This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

TWIN 14FiFties Motor mount & 44 Tooth Pulley Kit with MOTOR & 2x 14FiFties Trucks & 4x Gummies Wheels

14FiFties Motor Mount with Motor Adaptor & 15mm Belt Tensioner - TWIN 14FiFties Pulley kit with 44 Tooth Slave & 350mm x 15mm Belt to fit 5 Inch GUMMIES Tyres on 14FiFties Trucks 1x Custom TRAMPA DC Motor with BASIC Filters included 1x Custom TRAMPA DC Motor with BASIC Filters included HALF CAGE Motor protection  with anodised with Filter - TWIN 14FiFties - 14.5 Inches wide & Mounted at 50º CNC Precision made Super Extra Wide All Terrain Longboard Truck with 12mm Axles to fit any TRAMPA Wheel!! Custom TRAMPA hub with Gummies 125mm Longboard Wheel Tyre
RRP
£825+

350mm long x 15mm wide High Torque Drive 55mm High Power STRONGBELT for Gummie wheels on the CARVE or ORRSOM Boards

This is a 350mm long x 15mm wide High Torque Drive (HTD) Re-enforced Rubber Belt, which has 5mm Tooth Spacing (5M). It is a High Power rated (HP) TRANSMISSON BELT made by the world famous German Brand called STRONGBELT. This one is used to transfer the power from the Motor & Motor Pulley into power at the rear wheels of a TRAMPA Electric Street Carver

TRAMPA opted to set a new standard in E-Skating, becoming the first in the world to fit to all of the E-Boards in its range, a 15mm wide TRANSMISSON BELT as standard! Our standard 15mm belt is almost double the width of nearly all other E-Sk8's out there, they tend to use a flimsy off the shelf 8/9mm transmission belts which can be prone to stretch, slip & ultimately snap. 

Using a re-enforced 15mm wide High Power Belt reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. When accelerating or engine breaking (KERS), even from a standing start the STRONGBELT power is smooth & does not slip, or strain the motor, it does a damn gooood job!.....

STRONGBELT, as their name suggests, is a heavy industry brand that usually supplies the likes of Train manufacturers, where serious levels of quality with no excuses on failure are expected from the product as standard, as failure for such an item is serious as the consequences may result in death! STRONGBELT weave KEVLAR into their Pulley Belts, Kevlar is one of the strongest fibers known to man, its often added into materials to gain extra strength.... STRONGBELT have the best reputation in the Power Transmission Industry. These extra quality details in the production of our electronic motor drives, provides the maximum responsiveness achievable whilst maintaining a super smooth power delivery to the rider at all times. 

TRAMPA Custom DC Motor 6364 6376 6386 - SINGLE

TRAMPA Custom Single motor 6364 160Kv or 6376 wound in 160Kv or 185Kv configurations.

TRAMPA's very own purpose made 160 KV 6376 Out-Runner Motor provides 160RPM per volt. CUSTOM MADE to handle HIGH Power outputs.

This Motor has many NEW features that increase both hardiness & efficiency!

- Improved thermal design; with a more thermally-connected-mass, heat can dissipate much more efficiently. The new Rotor bodies feature raised rings that increase surface area, further helping heat dissipation.

- Stronger Hardware; larger & stronger bolts have been used throughout the motor, improving the motor’s strength & sturdiness, while making maintenance a lot less fiddle-y.

- Optimised Air-cooling; Stator cooling via air-flow - larger openings on the stator & having no sensor PCB both help to encourage a cooling flow of air through the motor. Further improve the air-flow using the MKII Motor Housing & Fan End-cap Kit.    

- Accurate & faster temperature readings; With a heat sensor glued to the copper windings in the ideal location, it's possible to get faster and more accurate motor-temp readings, which is important for future sensorless startup algorithms.

- Optimised for sensorless rotor position detection; With no sensor PCB inside, this motor works best when used with a VESC Speed Controller featuring Advanced Sensorless Startup - when paired & activated the motor will be able to reach full torque at 0RMP! 


