Home»Accessories»Spring Truck»ATB Hangers with Spacers & Nuts»ULTIMATE Hanger ATB - TITANIUM WHITE

The ULTIMATE TITANIUM HANGER is a slimmed down SUPER light weight version of the original INFINTY Hanger. The Hanger body is produced from CAST ALUMINUM and is one solid piece. Without stripping any of its critical strength a CNC milling machine accurately cuts out the bulk of the material which results in the ULTIMATE hanger being almost as strong as the Infinity BUT nearly 30% lighter in over all weight. :-)

The ULTIMATE Hanger is then drilled & fitted with SOLID 9.525mm TITANIUM Axles. The TITANIUM Axles reduce the overal weight of the ULTIMATE hanger even further. Marine Grade Stainless steel GRUB SCREWS help keep the TITANIUM Axles locked into the correct place within the Hanger.

The CNC milling guarantees to drill accurately. Ensuring the Kingpin Holes are accurately placed guarantees' the best performance to the rider as well as making the truck easy to assembly & service. In order to give the "Two Tone Pimp Finish" the Ultimate Hanger is POWDER COATED Gloss White for metal protection & colour coordinating good looks before the CNC work is carried out.

The Ultimate hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the board has a center wheel width of 14 Inches.

TRAMPA's ULTIMATE Hanger uses 2x 18.2mm x 9.525mm SPACERS (1 either side). The spacer slips onto the axles, leaving the perfect space to mount the TRAMPA wheels accurately. Use the 3/8/ths of an inch Axle Nuts to lock the wheels into place on the axle.

Kingpin bushings push into the Kingpin holes, in both the Hanger & the Baseplate. When all the bushings are in position, push the Baseplate over the Hanger and into position so that all the Kingpin holes line up. When this is the case you will be able to push the kingpin, from the front to the truck to the back, through the holes in the assembly & connecting them all together. Remember to add the washer onto the kingpin before sliding into the assembly. As these bushings are made from plastic and sit in between moving metal parts, these small parts (bushings) will need checking & possibly need replacing over time. So its good practice to check & replace them when you swap your hanger or make service work to your trucks...

3/8ths Nut - Marine Grade Stainless steel Nylock HALF nut W3/8 - 24T UNF

This very special Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore reducing weight in the Truck also! A few Grams here & a few grams there soon adds up to quite alot & that makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area...

This very special 3/8^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W3/8_^ths - 24T - UNF. This Nut is used to hold the wheels onto the axles of the 9.525mm (3/8ths of Inch or otherwise referred to as 10mm) SKATE TRUCKS & also the Spring Trucks fitted with TITANIUM axles. This Nut is also used to hold the KINGPIN in position on all Skate Trucks. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 14mm or 9/16^ths of an Inch spanner to tighten the Nut onto the Axle or Kingpin, do not overtighten the nut, allow the wheel to spin freely but not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

 - Fits to 9.525mm (3/8ths) Axles & Skate Truck Kingpins

Wheel support spacer for all TRAMPA Wheels on 9.525 ATB Axles - CNC precision 9.525mm x 13.525mm x 18.2mm

This special 9.525mm (id) x 13.52mm (od) x 18..2mm (long) Aluminium Spacer has two purposes - It is firstly known as a Bearing Support Spacer as this spacer fits between the Bearings of the HYPA hub when mounting the HYPA wheel onto 9.525mm (10mm) or 3/8ths of an inch Axles, & secondly this spacer is also known as the "WHEEL SUPPORT SPACER" as it is also used to position all the TRAMPA wheels into the correct position when mounting onto Spring Trucks with 9.525mm TITANIUM Axles.

TRAMPA's spacers are produced as one long tube. The Tube is Heat Treated gaining maximum strength, then CNC cut to the exact length for precision & problem free wheel mounting.....!

ULTIMATE ATB Hanger - 9.525mm TITANIUM Axles, Powder Coated White & CNC'd light

The ULTIMATE ATB TITANIUM HANGER is a slimmed down SUPER light weight version of the original INFINTY Hanger. The Hanger is made from FORGED ALUMINUM & is one solid piece. Without stripping any of its critical strength a CNC milling machine accurately cuts out the bulk of the material resulting in the ULTIMATE hanger being almost as strong as the Infinity BUT nearly 30% lighter in overall weight.

The ULTIMATE Hanger is equipped with 9.525mm (10mm) SOLID TITANIUM Axles. TITANIUM Axles reduce the overall weight of the ULTIMATE hanger even more than the 12mm Hollow axles do in the Vertigo Hanger.

CNC milling guarantees precision work. Ensuring the Kingpin Holes are accurately placed guarantee's the best performance to the rider as well as making the truck easy to assembly & service. In order to give the "Two Tone Pimp Finish" the Ultimate Hanger is POWDER COATED Gloss White for metal protection & colour coordinating good looks before the CNC work is carried out.

The ULTIMATE hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the board has a center wheel width of 14 Inches.