Home»Trucks»ATB Spring Trucks with Brakes»INFINITY MAGURA»INFINITY - MAGURA SUPERSTAR & SOLID Disks - Smart Group Special

The TRAMPA's MAGURA HS-11 BRAKE system is an incredibly powerful braking system that is certain to slow you down or even stop you dead if you squeeze to hard! By mounting MAGURA's Hydraulic Brake calipers (mounted in reverse fashion to that of a bicycle) onto a TRAMPA Brake Hanger & by squeezing the hand help brake lever as you ride, the hydraulic fluid (MAGURA Blood) runs evenly through the system applying pressure through the BRAKE PADS onto the special made 5mm thick Aluminum BRAKE DISKS. The Brake Disks can be mounted to any of the 5 Spoke wheels that TRAMPA offers. This incredibly powerful brake system prevents the need to get down & power slide, your always in contgrol of your speed and when going to quick for comfort will trim your speed suitably to make it around a tight corner without stopping or stop you dead should you so require. This incredibly powerful braking system will allow you to ride in places you have only ever imagined before!

MAGURA are a famous German company who specialise in hydraulic braking systems for bicycles. The HS-11 Hydraulic Brakes are MAGURA's original Hydraulic braking system. MAGURA have over 30 years of testing with this equipment. The HS-11 setup is also well proven to be perfect for our Mountainboarding application - specially when modified to fit to the immense TRAMPA Brake Trucks & SUPERSTAR RIMS. Using some clever mounting holes that we make into the Brake Hanger to hold the Brake Caliper completely steady, a change of cable length is used between the 2 Calipers and by mounting the brake calipers in reverse (pushing out rather than pushing in) the MAGURA Brake system neatly fixes onto the TRAMPA Brake hanger, positioning the caliper in the perfect for the best braking application against the Superstar Wheel...

The TRAMPA INFINITY truck (So called because infinity is for ever) is the strongest SPRING TRUCK in the TRAMPA product range! To ensure the maximum strength possible the Hanger body is made from FORGED ALUMINUM. It is one solid piece! The INFINITY Hanger is fitted with 12mm SOLID STEEL Axles. The Solid Axles are HEAT TREATED. Heat treating steel makes it substantially stronger, more resistant to impact & less prone to rust. 12mm Solid Axles are without doubt the strongest Axles in the TRAMPA range. The Axles are first Glued & then Screwed with a Marine Grade Stainless Steel Grub Screw locking them in the perfect position to mount your wheel too. The Hanger is connected to an EXTRUDED & T6 HEAT TREATED Aluminum BASEPLATE & as it's name suggests the INFINITY HS-11 TRUCK is designed to last forever!!

Once the Hanger has had its Axles fitted it is sent away to the CNC factory to have the Kingpin holes & the MAGURA Brake / E-Drive mounting points precision milled. CNC milling guarantees precision work. It is imperative that all of these important holes are accurately positioned in order to ensure the best performance to the rider, as well as making the Truck easy to assemble & service. The workers modify the back of the hanger by milling a flat surface so that we can mount the Brakes or E-Drive equipment flush against. We then drill an extra hole & insert it with a thread so to be able to screw in a bolt & fix something into it. A small semi-circle "Cradle" is milled at the top of the Hanger,  acting as an anchor, it eliminates movement normally associated to a single fixing point. We are able to fix the MAGURA Braking system or the NEW TRAMPA E-DRIVE system into this thread & cradle, making a very strong fix between the two. The HS11 Magura Braking System & the E-Drive system are both very powerful and they need a very strong mounting point for max performance.!

In order to give the "Two Tone Pimp Finish" the INFINITY Hanger is EDP painted MATT BLACK for metal protection & colour coordinating good looks before the CNC work is carried out. The INFINITY Brake Board / E-Drive Hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the board has a "center wheel width" of 15 Inches.