All TRAMPA Motors use Premium high-temperature Copper & the highest grade of Neodymium Magnets available. The magnets connect to an Extended & Heat treated 8mm Steel Axle shaft that's locked in a balanced position with 4 precision Bearings. All screws & fixings used in the assembly are Marine grade Stainless Steel. All creating super-tough  motors that can easily out-perform the competition!

Our special design allows you to fit mesh filters, or entire Motor housings, preventing the impregnation of particles entering in the motor & stopping them running smoothly. The motor Stators are equipped with twelve M4 threaded mounting holes, sitting on a 44mm diameter circle. The extra holes allow the motor to be mounted at the exact angle needed so the motor cables always sit in the perfect angle, towards the mount or deck.

Using 38.5mm x 8mm Heat-Treated Hardened-Steel Motor Shaft (fitted with a 12x3x3mm KEYWAY locator as standard), the extra length of the Axle allows us to add adequate support with Motor Axle Supports, & allows us to fit  Extra wide Motor Pulleys for the 15 - 20mm wide HTD 5M STRONGBELTs we use as standard, guaranteeing a much stronger power delivery.

Two 3x3x12mm KEYWAYs lock the Axle shaft at both ends (1 to the Rotor & 1 to the Motor Pulley), eliminating any & all "Motor slip", & providing maximum performance to the rider, while gaining critical data for the VESC speed controller.

The Heavy Duty & high quality power cables use 4mm Gold Plated Bullet Connectors to connect to a power source. 

 

Aluminium Star Shaped Motor Filter Holder for all 63mm size Motors

The Motor Star Holder is a critical piece of Trampa motors - it holds in place the filter at the end of the motor casing keeping dust and debris out so you can ride longer!

Stainless Steel Motor Filter is Held in place using the Motor filter holder

This Stainless Steel 'Motor END FILTER' fits into the end of any of TRAMPA's motors,

Fitting filters to your motors prevents dust n debris from entering the motor whilst still allowing cool air enter & pass though, encouraging cool operating temperatures.

This circular Stainless Steel Filter is pre-punched with the fixing holes to fit to all TRAMPA Motors. It requires the STAR SHAPED ALUMINUM END FILTER HOLDER to secure the end filter into place, whilst M3x4mm Dome Headed bolts screw through the star holder & filter turning directly into the end of the motor.

Stainless Steel Motor filter wraps around the CAN of the 63mm TRAMPA motors preventing dust n debris from entering the motor

This Stainless Steel WRAP Around Motor filter wraps around the CAN or BASE of any of TRAMPA's motors,

There are air cooling holes in the base of TRAMPA's motors to encourage cool air to enter to keep the motor running cool, prolongiung maximum throttle! The stainless filters prevent dust n debris from entering the motor whilst still allowing cool air enter & pass though.

The WRAP Around Stainless Filter has fixing holes pre-punched into it. During installation the filter should be folded in half. This is best done over a firm accurate straight line such as a metal ruler. Once the filter is folded in half it is double thickness & therefore double filtered...

Using tiny M3x4mm Dome Headed Allen Key bolts & a tiny amount of non permenant Lock Tight to stop them running out, pass the little bolts though the pre-punched fixing holes in the filter & stretching the filter into a tight position & screw directly into the can of the motor.

This filter fits all TRAMPA Motors & is best used in conjunction with the Motor END FILTER & ALUMINUM END FILTER HOLDER that secures the end filter in place

HALF CAGE Motor protection Housing - Aluminium

TRAMPA's HALF CAGE Motor Protection Sleeve is CNC precision cut from premium T6 grade Ali. Its Heat Treated & anodised in all the usual 10 colours for customisation & finally installed with a contrasting Black Painted Stainless Steel Anti Particle filter.

HALF CAGE Motor Protectors connect to nearly all Motor Mount options that TRAMPA offers & will fit to all of TRAMPA's 63mm Motors. They work in conjunction with the motor END FILTER & Star shaped FILTER HOLDER or if you have space on your hanger to fit the MOTOR FANS for additional cooling.

The Stainless Steel Mesh Gauge is 0.15mm, so being this tiny means only allow particulates that are small enough to pass through the air gap between motor magnets & the stator will get in, preventing excess damage & maintaining long life for your motors. 

