Monster Box SIDE PANEL - CHARGER LI-PO

The Charging side panel is a structural component of the Massive Monster Box that connects the lids and base of the box together. It has cutouts for easy charging and an On/Off Switch.

Mk II MASSIVE Monster Box 2mm END PANEL - LI-PO

Structural component, like the side panels, to connect the lids and base of a Massive Monster Box together.

Mk II MASSIVE Monster Box 2x VESC 6 2mm Mounting PANEL (2WD) - LI-PO

Used for mounting two VESC 6’s on the inside of a Massive Monster Box.

10cm of RED 4mm core 1036 Strand Silicon Coated Cable

Allow your Electric board to gain the maximum performance by fitting the very highest quality Electrical Cables & Connectors and let the power in your battery flood out as performance at the rear wheels!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn in production to produce to such a small amount of such a high quality cable, but finally TRAMPA has had what it wanted delivered & we can now supply you with Super high Quality Silicon Cables in RED or BLACK with co-orinating BLACK & WHITE TRAMPA logos to prove the quality & show off the kind of performance your board is capable of! :-)

TRAMPA's gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. The Blaff cables have enclosed in the Besilen insulated Silicon Outer sleeve, 1800 Highly flexible TOP QUALITY Copper strands in the center... BLAFF cable is used for the highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation (Trains, Trams, Planes) as they have a global reputation of incredible high standards.

TRAMPA Silicon cables solder perfectly into XT60 & XT90 connectors to give the perfect connection to your power source. A soldering service for a pair of cables is available though TRAMPA when you purchase the cables as pairs,

RED Silicon Casing with contrasting BLACK TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

10cm of BLACK 4mm core 1036 Strand Silicon Coated TRAMPA Logo'd Cable

Allow your Electric board to gain the maximum performance by only fitting the very highest quality Electrical Cables & Connectors to let the power in your battery flood out as performance at the wheel!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn to produce to such a small amount of cable at such a high quality standard, but finally TRAMPA has got what it wanted & has now taken delivery of its own Super high Quality Silicon Cables in RED & BLACK with contrasting Black & White TRAMPA logos to prove the quality & show off the kind of performance your board is harvesting! :-)

TRAMPA's Gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. BLAFF cable is used for highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation and the likes (Trains, Trams, Planes) as they have a global reputation of incredible high standards.

Enclosed in the Besilen insulated Silicon Outer lies 1800 Highly flexible TOP QUALITY Copper strands in the center...

BLACK Silicon Casing with contrasting WHITE TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

10cm of RED 4mm core 1036 Strand Silicon Coated Cable

XT90H-M connector - Male

On most TRAMPA electrical components, you’ll find AMASS XT90 connectors. With a strong nylon plastic body & cylindrical brass contacts that comfortably fit 10-12 gauge wires, XT90 connectors are rated to handle 90 Amps continuous – but have been tested up to 270A!

Available as standard, or Anti-Spark - we recommend Anti-Spark for connections that are likely to be plugged/unplugged often.

TRAMPA Custom DC Motor 6364 6376 6386 - SINGLE

TRAMPA Custom Single motor 6364 160Kv or 6376 wound in 160Kv or 185Kv configurations.

TRAMPA's very own purpose made 160 KV 6376 Out-Runner Motor provides 160RPM per volt. CUSTOM MADE to handle HIGH Power outputs.

This Motor has many NEW features that increase both hardiness & efficiency!

- Improved thermal design; with a more thermally-connected-mass, heat can dissipate much more efficiently. The new Rotor bodies feature raised rings that increase surface area, further helping heat dissipation.

- Stronger Hardware; larger & stronger bolts have been used throughout the motor, improving the motor’s strength & sturdiness, while making maintenance a lot less fiddle-y.

- Optimised Air-cooling; Stator cooling via air-flow - larger openings on the stator & having no sensor PCB both help to encourage a cooling flow of air through the motor. Further improve the air-flow using the MKII Motor Housing & Fan End-cap Kit.

- Accurate & faster temperature readings; With a heat sensor glued to the copper windings in the ideal location, it's possible to get faster and more accurate motor-temp readings, which is important for future sensorless startup algorithms.

- Optimised for sensorless rotor position detection; With no sensor PCB inside, this motor works best when used with a VESC Speed Controller featuring Advanced Sensorless Startup - when paired & activated the motor will be able to reach full torque at 0RMP!

All TRAMPA Motors use Premium high-temperature Copper & the highest grade of Neodymium Magnets available. The magnets connect to an Extended & Heat treated 8mm Steel Axle shaft that's locked in a balanced position with 4 precision Bearings. All screws & fixings used in the assembly are Marine grade Stainless Steel. All creating super-tough motors that can easily out-perform the competition!