Once back from the CNC factory the MAGURA HS11 Hydraulic Brake calipers are filled with MAGURA Brake fluid (MAGURA Brake Blood) before being then fitted to this Hanger! The Brakes come to you as a pre-assembled set, including BRAKE DISKS, SPACERS & specially made M4x52.5mm Countersunk BOLTS ready to fit the Brake Disks directly to your SUPERSTAR Wheels. The MAGURA Brake system is very powerful. It can be fitted to the front or the back of the board to suit your riding preference & will stop you faster than you have ever imagined before! It has transformed the riding experience for many riders, opening up what was previously un-ridable terrain into easily conquerable terrain.

The HS11 Hydraulic Brake System is designed to fit the 35° HS11 Brake Deck or the 35° HolyPro Deck without any modification needed at all. The HS11 Truck will also fit to any 35° TRAMPA Deck, but as the calipers take up a lot of space on the hanger, some modifications may be needed to be made to the deck, in order to create the space to house them to allow the deck to steer correctly.

Magura Bolt used to mount the calipers to the hanger - Part A M6 x 12mm

As expected from TRAMPA all Hardware parts are made from the finest A2 Marine Grade Stainless steel available to us & ensure a rust free connection for maximum durability!.

Magura Brake special mounting bolt - used to fix the calipers to the hanger..
Loosely place the calliper over bolt C & position part D into the half moon housing in the hanger.. Place part B (bolt mounting spacer) over bolts C & D and use part A to screw them both tightly into the hanger.. Using a 5mm Allen Key tighten the bolts into parts C+D into the hanger - you do not want any play in this part so make sure this is tight - FT!!

Magura Brake Calipers & Cables

Magura Hydraulic Brake kit. Including Handle, Cables, Connections, Mounting bracket & comes fully bled ready to be mounted.. This kit will only fit to a Trampa spring style hanger that has been modified to fit the brake system.. This kit will not fit to a regular Trampa Spring hanger.. You also need top purchase the mounting bolts and assembly spacers

Magura Bolt mounting Spacer MG Stainless Steel - Part B

Magura mounting Bolt Spacer Marine Grade Stainless Steel - Part B. Secure your brake assembly through this special steel bracket.. As expected from Trampa this part is made from marine Grade Stainless Steel.. This special part gives the exact space required to fix parts C & D into the Hanger, FT!. Use part A to screw through part B into the fixing C & D into the Hanger. Ensure all the brake parts fixing to the hanger are very tight! FT!!

Magura Bolt used to mount the calipers to the hanger - PartC

Magura Brake special mounting bolt, used to fix Calliper to Hanger. Part C is made from Marine Grade stainless steel and will not rust on you!. This part C screws into the modified hangers and Locks the calipers in position.. As a trick to fix this to the hanger, use an M6 bolt and 2 x M6 nuts to lock into the special part C and then tighten into the Hanger.. Using a 10mm spanner tighten this part into the hanger so its really tight - FT. The brake caliper sits over Part C and with use of parts B, D & A locks the caliper into position ready for use.

Magura Bolt used to mount the calipers to the hanger - part D

Magura Brake special mounting bolt - used to help fix the Calliper into hanger. Part D is made from Marine Grade Stainless steel and will never rust on you.. Once part C is anchored into the hanger, slip the calliper over part C and push this part D into position.. Part D will sit in the half moon that has been CNC'd into the hanger.. Once part D is in position, place the bolt spacer (part B) over the parts C & D and insert the screw (part A) into C & D. You may need to rest your finger at the back of part D in order to get a purchase when screwing in part A but as soon as this has some resistance it will tighten nicely. Ensure the connection between the callipers and the hangers is very tight! FT

Magura 90º Bango cable connector - part F

This special part allows us to make the modification from Bike brakes to Mountainboard Brakes.. The length of the cable required to fit the distance between your callipers is 265mm. Use a cable steady and clamp or vise to hold the brake cable tight, then tap in this Part F into the cable with hammer.. Be careful not to split the cable when tapping in. Do not over heat the cable as this makes it flexi when tapping in...