This Motor protection cage has been designed for those who want to save as much weight as possible whilst still maintaining a high level of protection against the ingress of grit or dirt & for sharp good looks. 

Fitting Motor any of the Motor Filters TRAMPA offers, is a good thing for your motor allowing constant cooling whilst reducing wear at all times. 

Aluminium Star Shaped Motor Filter Holder for all 63mm size Motors

The Motor Star Holder is a critical piece of Trampa motors - it holds in place the filter at the end of the motor casing keeping dust and debris out so you can ride longer!

Stainless Steel Motor Filter is Held in place using the Motor filter holder

This Stainless Steel 'Motor END FILTER' fits into the end of any of TRAMPA's motors,

Fitting filters to your motors prevents dust n debris from entering the motor whilst still allowing cool air enter & pass though, encouraging cool operating temperatures.

This circular Stainless Steel Filter is pre-punched with the fixing holes to fit to all TRAMPA Motors. It requires the STAR SHAPED ALUMINUM END FILTER HOLDER to secure the end filter into place, whilst M3x4mm Dome Headed bolts screw through the star holder & filter turning directly into the end of the motor.

44 Tooth Slave Pulley - HYPA or SUPERSTAR/MEGASTAR - URBAN Motor Mounts

TRAMPA's 44 Tooth Slave Pulley has been designed to be used specifically when connecting electric motors through the URBAN Motor Mounts when using the new & oversized, super grippy GUMMIES longboard style tyres.  Frank was un-able to design 1 pulley to fit all styles of TRAMPA hub, so there are two different models for HYPA or SUPERSTAR/MEGASTAR Hubs.

The 44 Tooth Slave Pulley has been precision milled from super-light-weight & mega strong Heat Treated T6 Aluminum. The pulleys teeth stand 5mm tall, this is the same size teeth as that found on TRAMPA's Premium 15mm wide German made 'Strongbelt' & when the Strongbelts are wrapped around the pulleys, the belt fits so efficiently it has what we call HIGH TORQUE DRIVE (HTD). HTD insures all of the motors Torque is pushed through the pulleys into the wheels & when coupled with the amazing VESC 6 & 12s Battery power provides instant smooth unreal Power on tap to the rider!

This smaller sized 44 Tooth pulley is actually higher in gearing than the 66 tooth & therefore when fitted it increases the final drive (top Speed) compensating for the smaller sized final drive the wheel was originally intended to fit to... Gummies tyres only measure 125mm which are obviously smaller than 6.5, 7 & 8 inch wheel options we also offer so the Gummies Tyres love the extra gearing the 44 Tooth Brings :-)

TRAMPA's 44 Tooth Slave Pulley for HYPA hubs works in conjunction with all & any of the 13, 14 or 15 tooth Motor Pulley in the range. Changing your Motor Pulley will drastically alter the performance & characteristics of your ride... 13 Tooth motor Pulley is best for Hill Climbing whilst 15 Tooth Motor Pulley is best for high speed, 14 tooth motor Pulley will give you good all round performance...

To connect the 44 Tooth Pulley to the hubs you will need 5 or 6x M4x40mm Socket capped Bolts which screw through the wheel assembly directly into the Pulley very neatly!

Custom 15mm wide Motor Pulley 13, 14 or 15 tooth

TRAMPA's 15mm wide 13-15 Tooth Motor Pulleys connect directly to the Motor Axle & are secured into position using a Magnetic Fixing Key & 4mm Locking Grub Screw.

These custom made Motor Pulley Wheels  fit 15mm wide STRONGBELTS, which should never stretch or break whilst at the same time providing a very smooth power delivery to the user - even from a standing start.

Choice of Aluminium or Black Steel. Aluminium Pulleys are perfect for those looking to save every gram possible on their board - Black Steel Pullys are heavier, but much harder wearing.

Changing your Motor Pulley &/or Drive pulley wheels will drastically change the performance of your ride... :-)

13 Tooth
Best performance for climbing steep inclines.

14 Tooth 
Best all-round performance

15 Tooth 
Best performance forreaching top speeds.

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x8mm

TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.

TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....

M3 x 4mm Dome Headed Head Allen-Key Bolt DIN6912 Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

This Bolt is DOME HEADED, meaning that when screwed into position it sits low & neatly over the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-TRAMPA MOTORS

M3 x 4mm Dome Headed Head Allen-Key Bolt DIN6912 Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

This Bolt is DOME HEADED, meaning that when screwed into position it sits low & neatly over the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-TRAMPA MOTORS

M4 x 40mm Socket Capped Allen-Key Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA SUPERSTAR HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim of the SUPERSTAR HUB eventually screwing  into the M4 nut on the other side easly.

Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

USED FOR CONNECTING:  

SUPERSTAR HUBS       
MEGASTAR HUBS       
PHATLADS HUBS

M4 x 35mm Socket Capped Allen-Key Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 35mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the TRAMPA HYPA HUBS. The socket capped head of the Bolt fits neatly into the Bolt housing of the HYPA HUB marrying into the M4 nut located in the housing on the other side of the hub.

Weighing just 3 grams each these bolts are very lightweight. They look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You will need a 3mm Allen Key to tighten & loosen the Nuts & Bolts from the hub. Ensure all your Nuts & Bolts are tight before riding!

M4 x 4mm Grub Screw M4 x 4mm Motor Pulley Grub Screw - Connects the Motor Pulley onto the Motor Axle Shaft

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts

Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or  8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!

3/8ths Nut - Marine Grade Stainless steel Nylock HALF nut W3/8 - 24T UNF

This very special Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore reducing weight in the Truck also! A few Grams here & a few grams there soon adds up to quite alot & that makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area...

This very special 3/8ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W3/8ths - 24T - UNF. This Nut is used to hold the wheels onto the axles of the 9.525mm (3/8ths of Inch or otherwise referred to as 10mm) SKATE TRUCKS & also the Spring Trucks fitted with TITANIUM axles. This Nut is also used to hold the KINGPIN in position on all Skate Trucks. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 14mm or 9/16ths of an Inch spanner to tighten the Nut onto the Axle or Kingpin, do not overtighten the nut, allow the wheel to spin freely but not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

 - Fits to 9.525mm (3/8ths) Axles & Skate Truck Kingpins

7/16ths Nut - Marine Grade Stainless steel Nylock Axle HALF nut (W7/16-20T UNF) - Fits to 12mm Axles

This very special 7/16ths of an inch Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut.. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore further reducing weight in the Truck! A few Grams here & a few grams there soon adds up & makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area, where a few grams makes all the difference...

This very special 3/8ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W7/16 - 20T - UNF. This Nut is used to hold the wheels onto the axles of the Spring Trucks fitted with 12mm axles. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 16mm or 5/8thths of an Inch spanner to tighten / loosen the Nut onto the Axle or Kingpin. Do not overtighten the nut & make sure the wheel can spin freely but does not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

Wheel support spacer for all TRAMPA Wheels on 12mm ATB Axles - CNC precision 12mm x 16mm x 18.2mm - CUSTOM

This special Spacer measures 12mm (id) x 16mm (od) x 18.2mm (long) & has 2 uses!. It is firstly known as the Bearing Support Spacer as this Spacer fits between the Bearings of a 6 Spoked HYPA Hub, (when mounting the HYPA wheel onto 12mm Axles) & secondly it is also known as the AXLE SUPPORT SPACER as this spacer is also used to position any of the TRAMPA wheels in the perfect position onto the axles of 12mm TRAMPA Spring trucks....

TRAMPA spacers are produced as one long tube. The Tube is Heat Treated to gain extra strength & is then Bead Polished to give the metal extra surface protection & a shiny best appearance. The tube is then cut to the exact length for precision mounting. 

PRECISION Shim spacer - Bridges the tiny gaps between bearings on 12mm axles - 12 x 16 x 1mm

This little STAINLESS STEEL Shim Spacer is precision made. It ensures maximum performance to the wheels & nuts. Made from Marine grade stainless steel it will not rust on you! It is used to hold the bearings in the perfect position & also to bridge tiny gaps on the axles, ensuring an accurate fit with NO rattles!