Our special design allows you to fit mesh filters, or entire Motor housings, preventing the impregnation of particles entering in the motor & stopping them running smoothly. The motor Stators are equipped with twelve M4 threaded mounting holes, sitting on a 44mm diameter circle. The extra holes allow the motor to be mounted at the exact angle needed so the motor cables always sit in the perfect angle, towards the mount or deck.

Using 38.5mm x 8mm Heat-Treated Hardened-Steel Motor Shaft (fitted with a 12x3x3mm KEYWAY locator as standard), the extra length of the Axle allows us to add adequate support with Motor Axle Supports, & allows us to fit Extra wide Motor Pulleys for the 15 - 20mm wide HTD 5M STRONGBELTs we use as standard, guaranteeing a much stronger power delivery.

Two 3x3x12mm KEYWAYs lock the Axle shaft at both ends (1 to the Rotor & 1 to the Motor Pulley), eliminating any & all "Motor slip", & providing maximum performance to the rider, while gaining critical data for the VESC speed controller.

The Heavy Duty & high quality power cables use 4mm Gold Plated Bullet Connectors to connect to a power source.

Aluminium Star Shaped Motor Filter Holder for all 63mm size Motors

The Motor Star Holder is a critical piece of Trampa motors - it holds in place the filter at the end of the motor casing keeping dust and debris out so you can ride longer!

Stainless Steel Motor Filter is Held in place using the Motor filter holder

This Stainless Steel 'Motor END FILTER' fits into the end of any of TRAMPA's motors,

Fitting filters to your motors prevents dust n debris from entering the motor whilst still allowing cool air enter & pass though, encouraging cool operating temperatures.

This circular Stainless Steel Filter is pre-punched with the fixing holes to fit to all TRAMPA Motors. It requires the STAR SHAPED ALUMINUM END FILTER HOLDER to secure the end filter into place, whilst M3x4mm Dome Headed bolts screw through the star holder & filter turning directly into the end of the motor.

Stainless Steel Motor filter wraps around the CAN of the 63mm TRAMPA motors preventing dust n debris from entering the motor

This Stainless Steel WRAP Around Motor filter wraps around the CAN or BASE of any of TRAMPA's motors,

There are air cooling holes in the base of TRAMPA's motors to encourage cool air to enter to keep the motor running cool, prolongiung maximum throttle! The stainless filters prevent dust n debris from entering the motor whilst still allowing cool air enter & pass though.

The WRAP Around Stainless Filter has fixing holes pre-punched into it. During installation the filter should be folded in half. This is best done over a firm accurate straight line such as a metal ruler. Once the filter is folded in half it is double thickness & therefore double filtered...

Using tiny M3x4mm Dome Headed Allen Key bolts & a tiny amount of non permenant Lock Tight to stop them running out, pass the little bolts though the pre-punched fixing holes in the filter & stretching the filter into a tight position & screw directly into the can of the motor.

This filter fits all TRAMPA Motors & is best used in conjunction with the Motor END FILTER & ALUMINUM END FILTER HOLDER that secures the end filter in place

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x12mm

TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.

TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x12mm

VESC 6 CNC Aluminum Heat Sink Silicone Sealed Housing

CNC T6 Aluminum box Houses the VESC 6 perfectly

Measures 75 x 70 x 18mm

SPUR Gear Drive T6 Tub with TRAMPA Logo

CNC’d from a solid block of T6 heat-treated Aluminium, the SPUR GEAR DRIVE HOUSING is as strong as it is sleek. When paired with the CNC’d TUB COVER, the completed housing keeps the elements outs, the gears & belts clean & dry, & the whole board riding smoothly.
Designed to tightly slip around the CNC’d Hangers on Precision Vertigo Trucks, the Tub locks the entire drivetrain is accurately & securely in line.
With a bash-guard integrated into its design, you can be confident the tub will survive all the knocks-&-bumps its bound to receive on a ride.
Fits 10-tooth Straight or Helical Motor Pulleys & 58-tooth Helical or 59-tooth Straight-cut slave pulleys.
The Housing is perfectly symmetrical, allowing it to slide onto left or right drive trains.

TRAMPA SPUR Gear Drive T6 Aluminium Tub Cover

The Spur Gear Tub Cover is crucial to keeping your drive system free of dirt & debris. CNC’d from Premium Aluminium, giving it the perfect weight: strength ratio, the cover slots tightly over the Spur Gear tub, sealing off the drive system & leaving room for the Hub Adaptor & Rubber Seal.

SPUR Gear Drive Bash Guard - RIGHT Side

Made using hardened steel, the spur gear bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the right drivetrain.

SPUR Gear Drive Bash Guard - LEFT Side

Made using hardened steel, the spur gear bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the left drivetrain.

SPUR Gear Drive Motor Adaptor

Housing a precision bearing for Motor Axle Support the SPUR GEAR DRIVE Motor Adaptor is used for attaching the motor securely to the drivetrain.
Precision CNC’d from hardened steel, the Motor Adaptor also allows for the use of PRO MOTOR HOUSING.

SPUR Gear Drive Hub Adaptor

The Hub Adaptor attaches the Slave Pulley to the Hubs, delivering the power of the motors to the wheels. Connects to SUPERSTAR or MEGASTAR hubs.

Precision CNC’d from Hardened Steel.

Connects to Slave Pulley using 5x m5x12mm Torx head screws.

Spur Gear Drive 58 Tooth 10º HELICAL Cut Slave Pulley - POM

Spur Gear Drives are compatible with Straight-cut or Helical Gears.
CNC’d from hardened steel, the 58-tooth Helical Slave Pulley pairs with the 10-tooth Helical Motor Pulley, giving a gear ratio of 1:5.8. Compared to the 59-tooth Straight-cut Slave Pulley’s ratio of 1:5.9, Helical gears will ultimately have a higher top speed.

Helical Gears provide more surface contact between the teeth, resulting in a smoother & quieter ride.

Straight-cut Gears are the cheaper option – still providing amazing torque & performance, while running a bit louder than helical.

Connects to Hub Adaptor using 5x m5 x 12mm Torx head screws.

Spur POM Gear Drive 10 Tooth 10º HELICAL Cut Motor Pulley -c45 HARDENED Steel

10-Tooth helical-cut Motor Pulley for Spur Gear Drive

Helical Gears provide more surface contact between the teeth, resulting in a smoother & quieter ride.

Spur Gear Drive HELICAL or STRAIGHT Cut Slave Pulleys Made from POM or Steel

Spur Gear Drives are compatible with Straight-cut or Helical Gears.
Made from premium POM plastic, the 58-tooth Helical Slave Pulley pairs with the 10-tooth Helical Motor Pulley, giving a gear ratio of 1:5.8. Compared to the 59-tooth Straight-cut Slave Pulley’s ratio of 1:5.9, Helical gears will ultimately have a higher top speed.

Helical Gears provide more surface contact between the teeth, resulting in a smoother & quieter ride.

Straight-cut Gears are the cheaper option – still providing amazing torque & performance, while running a bit louder than helical.

Connects to Hub Adaptor using 5x m5 x 12mm Torx head screws.

Spur Gear Drive CUSTOM Motor Pulley - c45 HARDENED STEEL

SPUR GEAR DRIVE Motor Mounts can run using Helical or Straight-cut pulleys.

Helical Motor Pulleys give a gear ratio of 1:5.8 when paired with the 58 tooth Helical Slave Pulley. The Helical shape allows for more surface contact between the Slave & Motor Pulley Teeth, creating a quiet & efficient drive.

Straight-cut Motor pulleys pair with a 59 tooth Slave Pulley, giving a ratio of 1:5.9 – meaning there will be a tad more power when accelerating in comparison to the Helicals. However, due to less surface-contact between the gears, Straight-cuts are much louder when riding along (although we’ve found some mad people who like/prefer the noise!).

Made using Hardened Steel.

Mountainboard Motor Mount V-Ring TUB Seals - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

Mountainboard Motor Mount Truck Connector

Works with PRO BELT & SPUR GEAR Drives.
The Clamp housing slips over the axels of Precision CNC’d Vertigo Trucks, ensuring the drivetrain sits at the correct angle.
Working in conjunction with the Conical Clamp, when connected together the housing squeezes the clamp to the hanger, securely attaching the drivetrain to the trucks.

Precision CNC’d from T6 Heat-treated Aluminium.

Mountainboard Motor Mount Connector Conical Clamp

Works with PRO BELT & SPUR GEAR Drives.

Designed to work in conjunction & attach securely to Precision CNC’d VERTIGO trucks, the Conical Clamp slips tightly over the CNC’d square on the hanger of the trucks. When attached to the Clamp Housing, the Conical Clamp tightens around the hanger, ensuring secure & accurate Motor Mount attachment.

Precision CNC’d from T6 Heat-treated Aluminium.

Mountainboard Motor Mount Rubber pad for Conical Clamps - Fits both BELT & SPUR Gear Drive Motor Mounts

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

M3 x 4mm Dome Headed Head Allen-Key Bolt DIN6912 Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!