Magura Valve bolt - part G

Use this part G to fix through part F (the 90º pipe connector) and connect into the brake caliper.. This special screw is hollow with a hole and allows the blood to flow through the system.. Ensure you have copper washers (part H) either side of the Part F to ensure a water tight fit.. Make sure this part is screwed into the caliper tight, but do not over tighten as it is fragile & will snap!.. We are checking the Magura website for details of its exact tightness in newton meters...

INFINITY Brake Hanger - 12mm SOLID Axles modifed to fit MAGURA Hydraulic brakes

TRAMPA's INFINITY HS11 MAGURA BRAKES HANGER is taken from the strongest SPRING TRUCK Hanger in the TRAMPA product range! To ensure the maximum strength possible the hanger body is made from FORGED ALUMINUM & is one solid piece! The INFINITY Hanger is fitted with 12mm SOLID STEEL Axles. The Solid Axles are HEAT TREATED. Heat treating steel makes it substantially stronger, more resistant to impact & less prone to rust. 12mm Solid Axles are without doubt the strongest Axles in the TRAMPA range. The Axles are first Glued & then Screwed with a Marine Grade Stainless Steel Grub Screw into the perfect position to mount your wheel.

Once the Hanger has had its Axles fitted it is sent away to the CNC factory to have the Kingpin holes & the Brake / E-Drive mounting points precision milled. CNC milling guarantees precision work. It is imperative that all of these important holes are accurately positioned in order to ensure the perfect assembly & best performance to the rider, as well as making the Truck easy to assembly & service. The workers modify the back of the hanger by milling a flat surface so that we can mount the Brakes or E-Drive equipment flush against. We then drill an extra hole & insert it with a thread to be able to screw a bolt to fix something into & a small semi-circle "Cradle" is milled at the top of the Hanger,  acting as an anchor, it eliminats movement normally associated to a single fixing point. We are able to fix the MAGURA Braking system or the NEW TRAMPA E-DRIVE system into this thread & cradle, making a very strong fix between the two. The HS11 Magura Braking System and the E-Drive Sytem are both very powerful, they need a very strong mounting point for max performance.!

In order to give the "Two Tone Pimp Finish" the INFINITY Hanger is EDP painted MATT BLACK for metal protection & colour coordinating good looks before the CNC work is carried out. The INFINITY Brake Board / E-Drive Hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the board has a "center wheel width" of 14 Inches.

Genuine SUPERSTAR CENTER-SET Rim 3.75x 2 Inch fits all 3.75 Inch Tyres - Matt BLACK

TRAMPA's SUPERSTAR Hub is a technically designed super-strength masterpiece of circular lushness & has been created for those who insist on fitting only the very best equipment! SUPERSTAR Hubs are available in loads of different Rim & Spoke colour combinations, its almost impossible to decide the combination you like the most!

The SUPERSTAR hub handles the highest inflation pressures on the market, which in turn increases roll speeds giving the rider the advantage over the competition, making them perfect for the best riders, i mean the insane! SUPERSTAR Rims are produced using original 'DuPont' materials (the best), whilst the STAR SPOKES are made using a custom made mould to give us an Extruded Aluminum profile that gets T6 Heat treated (Super Strength Aero-grade quality) & then sliced to requirement.

The SUPERSTAR Hub/wheel is fully constructed using A4 (Marine Grade) Stainless Steel Nuts & Bolts. Total & absolute product perfection!

SUPERSTAR Hubs are compatible with any tyre that TRAMPA offers up to 8 inches in size!

Disk Brakes for steep free-ride riding & Drive Gears for Electric boards or Electric motors can also be fitted to these amazing SUPERSTAR wheels... 

Bearings can be purchased at a discounted price when purchased with complete Hubs or wheels.