The Shim spacer slips onto the Axle, fitting either side of the Bearings when the wheel is being fitted onto 12mm axles.

This tiny spacer positions the wheel perfectly on the axle, holding the Bearing in the best possible place to help achieve maximum spin rate for the bearing & wheel. Its little parts like these that suffer the most amount of abuse, especially when they are used in the harsh conditions that they are. Check from time to time they are in good order & possibly replacing them every now & then this good practice will ensure your board stays in tip-top condition, always!

14FiFties Extra Wide Longboard Hanger 355mm with 12mm HOLLOW Steel Axles

Introducing the 14-FiFties EXTRA EXTRA Wide Longboard HANGER, the newest edition to TRAMPA's range of amazing Long-Board Parts

Almost identical in design to TRAMPA's amazing 12-FiFties Trucks, TRAMPA has beefed up the 14FiFties & feeding them on steroids, having added some extra bulk to the body & fitted them with 12mm Axles to accept larger wheels....

The 14-FiFties Trucks have been specially made to celebrate TRAMPA's 20th Birthday (02.02.2022) & to fit TRAMPA's very latest ORRSOM GT Longboard Deck that's due out in early 2022....

So you know the terminology & how it is the 14-FiFties got its name, the 14FiFties Hanger with 12mm Axles mounted, measures 14 inches wide, whilst the mounting angle of the Kingpin is 50 Degree's, so the name 14FiFties was easy spawned...

Designed to be used in conjunction with our NEW ORRSOM GT longboard deck , the 14FiFties Trucks  use the same parts for assembly as or 12FiFties Hangers , BUT NOW with Customizable Baseplate colors & Endless Bushing options.

The extra 2 inches width provides superior stability, specially at high speed, as well as the extra clearance needed for adding larger wheels (Adding larger than 6 inch wheels to the 12FiFties Trucks would often result in toe bite on tight turns). The 14FiFties Trucks being fitted with 12mm Axles are compatible to house wheel sizes from 6.5'' (URBAN Treads - for speed street cruising), all the way through the range up to 9'' pneumatic tires - providing the most unrivaled off road Long- Board Style Board experience ever.

TRAMPA's 14FiFties Longboard Trucks  are the widest, strongest, longest, electric longboard trucks on the market today!

Designed to fit with our standard sized Skate Truck kingpin (9.4 x 50mm) & mounted at 50º angle to the base plate for optimal steering responsiveness. 

14FiFties  Base plates are available in 10 different anodized colors for unrivaled customization! 

Precision CNC'd from solid blocks of T6 heat-treated Aluminum, 14FiFties HANGERS are remarkably strong, able to withstand the forces, bumps or crashes they'll inevitably receive if ridden properly. As well as looking the part with an andonised black finish!

The hanger body has been CNC'd and then where crucial for motor mounting milled down to 19.5mm x 19.5mm. Since this is a 'one of a kind' longboard truck, it would have not been complete without its very own electric motor mounting system, based on the All-terrain Open Belt Drive system developed for the MTB spring trucks offers unrivaled performance (customized with a range of wheel and motor pulley options), straight forward installation and trouble-free maintenance. 

Custom Blood Orange Bushings - High Performance Urethane Bushings with lots of Flex options for customisation

The TRAMPA-IR truck and 12/14FIFTIES longboard trucks make use of Blood Orange's Barrel, Insert and Wedge bushings.

Using a high responsive nylon formula, the barrel bushings are designed to eliminate any gaps between bushing, hangar and kingpin. Less play on the pivot axis means improved responsiveness and a rapid return to center for those ultra tight turns!

The barrel design has been refined over many years through the development of skate truck design, and has proven to be strong and rugged.  The high rebound properties of the urethane also means it doesnt loose its uniform leaning properties, which is essential for downhill stability. 

Rubber hardness is measured in Shore Durometer resistance, These Skate Bushings are 89a rubber hardness, an ideal for greater stability at high speed, while reducing some turning capability. Used in conjunction with a flat plate washer, the bushing can be tightened onto the kingpin to increase steering resistance.


