Home»Accessories»Spring Truck»ATB Hangers with Spacers & Nuts»VERTIGO Hanger BRAKES - 12mm Hollow steel

The VERTIGO BRAKE / E-DRIVE HANGER is a slimmed down light weight version of the Infinity Brake / E-Drive Hanger. To ensure the maximum strength possible the Hanger body is made from FORGED ALUMINUM & comes to us as one solid piece!

The VERTIGO BRAKE / E-DRIVE HANGER is CNC miilled to cut out the bulk of the weight whilst retaining the majority of its strength & allowing the Magura brakes or the new TRAMPA E-DRIVE gearing system to be mounted. The VERTIGO Hanger is fitted with 12mm HOLLOW STEEL Axles. The Axles are HEAT TREATED. Heat treating steel makes it substantially stronger & more resistant to impact. Hollow Steel Axles are substantially lighter than than Solid steel Axles.

CNC milling guarantees precision work. Ensuring the Kingpin Holes are accurately placed guarantee's the best performance to the rider as well as making the truck easy to assembly & service.  Whilst the Hanger is at the CNC factory, the workers modify the back of the hanger by milling a flat surface (so we can mount the equipment flush against the hanger) and then drilling an extra hole & inserting a thread for fixing. A small cradle is drilled at the top of the hanger to elliminate movement. We are able to fix the MAGURA Braking system or the NEW TRAMPA E-DRIVE sytem into this thread & cradle, making a very strong fix between the two. Your braking system very very powerful indeed, it needs a strong mounting point.. In order to give the "Two Tone Pimp Finish" the Infinity Hanger is EDP painted MATT BLACK for metal protection & colour coordinating good looks before the CNC work is carried out.

The VERTIGO Brake Board Hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the board has a "center wheel width" of 14 Inches.

7/16ths Nut - Marine Grade Stainless steel Nylock Axle HALF nut (W7/16-20T UNF) - Fits to 12mm Axles

This very special 7/16_^ths of an inch Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut.. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore further reducing weight in the Truck! A few Grams here & a few grams there soon adds up & makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area, where a few grams makes all the difference...

This very special 3/8_^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W7/16 - 20T - UNF. This Nut is used to hold the wheels onto the axles of the Spring Trucks fitted with 12mm axles. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 16mm or 5/8th_^ths of an Inch spanner to tighten / loosen the Nut onto the Axle or Kingpin. Do not overtighten the nut & make sure the wheel can spin freely but does not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

Axle support Spacer for Hangers with Brakes - 12 x 16 x 18.5mm - LATHED

This special 18.5mm Spacer is used to fit TRAMPA SUPERSTAR Wheels onto 12mm Axles with Brakes.  It was our intention to make all of our Spacers to be the same size (18.2mm) so they have multi applicational use. Sadly this isnt quite the case and the SUPERSTAR hubs need a slightly longer Spacer to fit the SUPERSTAR wheels onto the Brake Truck Hangers.

This 18.5mm spacer will only fit SUPERSTAR Wheels when fitting them onto the 12mm Spring Truck Axles that have been modifed to fit hydraulich Brakes. The SPacer positions the Hub Perfectly for the brakes to work.

The Spacer is produced as a long tube, its polished for surface protection & best appearance & then precision CNC cut to the exact length for accurate mounting. This Spacer will fit onto 12mm Axles only.

VERTIGO Brake Hanger - HOLLOW Axles modifed to fit MAGURA Hydraulic brakes

The VERTIGO BRAKE / E-DRIVE HANGER is a slimmed down light weight version of the Infinity Brake / E-Drive Hanger. To ensure the maximum strength possible the Hanger body is made from FORGED ALUMINUM & comes to us as one solid piece!

The VERTIGO BRAKE / E-DRIVE HANGER is CNC miilled to cut out the bulk of the weight whilst retaining the majority of its strength & allowing the Magura brakes or the new TRAMPA E-DRIVE gearing system to be mounted. The VERTIGO Hanger is fitted with 12mm HOLLOW STEEL Axles. The Axles are HEAT TREATED. Heat treating steel makes it substantially stronger & more resistant to impact. Hollow Steel Axles are substantially lighter than than Solid steel Axles.

CNC milling guarantees precision work. Ensuring the Kingpin Holes are accurately placed guarantee's the best performance to the rider as well as making the truck easy to assembly & service.  Whilst the Hanger is at the CNC factory, the workers modify the back of the hanger by milling a flat surface (so we can mount the equipment flush against the hanger) and then drilling an extra hole & inserting a thread for fixing. A small cradle is drilled at the top of the hanger to elliminate movement. We are able to fix the MAGURA Braking system or the NEW TRAMPA E-DRIVE sytem into this thread & cradle, making a very strong fix between the two. Your braking system is very powerful, it needs a good strong mounting point for max performance.. In order to give the "Two Tone Pimp Finish" the VERTIGO Brake / E-Drive Hanger is Anodised  GLOSS BLACK for metal protection & colour coordinating good looks before the CNC work is done.

The VERTIGO Brake Board / E-Drive Hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the board has a "center wheel width" of 15 Inches.