 

Custom Blood Orange PLUG BARREL Bushing - High Performance Urethane Bushings with lots of Flex options for customisation

The TRAMPA-IR Truck & 12/14FiFties longboard Trucks make use of Blood Orange's PLUG Barrel & WEDGE bushings.

Using a high responsive nylon formula, the insert bushings are designed to eliminate any gaps between bushing, hangar and kingpin. Less play on the pivot axis means improved responsiveness and a rapid return to center for those ultra tight turns!

The unique stepped plug design sits within the bushing recess on the IR hanger which helps the complete truck become more stable and restricts unwanted movement within the double kingpin design making it very comfortable at high speeds.

Rubber hardness is measured in Shore Durometer resistance, These Skate Bushings are 89a rubber hardness, which are and intermediate hardness giving good compromise between stability at speed and responsiveness when carving. Used in conjunction with a flat plate washer, the bushing can be tightened onto the kingpin to increase steering resistance.


 

HYPA Hub 3.75x 2 Inch - Any Colour you like!

TRAMPA's 6 spoke HYPA Hub is by far the lightest & weight for weight compared, the strongest 3.75-inch hub on the market today!

The HYPA hubs 6 spoke design is technically advanced & is manufactured using original Du-Pont materials & the very latest in precision injection molding machinery - No quality expense is spared! This deluxe combination of technical design, top quality machinery & original genuine materials, creates a product that is far superior to all of our competitions, resulting in performance that is well beyond normal expectations. This extra performance means the TRAMPA HYPA hub can handle much higher than recommended tyre inflation pressures, generating substantially higher than normal roll speeds. Back in the day during testing, our crash test dummies (i mean the Team riders) commonly rode with these hubs well above 80psi & beyond.... 

The HYPA hubs are held together using only the best Marine Grade (A4) Stainless steel Nuts & Bolts so they definitely wont rust on you (EVER) & are therefore perfect for bad conditions. All the Bolts used by TRAMPA have been dipped in a special Blue Locking Paste & all the Nuts are fitted with the world renowned Nylon "Nylock" Nut locking System, all these no expense spared small details ensure you get the absolute best hub possible!

HYPA hubs are available in loads of different colours & surface finishes, all of which are TRAMPA embossed between the spokes proving the top quality! Do not buy imitations as they will not perform the same!  TRAMPA’s own high class Steel Bearings, (Genuine  ABEC 5 rated Bearings) push perfectly into the HYPA hub bearing housing, guaranteeing the fastest spin rate to the wheel possible. Use either Bearing reducer sleeves into 12mm Bearings or use TRAMPA's 10mm Bearings to fit the HYPA hubs onto smaller sized skate axles. HYPA hubs are compatible with all known 8-inch tyres currently on the market including MBS & Scrub. Put quite simply – HYPA hubs are by the Best!

Along with many other applications that these wheels will fit too, the HYPA hub will fit and accept ALL the other brands of mountain boards on the market including MBS, SCRUB & KHEO, so when you are looking for an upgrade to your ride you know where too look! Basically the HYPA Hub will fit to anything that uses a Imperial 7/16ths (9.52mm) or 12mm bearings to fit onto the axle. If you already have your own 12mm bearings there are conversion spacers available to convert your 12mm bearings to work on the 7/16ths Imperial (9.52mm) skate axles and a different size spacer to convert them to fit 10mm (metric) scooter axles (see associated parts for details).

Bearings are supplied at a discounted price when purchased with hubs...

Rim Diameter 3.75 Inch
Rim Width      2 Inch or 50mm
​Fits all Tyres with 3.75 Inch rim inflating up to 8 inch in Diameter

 

GUMMIES 5 Inch Tyre - The Worlds largest Longboard wheel fixes to Any of the TRAMPA HYPA, SUPERSTAR & 8 Inch MEGASTAR Hubs

TRAMPA's AMAZING GUMMIES Longboard Tyres are a 'Revolution' in the boarding world! The GUMMIES Wheels are so good its as if the Longboard wheel has just been re-invented! Measuring 50x 125mm or 3.75x 5 Inch & made from Super Soft / High Re-Bound premium Urethane the GUMMIES Longboard Tyres will fit too & transform the performance of TRAMPA's 3.75x2 Inch HYPA, SUPERSTAR or MEGASTAR 8 hubs, converting regular pneumatic wheels into Supersized Longboard-style wheels giving a completely new sensation when riding your board!

Being 125mm in Diameter the GUMMIES Tyres are much larger than any other Longboard wheel on the market. Produced using SUPERSOFT (75a-78a) Premium Urethane & the same 50mm wide surface contact as the TRAMPA Stickies Longboard wheels, the GUMMIES Tyres perform like their name suggest & when ridden on fresh tarmac / asphalt or smooth Hard Packed surfaces like a go kart track, once warmed up the GUMMIES Tyres literally stick like 'XXXX to a blanket' allowing the most insane turns & carves that you would not believe were possible.

Available in Black, Blue or Red, the Super Soft /High re-bond Premium Urethane we have used allows the GUMMIES Wheels to glide over cracks in the pavement & smash through the small obstacles that often get in the way when cruising around town, potentially jamming up smaller sized longboard wheels which can be well scary when it happens!!

Boarding of all kinds has recently seen a massive revolution with many new riders coming on the scene adding electric motors & powerful batteries to their boards, you could say much of the equipment being used by other brands is just not up to the job,  riding small wheels on high speed electric boards can be frightening and well when you hook up the TRAMPA GUMMIES wheels onto one of the new TRAMPA Electric Boards, the GUMMIES tyres performace comes into a whole new universe of riding experience that nobody ever knew existed before...!! All of TRAMPA's electric boards are all incredibly powerful, just the most un-real performance is experienced like nothing else ever.... Honest! Fitting a set of GUMMIES to 16 Inch wide ATB Spring Trucks in place of off road tyres converts your Mountainboard into a Street Monster, Racing around places like go-kart tracks will soon become the latest thing too do & we know the mega grippy GUMMIES tyres will become the #1 choice of all serious high speed riders.....

44-tooth Slave Pulley fits to the HYPA, SUPERSTAR & MEGASTAR Hubs and should be used when fitting the GUMMIES tyres into your Electric Board. GUMMIES tyres also fit to Electric Longboards & Carveboards

Sets of 4 GUMMIES Tyres are available at a discounted price at this link

TRAMPA's 14FiFties Open Belt Designed Motor Mounts are ORRSOM! With breath-takingly good looks & super strong performance to match, the 14FiFties Baseplate is presented to you in a pelethera of bright anodised colours for you to choose from when making your purchase & being 14 Inches wide the over-sized Longboard style trucks are not the widest there are, supplying enough space

Offering 13-15 tooth gearing options on the motor side & harmonious gearing to match on the chosen slave wheel, there are endless setup options for all kinds of rider & terrains.

Whether you set up with giant sized 125mm GUMMIES Longboard wheels, the super sporty 165mm URBAN TREADS pneumatic Tyres or if your more likely to want to go more comfort or off road ability choosing the 7 or 8 Inch Pneumatic Wheels,  14FiFties Longboard trucks are pre-fitted with 12mm Axles 


This simple motor mounting kit is as versatile as they come - working flawlessly with our 12-FIFTIES Longboard Trucks, as well as other brands’ trucks and wheels..

The Motor Mount Connectors snuggly slide over the truck hanger and are secured tightly with MARINE GRADE M6x10 grub screws. The Premium Quality Carbon Mounting Panel is sandwiched tightly between the Motor Mount Connectors, & is fitted with a support for long motor axles. The Motor Axle Support houses a precision 608 bearing, supporting axle rotation & ensuring the motor is as secure & efficient as possible. TRAMPA’s motors have a longer axle, that fits perfectly into this support.

The Pulley Kit includes a 15mm STRONGBELT and a choice of Slave Wheels, that can drastically change the performance of your finished board. We use a 15mm wide reinforced drive belt that reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. This kit can fit a variety of different Slave Wheels, for fitting STICKIES, GUMMIES or URBAN Wheels - each changing the style & performance of the finished board.

TRAMPA's very own purpose made 118kv & 136kv Fully HALL & TEMPERATURE Sensored Out-Runner Motors are custom made to handle high-voltage set ups! These motors easily outperform all the competition on the market in so many aspects & its list of applications is almost endless! Our special design allows you to also fit metal mesh filters to prevent the impregnation of larger particles ending up in your motor!

In this kit you get the following items -
1x 14Fifties Longboard Truck 66 TOOTH MOTOR MOUNT - GOOFY
1x 14Fifties Longboard Truck 66 TOOTH MOTOR MOUNT - REGULAR
1x Belt Tension Roller Housing for 15mm Belts - SILVER
1x TRAMPA 608 Skate Bearing
1x Sprung Steel C-CLIP for secures bearing in Belt tension roller
1x Step SPACER used for positioning tension roller
1x M6 x 25mm HEX Head Bolt - Marine Grade Stainless steel
1x M6 Nut - Marine Grade Stainless steel Nylock nut
1x M6 Washer Form C - Marine Grade Stainless Steel
2x OBD Motor Adaptor with Housed Bearing
2x M4 x 8 Socket Cap TORX Bolt
16x M4 x 10 Dome Headed TORX Bolt
2x M4 x 18 Socket Cap TORX Bolt
2x M6 x 25 Socket Capped TORX Bolt
2x 44 Tooth Slave Pulley - HYPA or SUPERSTAR/MEGASTAR - URBAN Motor Mounts
2x Custom 15mm wide Motor Pulley 13, 14 or 15 tooth
2x M4 x 4mm Grub Screw Motor Pulley
2x KEYWAY for Motor Pulley & Axle Shaft - 3x 3x 8mm
12x M4 x 40 Socket Cap Allen-Key Stainless Steel Bolt
2x 350 x 15mm Belt - Gummy Carve & ORRSOM using 44 tooth Slave
2x TRAMPA Custom DC Motor 6364 6376 6386 - SINGLE
2x Star Shaped Filter Holder Allows air & prevents dust!
2x Motor Filter - End fits 63mm size Motors
2x Motor Filter - Wrap Motor fits 63mm size Motors
22x M3 x 4 Dome Headed Allen-Key Stainless Steel Bolt
2x HALF CAGE Motor protection Housing - Aluminium
2x HALF CAGE Stainless Steel Motor protection FILTER - BLACK
2x Star Shaped Filter Holder Allows air & prevents dust!
2x Motor Filter - End fits 63mm size Motors
10x M3 x 4 Dome Headed Allen-Key Stainless Steel Bolt
2x 14FiFties Hanger 355mm with 12mm HOLLOW Steel Axles
2x 12 & 14 FiFties Truck BASEPLATE
2x Pivot cup for TRAMPA Skate Trucks - Inspect & replace regular
2x 12 & 14 FiFties Truck Baseplate Adaptor
2x 12 & 14-FIFTIES & TRAMPA-IR Trucks KINGPIN
2x 3/8ths Inch Axle Nut - Stainless steel Nylock HALF nut
2x Custom Blood Orange BARREL Bushing
2x Custom Blood Orange PLUG BARREL Bushing
4x CUPPED Washer for SKATE BARREL Bushing - NIKLE
4x ATB HOLLOW Vertigo 12mm Axle 114.1 (51.1 + 10.5)
4x 12 x 18.2mm Wheel Support axle Spacer
8x 12 x 16 x 1mm PRECISION Shim Ring
4x 7/16ths Half Nut - Marine Grade Stainless steel & Nylock
4x HYPA Hub 3.75x 2 Inch - Any Colour you like!
24x M4 x 35 Socket Cap Allen-Key Stainless Steel Bolt
24x M4 Nut - Marine Grade Stainless steel Nylock Nut
4x GUMMIES 5 Inch Tyre 3.75x 2x 5
Weight: 6,100g
Quantity required:
We have enough parts to make…  
RRP £825 - for the complete set

Excluding VAT
HCC: 8302300090

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon