This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

Pre-Configured - Full Power - Spur Gear Drive Electric Mountainboard

Pre-Configured - Full Power - Spur Gear Drive Electric Mountainboard Pre-Configured - Full Power - Spur Gear Drive Electric Mountainboard Pre-Configured - Full Power - Spur Gear Drive Electric Mountainboard 17ply 35° 9/69 TRAMPA Mountainboard Blank Deck - Fix the WINGS to the deck to add concave & the increase the width of the deck 2WD FRONT Truck Mounting Kit TRAMPA 35° 9/69 2WD Electric Mountainboard Deck with WINGS - WINGS give safe cable routing, adds W Shaped concave & the increase the width of the deck from 9 to 10 Inches - 17ply FULL CNC SAVAGE ATB TRUCK from solid Billet ALLOY, fitted with solid CRMO STEEL Axles & Kingpin - SILVER SILVER Uprights & BLACK Crossbar BULL BARS for CARVE BOARDS using T6 Heat Treated CNC'd Aluminum Clamps, Hollow Aluminium Stash Tubes with Rubber end bungs Mountainboard Spur Gear Drive TWIN Motor Mount with PULLEYs - NO Motor, NO Filters Pre-Configured - Full Power - Spur Gear Drive Electric Mountainboard 6386 165Kv 3800w DC Brushless & SENSOR-LESS Motor HALF CAGE Motor protection  - SILVER anodised with Filters - TWIN Classic MONSTER Box with Mounting Panel to fit 2x VESC 6 VESC 6 HP - HIGH POWER PCB VESC 6 HP - HIGH POWER PCB VESC 6 HP - HIGH POWER PCB VESC 6 HP - HIGH POWER PCB VESC 6 HP - HIGH POWER PCB VESC 6 HP - HIGH POWER PCB VESC 6 HP - HIGH POWER PCB VESC 6 HP - HIGH POWER PCB VESC 6 HP - HIGH POWER PCB VESC 6 HP - HIGH POWER PCB Pre-Configured - Full Power - Spur Gear Drive Electric Mountainboard VESC Connect NRF Wireless Dongle - INTERNAL Antenna NRF Dongle Extender cable 200mm - VESC 6 CANBUS Cable 24 AWG  Silicon Yellow/White - 200mm 6s 22,000mAh Zee Li-Po Cell PHATLADS 5 spoke OFF-SET Hubs 3.75/4 x 2.5 Inch - Natural BLACK & Marine Grade Stainless Steel Bolt kit TRAMPA MUD-PLUGGER 8 Inch Tyre measure 3.75x 2x 8 Inch or 200x50mm with 3.75 inch Rim fits all 3.75 inch Hubs - BLACK Pre-Configured - Full Power - Spur Gear Drive Electric Mountainboard 12mm Bearings - 12mm x 28mm axle ABEC 5 rated BLACK Rubber Sealed Sidewalls x4 Wheels Ratchet Bindings - Black straps on Black Foam with Silver L Brackets & Ratchets TRAMPA WAND MAGNETO Remote Control - VESC Based remote gives all the control you could ever wish for TRAMPA WAND MAGNETO Remote Control - VESC Based remote gives all the control you could ever wish for ULTRA POWER Charger with XT90 & Balance Cable Extensions Luxury Mountainboard Travel Bag - Fits 35º long decks with upto 9 inch wheels inc Motor Mounts & Monster Box perfectly! Also fits your charger, pads, helmet & beer! Luxury Mountainboard Travel Bag - Fits 35º long decks with upto 9 inch wheels inc Motor Mounts & Monster Box perfectly! Also fits your charger, pads, helmet & beer! Luxury Mountainboard Travel Bag - Fits 35º long decks with upto 9 inch wheels inc Motor Mounts & Monster Box perfectly! Also fits your charger, pads, helmet & beer! Luxury Mountainboard Travel Bag - Fits 35º long decks with upto 9 inch wheels inc Motor Mounts & Monster Box perfectly! Also fits your charger, pads, helmet & beer! 8 Inch Muck off bag Complete Deck TRAMPA Handmade VINYL Sticker Kit
From
£2,700+
schematic

flexometer

Pre-Configured: Spur Gear Drive - Full Power - Electric Mountainboard

 

Our Pre-Configured range has been carefully selected by our vastly experienced Trampa Team to provide a wicked set-up depending on your needs.

If you’re unsure about which options best suits your needs, don’t have time or simply want to leave it to an expert, we’ve got you covered with our Pre-Configured Boards!

 

The Range:

Basic - A solid all round option designed to be cost effecient and upgradable, while still retaining the trademark Trampa quality!

Full Power - If ripping down trails and maxing out that top speed is for you than choose the Full Power!

Long Ranger - With Premium choices throughout, the Long Ranger’s are designed to go there and back again (and again)!

 

SPUR GEAR DRIVE - FULL POWER

 

Deck - 17 Ply 9-69 Deck with Wings

Wheels - 8” Mudpluggers tyres sitting on our Phatlad Hubs is about as good as it gets, combining ultimate grip and weight to strength ratio

Trucks - Savage Trucks will hold strong at all speeds, while a single bull-bar stands at the front of the board

Battery Box - Upgraded with VESC 6 HP (High Power) the Classic Monster Box is ready for 2x 6s LiPo Battery cells creating 12s

Bindings - Ratchet Bindings and Heel Straps keep your feet nice and secure

Drive - Twin 6386 165KV Motors drive a 10/57 Steel Gear Spur Gear Drive System

 

17ply 35° 9/69 TRAMPA Mountainboard Blank Deck - Fix the WINGS to the deck to add concave & the increase the width of the deck


 

FULL CNC SAVAGE ATB TRUCK from solid Billet ALLOY, fitted with solid CRMO STEEL Axles & Kingpin - SILVER

 

Designed for those customers who insist on installing the very best, the strongest & highest performing equipment, well here now is TRAMPA's new 16.5 inch wide SAVAGE hanger, the best we have made yet!

Visibly the SAVAGE Hanger looks very much the same as the regular ATB Spring Hanger, to fit to the Baseplate & connect with the springs & Barrels that need to be fitted it has to be similar, so the differences or improvements you could say are subtle, for instance instead of being produced from forged alloy the SAVAGE Hanger is produced from a solid billet a premium alloy & entirely CNC to shape, but you could not tell on the surface.

The SAVAGE Hanger is also considerably beefed beefed up in all the critical areas compared to the original forged alloy spring truck. With CNC cut outs & trims in all the non-critical or most importantly structural areas, increased strength over the original has been achieved whilst to save weight excess material has been removed as much as possible. In the same breath the base of the hanger has been given an extra couple of millimeters of thickness giving huge extra structural strength & finally the SAVAGE Hanger has been Seriously Re-enforced around the kingpin area & installed with super strong SOLID 12mm CROM-MOLY Steel AXLES! 

The SAVAGE hanger measures 16.5" wide, which is half inch wider than the originals making this Hanger the obvious choice for the largest or hardest of riders out there!
In the accessories pages

 

 

Ratchet Bindings - Black straps on Black Foam with Silver L Brackets & Ratchets

RATCHET BINDINGS are the Mountain Board rider’s primary choice of binding! The Ratchet Buckle mechanism allows you to easily position the binding to fit most adult sized shoes or boots. There is a release clip on the top of the Ratchet Buckle which works just the same as snowboard binding does, that release the pressure & allows you to step out...

The main Foot-Strap has a special 'Lug or locator' on the top of the Foot-Strap to house a special Hook that protrudes from the underside of Ratchet Buckle. This hook presses into the 'Lug' on the top of the Foot-strap preventing any sideways movement in the connection of the Strap & Ratchet Buckle

The Ratchet Buckle connects with a special M5 Star nut & M5x8mm Countersunk bolt & the Ratchet is mounted on the top of the Main Foot Strap. The LADDER STRAP Positions on the outside of the foot & feeds into the Ratchet Buckle. Levering the Ratchet buckle brings the two straps together. The Ratchet Buckle locks each time you lift the buckle tightening the two straps together until you have a snug but not tight connection over the top of your foot. The release clip can be tuff to move specially of your bindings have been ratcheted tight.

Ratchet Bindings work at their absolute optimum when combined with TRAMPA Heel StrapsHEEL STRAPS Completely lock your feet into any of the TRAMPA bindings to make you feel at one with the deck. When using Heel Straps you are 100% committed to the ride & by doing so you gain so much more control over the board.  

With 3 pairs of different length Ladder Straps to choose from, the TRAMPA Heel Straps easily adjust to fit to any sized shoe that comfortably fits onto a Mountain Board . A CAMLOCK BUCKLE on one side of the strap is used to Lock the Ladder Strap on one side of your foot whilst a Ratchet Buckle is used on the other side for easy tightening/loosening adjustment. The Ratchet Buckle easily tightens the Ladder into the Heel Straps so that your foot is locked into a comfortable position!. 

TRAMPA Heel Straps are universally fitting and are supplied with a Marine Grade Stainless Steel FITTING KIT as standard, so only take a few minutes to assemble. 

ALL TRAMPA Bindings are assembled using a Marine grade A4 Stainless Steel hardware. The L-Brackets are 'multi positional' allowing the rider the exact foot-stance they require.

All TRAMPA bindings use Stainless steel Dome Headed Bolts, connected through the Footstrap into L-Brackets, ensuring no discomfort to the foot. 

The L-Brackets are 'multi positional' allowing the rider the exact foot-stance they require 

TRAMPA's huge range of bindings are the most customisable on the market - meaning you’ll be able to get the perfect fit for your riding style - in any colour scheme you can think up.   

VESC 6 HP - HIGH POWER PCB

Introducing the amazing VESC® 6 MKVI HP (Higher Power) Speed Controller, the sixth major product update of the world famous VESC 6 motor controller with some extra punch on the top end. Packed with a variety of amazing new features, this VESC motor controller is certainly worthy of its pimpin’ gold logo, pushing up to 160A burst reliably towards your motor + allowing spikes to surpass 200A. This device is ideal for those who need a lot of power for a short period of time - perfect for Hydorfoils and other demanding applications.

The second VESC controller capable of hibernating, your board can conserve power while not in use - reducing power consumption to just 20μA – less than the self-discharge rate of the batteries. Or with automatic power off, your VESC controller can switch itself off after a set amount of time.

No more loop keys! Compatible with power buttons / switches, the VESC 6 MKVI controller can be ready to go with a single press / flick. If desired, multiple devices can share a single button.

Roll-to-start – it’s possible to set your board to power up with a small kick/nudge! The MK VI iteration now allows you to disable this feature.

In its development, no Mosfet switches were used - due to their tendency to eventually blow up one day. This saves on the additional costs of replacing them, & also adds to the longevity of the VESC 6 MKVI.

When we developed the VESC 75/300 controller, it was obvious that most of its features would be handy to have in the VESC 6 controller format.  As a result, Benjamin Vedder took on the challenge and re-designed the entire PCB of the VESC 6 controller, to make new, powerful features available in a smaller & cheaper 60V rated package.

The VESC 6 MKVI controller features THREE PHASE SHUNTS & adjustable CURRENT / VOLTAGE FILTERS - detecting any motor attached more precisely and reliably than ever before. Consequently all kinds of motors now run as smooth as butter & react PERFECTLY LINEAR to throttle input commands.

You’ll also find an IMU chip fitted - featuring a gyroscope, accelerometers the VESC 6MKVI knows its 3D orientation in space, 3 axis acceleration values. 

UAVCAN has been added to the firmware allowing to interact with commonly used flight controllers like the PIXHAWK ®* devices. An incredible 12,000 lines of code have been added for the new hardware releases. To make the VESC controller nearly indestructible, the low voltage rails were redesigned A-Z.

VESC-Tool software is now available as an Android™ and iOS™ compatible App, allowing you to configure your VESC or VESC controller array with only a few clicks. User specific PROFILES will let you change in between different setups with a single tap on the fly.

Using an original VESC 6 MKVI controllermotor detection is now more precise than ever. Extreme low inductance (0.5 μHmotors are no issue! 

Parameters for gearing and wheel diameter have been added, allowing display of speed, Wh usage per distance travelled, precise battery indicator, current consumption, duty cycle and power. Beautiful self-adjusting analogue displays make the readings of all parameters very enjoyable.

What makes the original VESC hardware so special?

The original hardware is perfectly matched to work seamless withe VESC-Tool software code. Both, hardware and software, have been designed by the same engineer, knowing all critical detail.

Features

- Current and voltage measurement on all phases (three phase shunts)
- Adjustable current and voltage filters
- built in IMU chip (accelerometer, gyro)
- Regenerative braking
- Traction control (single and twin setup)
- Sensored or sensor less operation + hybrid mode, HFI and sildent HFI
- 100% torque from 0 RPM without sensors (for most salient BLDC motors)
- highly accurate sensorless position control (for most salient BLDC motors)
- Configurable RPM-, current-, voltage- and power limits
- Input source: PPM, Analog, NRF Nyko Kama Nunchuck
- Communication ports: USB, CAN,UAVCAN, UART
- Throttle curve and ramping for all input sources
- Separate throttle curves for acceleration and brakes
- Seamless 4-quadrant operation
- Motor revolution, amp hour, watt hour counting
- Display of speed, power, duty cycle, amp flow, estimated range and battery status on App
- Accumulated data from arrays of VESCs
- Real time data analysis and read out via communication ports
- Real time data analysis and read out via VESC-Tool APP or VESC-Tool software
- Adjustable protection against:

          -    Low input voltage
          -    High input voltage
          -    High motor current
          -    High input current
          -    High regenerative braking current (separate limits for the motor and the input)
          -    High RPM (separate limits for each direction).
          -    Over temperature (MOSFET and motor)

Technical Data Sheet

- Voltage: 11.1V – 60V (Safe for 3S to 12S LiPo).
- Voltage spikes may not exceed 60V!
- Current: Continuous 80A, Motor current max 160A, Spikes 210A.  Values depend on the temperature and air circulation around the device!
- 5V 1A output for external electronics
- 3.3V 0,5A output for external electronics
- Modes: DC, BLDC, FOC (sinusoidal)
- Supported sensors: ABI, HALL, AS5047

* Android is a trademark of Google LLC.
Google and Play Store are trademarks of Google LLC.
iOS is a registered trademark owned by Apple Inc.
PIXHAWK is a trademark of Lorenz Meier

Mountainboard Spur Gear Drive TWIN Motor Mount with PULLEYs - NO Motor, NO Filters

TRAMPA WAND MAGNETO Remote Control - VESC Based remote gives all the control you could ever wish for

Introducing the Amazing WAND CONTROLLER

Frank Drenckhahn - King of design & production at TRAMPA & Benjamin Vedder - Creator of the VESC aka the 'Yoda of Electronics', spent the winter period of 2018/19 designing a revolutionary remote controller, with some new & very exciting 'E-Skate-specific-features' to work in direct relation with the VESC / TRAMPA series of products.

There are many basic remote control options already on the market, but none of them hit the high bar when it comes to features & reliability. Here at TRAMPA, we’ve experienced riding with in-sufficient, untrustworthy remotes. Consequently, we’ve always dreamed of holding a reliable, versatile, ever-lasting, informative & safe remote controller, that matches the outstanding performance of the VESC software & the TRAMPA equipment that they’d be so frequently paired up to. You should expect nothing less than magic whilst waving the WAND over TRAMPA assembled VESC Products!!

HARDWARE

High-end TRAMPA Electric boards deserve to be controlled with a high-end remote, you need to be 100% in control over the Monster under your feet! Personally, I always dreamed of something that feels nice in your hands, made of high grade material, with a little bit of weight to represent the same high quality level of our TRAMPA boards, and the cutting edge technology the VESC offers. This remote is made from 6061 T6 (Aero-grade) Aluminum with a sleek carbon fiber battery lid. You can see & feel the quality straight away.

REAL TIME DATA DISPLAY

The WAND is fitted with a circular high resolution OLED display that reveals all the crucial information you want to have at hand while riding your board. The screen might be small, but the list of data it shows is HUGE! You’ll be able to scroll through and see your current speed, average speed, amp draw, duty cycle, average watt hour draw, battery indicator (for both board & remote), recuperation and more to be added through firmware updates!

Whatever data the VESC captures can ultimately be displayed on the OLED screen. Benjamin even added in a few tools to display animated graphics, for ultimate pimpness!

SMART REVERSE

Ever over shot the junction & wished you could reverse a little to pull you back from the traffic? Well now with the WAND in your hand, pulling back on the Thumb Controller bringing you to a stop & keeping your thumb in the braking position will automatically instigate the Smart reverse feature which will ramp up enough Amps to switch the rotation direction of the motor but just at slow speed so that the board reverses you out of trouble..... A very very clever feature designed to keep our clients safe...

SAFETY & GESTURE Control: AN OUTLOOK TOWARDS FUTURE FW UPDATES

What is really exciting is the IMU (Inertial Measurement Unit) inside The WAND... The IMU knows the exact orientation of The WAND in space and gathers acceleration values of all the space axis at the same time, acceleration, speed & elevation. Using the IMU, Benjamin will in future be able to code some really useful safety features, as well as some playful things. For instance; one day the remote will be able to tell if you take a tumble & will be able to stop your board safely. It will know when it is resting upside down on a surface, and refuses to send accidental signals to the board. Powering up when you pick it up & going to sleep after 5 minutes of inactivity The WAND is smart enough to save its own battery! It can even be used as a water spirit level, helping you to align things perfectly! Expect some nice FW updates in the FUTURE. IMU features will become available over a period of time!

TRANSFORM YOUR REMOTE

On top of the features mentioned above, amazing piece of tech features the options to either be converted to a pistol grip style trigger remote, or to have an additional small trigger on the lower side to allow additional index finger control. I like to use my index finger to send acceleration commands, while using my thumb to send brake signal commands. Others want to use their thumb or index finger only. Much alike TRAMPA’s boards, these remotes are made to be customised around you!

SAFE KEEPING

We’ve all wasted too much time on the pre-riding ritual known as “Where the **** did I leave the remote?!” Well no more. We decided to equip The WAND with a Magnetic bottom panel. A small metal sheet or magnet attached to your board (stick a big washer to your Battery Box or similar), will keep your remote safe where it belongs all the time, or you simply keep your remote on the fridge, next to the car keys! 

BATTERY LIFE

Battery life has always been an issue in the past. Sometimes you want to go out for a ride, but you forgotton to charge up your remote. Then after a quick charge, you end up worried that it‘ll die before the end of your ride.

When Frank & Benjamin designed this remote, ultra low energy consumption was a prime goal to achieve.

We chose to use standard AAA batteries, so that you can easily carry spares & swap them out - like changing the batteries on your TV remote, giving you ultimate confidence that you will never ever run out of battery. Two tiny AAA cells are good for 30 hours of constant operation. AAA cells are available at gas stations, supermarkets, drug stores, or even in a remote house in the middle of nowhere in a kitchen draw, should you get real desperate while out on your endless trails!

SOFTWARE & SUPPORT

We don't want you to have to buy a new remote because the software becomes outdated, so we made sure this remote would have a USB & SWD port, allowing you to easily flash the latest firmware, and unlock the latest features when they get released. This remote is future proof & will surprise you many times over its life. The Wand Firmware will be Open Source. Please browse Benjamin Vedders Github for source files and copyright information : https://github.com/vedderb

COMPATIBILITY

This remote is fully compatible with the TRAMPA NRF Dongle. An NRF connection is required to pair the Controller to the VESC device. Depending on if or when you bought the dongle, you might need to update its firmware in order to make the connection to the controller though the VESC, which is a simple task. This remote is compatible with any ESC that is based on VESC technology, and running the VESC firmware. Simply plug the TRAMPA NRF Dongle into the UART port of your ESC.

CALIBRATION AND MULTIPLE BOARDS

This remote doesn't require calibration. A simple one click pairing procedure does the trick. This remote will become a solid partner to all your boards.  No more need for multiple remotes for lots of boards, unless you want to ride out with your friends. In which case you can leave your old PPM remote receiver plugged in & switch over to that using the VESC-Tool App.

In order to connect The WAND to your VESC or VESC based ESC, you will need to do a Firmware update on that ESC. Simply plug the TRAMPA NRF Dongle into your VESC & pairing is pretty much automatic, just follow the on-screen instructions. The TRAMPA NRF Dongle can be updated to the latest, compatible FW, using the latest desktop VESC-Tool.

Technical features for the WAND;

- Stable & safe with NRF wireless connection

- High resolution OLED display

- 2x AAA standard size battery which will give over 60 hours of battery life

- Exterior dimensions:144 x 31x 22mm

- Full Aluminum 6061 T6 SOLID CNC'd housing - Anodized Black with Laser Logo's

- Magnetic bottom panel. The remote sticks to metal surfaces for safe keeping.

- Easy connectable to thousands of devices

Modes that the WAND can control;

- Forwards

- Brake

- Reverse

- Cruise Control

- Pre-programmable to allow you to select between performance setups so you can switch between defined user profiles. Adjusts power levels, acceleration, top speed brakes performance. Define Profiles for Learner, Intermediate & Advance riders who will all prefer different setup's

OLED Display will show you;

- Current Speed

- Average Speed

- Amp Draw

- Battery status of Remote

- Battery status of Board its connected too

- Duty cycle

- Estimated range

- Watt Hour Consumption

- Many many more features yet to be written about :-)

Saftey;

- Shock sensor (will become available via future Firmware update)

- No signal when remote is turned head over (e.g. trigger resting on surface)

- Safe NRF based wireless communication

- Safe pairing to board

- No calibration needed

- No interference with other remotes (group rides)

- Auto power off, auto power on

- Regular firmware updates available

ADDITIONAL FEATURES

- Your Android Phone or Mobile device with the VESC App & the WAND remote will share the same connection to VESC giving seamless connectivity.

- Firmware can be updated via VESC-Tool

- Works with existing TRAMPA NRF Dongles (Dongle may require a Firmware update)

- Different size triggers to fit different sized fingers

- Can be transformed to be a 'Finger Trigger' style remote where an additional feature of adding a Handle for comfy holding

- Can be transformed to have 'Thumb Stick' & 'Small Trigger' on lower side (use index finger for acceleration and thumb for brakes)

- Built in IMU (gyro and accelerometer) Be surprised what magic this can do in the future.

ULTRA POWER Charger with XT90 & Balance Cable Extensions

Using the ULTRA POWER Charger It is possible to charge & balance 2x Batteries packs up to 12s in size at the same time...

SO for example if you have 2x Electric Boards in your collection, (lucky boy) if they are both running a single 12s pack (i.e. 2x 6s 22000 mAh HRB Cells in the MONSTER Box or 6x 2s HRB 10, 12 or 16000mAh in the Underboard Battery Tray or the BEAST box'sthen you can fast charge & balance 2 x Boards at the same time or if you only have 1x Board but you are running 2x 12s packs (i.e. 4x Zippie compact cells fit directly into the Monster Box using a Graupner charger you can only charge 1x 12s pack at a time so you will need double the time to charge 2x 12s packs if you have 4x Zippies cells unless you purchase another Graupner charger so you can then charge both cell packs at the same time -  if this is the option you have selected, then it is also possible to boost the speed of the charge of your 2x Graupner chargers by placing a Booster charger before them) then this is the deluxe charge for you.

This charger is terribly expensive but it is everything the 2x Graupner chargers with a Booster box option tries to be. It can charge incredibly fast up to 15A, it has an internal booster with amp adjustment for charging & Balancing all kinds of cells. The best part about this charger is that you simply plug it in & it knows the cells you have, Its possible to mix up the balance cable connections when plugging in for the first time but it alerts you to this &you simply swap over the cables & it knows... (best practice is to mark the balance cables so you know in the future which one goes into which port without having to exchange them each time for guessing wrongly lol) simply select the amount of Amp charge you wish to put into it by pressing the select button (a low 2A charge will balance your batteries beautifully but will take a long time to do, where as turning the charger up to 15A will give you a fast boosted charge,  which is great if the weather is amazing & you cant get enough riding on that day but its not good practice to fast charge your cells all of the time, so only fast charge when you don't have time to wait for a nice balance charger, but selecting a low to mid power option on a regular basis will keep your cells in the best operating conditions), 

The ULTRA POWER Charger is not supplied as standard with Balance extension cables or XT90 Cables to plug into your batteries. We have acquired some Balance extension cables and have also made some nice 30cm TRAMPA Silicon charge cables with XT90 connectors on to make charging with the ULTRA POWER Charger to be really easy & fiddle free. The Cable kit is available at a discounted price when purchased with the ultra power charger, however the extension cables can be purchased anywhere on the internet and its not rocket science to make your own extension cables if you have the time to do this & will of course save you a few quid in the mean time.

This Special ULTRA POWER Charger for the Complete TRAMPA Electric Boards comes Supplied with a complete ULTRA Power Charger Cable Extension Kit which makes plugging into your board really easy & so much less fiddly than the shorter cables it comes with PLUS it comes with either UK or EURO wall Plug (sadly no US Charger plug option but a simple world wide adaptor plug will do the trick to convert it). Please select your wall plug option below.

Luxury Mountainboard Travel Bag - Fits 35º long decks with upto 9 inch wheels inc Motor Mounts & Monster Box perfectly! Also fits your charger, pads, helmet & beer!

Arrive like a Pro with a Tailor made LUXURY TRAVEL BAG. This quality bag is the perfectly sized to fit your fully assembled 35° with 8 inch wheels into.

On the exterior, the Luxury bags Double Strength Chunky Zipper, un-zips all the way round to allow easy entry for the board. The LUXURY TRAVEL BAG is padded with 10mm EVA foam at the top, the bottom & at the sides to protect your board from impacts during transit. Top quality Stainless Steel Zippers, pimped out with custom made TRAMPA Zipper Pulls, makes zipping & un-zipping the bag a total pleasure. For your security whilst traveling your bag is supplied with a Padlock & key.

CHUNKY CARRY HANDLES join at the side of the bag & with the use of a velcro strap they connect comfortably together. Brushed Aluminum Quick Release Dog Clips attach or remove the Double Padded & Adjustable length Shoulder Strap, making carrying it down the beach or through the airport as comfy as possible. There is also a quick access Exterior Travel pocket for storing documents and the likes & Re-Enforced Grab Handle at the end of the bag to assist in lugging the bag around.

The interior of the bag is lined in strong Nylon making slipping your board into the bag very easy to do. It also has Super-long Velcro Pockets that run the entire length & depth of both sides of the bag, allowing you to be able to safely store your Bar & lines within. Steady straps wrap over the deck, anchoring it in place to avoid rolling around, making it more comfortable to carry.

The Luxury Travel Bag is best used in conjunction with the TRAMPA MUCK OFF BAG, as its name suggests, it keeps the muck off & keeps the Luxury bag clean!!

Complete Deck Weight

Deck Ply
Blank Deck Weight
Component Weight
Complete Deck Weight

Component Weights

FULL CNC SAVAGE ATB Truck - SOLID CRMO Axles - SILVER1,736g
BULL BARS for CARVE BOARDS - SILVER / BLACK249g
SGD Motor Mount with PULLEYs - NO Filters or Motors2,308g
6386 165Kv 3800w DC Brushless & SENSOR-LESS Motor 1,830g
HALF CAGE Motor protection Filters - TWIN SILVER192g
Classic MONSTER Box fits 2x VESC 6 internally 1,251g
VESC 6 HP - HIGH POWER448g
VESC Connect NRF Wireless Dongle - INTERNAL Antenna 4g
6s 22,000mAh Zee Li-Po Cell5,140g
PHATLADS 5 spoke OFF-SET Hubs 3.75/4 x 2.5 Inch - Natural BLACK936g
TRAMPA MUD-PLUGGER 8 Inch Tyre 3.75x 2x 8 - BLACK1,416g
TRAMPA 6001 2RS Mountainboard Bearings BLACK x4 Wheels184g
Ratchet Bindings - BLACK straps & Foam Silver L Brackets & Ratchets525g
Total component weight16,219g
FULL CNC SAVAGE ATB TRUCK from solid Billet ALLOY, fitted with solid CRMO STEEL Axles & Kingpin - SILVER
Ratchet Bindings - Black straps on Black Foam with Silver L Brackets & Ratchets
TRAMPA 35° 9/69 2WD Electric Mountainboard Deck with WINGS - WINGS give safe cable routing, adds W Shaped concave & the increase the width of the deck from 9 to 10 Inches - 17ply

Blank deck weight chart

Deck Ply
Blank Deck Weight
General Flex Rating
----------------------------------------------------
 
TRAMPA's SPUR GEAR DRIVE Electric Mountainboard is sensational to ride. Using a high gear ratio (potential of 1/7), it has an acceleration performance similar to that experoenced when riding motor cross bike & is the perfect option if you wish to accelerate incredibly fast, go across rough terrain & climb the steepest of hills around you.

----------------------------------------------------

Light weight riders are good using the Light weight POM Slave Pulleys, but if you are a big guy, say over 85kg then you should seriously consider paying the extra & taking the heavier Steel Pulleys, as these are MUCH stronger & can for sure handle a lot more abuse being thrown at them than the POM pulleys, which have seen heavier guys shred teeth from wanting too much fun!!

GEARING OPTIONS to Suit all riders

10T STRAIGHT Cut
Motor Pulley / 58 Tooth POM Slave Pulley - Gearing ratio 1-5.9
10T HELICAL
Cut Motor Pulley / 58 Tooth POM Slave Pulley - Gearing ratio 1-5.8
10T HELICAL Cut Motor Pulley / 57 Tooth STEEL Slave Pulley - Gearing ratio 1:5.7
9T  HELICAL
Cut Motor Pulley / 63 Tooth STEEL Slave Pulley - Gearing ratio 1-7

----------------------------------------------------

Adding 9 inch wheels at the rear of your board will increase grip considerably in soft conditions & give you an increase on top speed of around 3mph!! It all depends on how hilly it is around you, how heavy a rider you are and the kind if riding you like to do as to whats best, the best thing with TRAMPA products is that you are never left without options if you want to change the performance somehow.... Speak to the team support@trampaboards.com if your not sure...

----------------------------------------------------
 
TRAMPA's LOADED Boards are sold to you FULLY Assembled & arrive to you In a Muck off bag, thats strapped into a Luxury Travel Bag, with absolutely everything you need fitted & fully tested with the correct BEST Charger sent with it as standard.

You get Everything except Batteries....!!

Its just about impossible for us to be able to send our boards with batteries in. We are able to sell & install them for you if you are to collect from Nottingham, but the size and power capability of the pack makes it very tricky (Desperately expensive) to ship.

 
----------------------------------------------------

WARNING!!!
Mountainboarding, Longboarding, Electric Mountainboarding, Kiteboarding, Skateboarding, infact any version of boarding of any kind, is dangerous. Accidents are deemed as 'Part of the fun' & are most likely inevitable.
To limit injury in the event of an accident, it is advised that you should wear as much protective clothing as you can bare to wear in an attempt to protect yourself from injury.
When miss-used, all kinds of bizarre & exceptional accidents  could & do happen, any of which could easily result in death. So always take care & never takes risks if you are not prepared to bare the consequences. You, the rider, is & are 100% fully responsible for your actions & or any accidents that may occur from riding any TRAMPA BOARD.

----------------------------------------------------

----------------------------------------------------
A Board like this is best ridden off road, away from traffic enjoying the countryside, exploring dirty routes you have seen when driving & have only ever dreamed of riding before....
 
Please ride away from Traffic & not towards it.
 
You should never ride on the roads & most importantly, if you have to ride on roads that you always ride well away from any traffic. Hitting any moving object whilst riding any kind of skateboard will most likely result in death, so we advise you don't do it. Anyway in most countries around the world it is still illegal to ride the devices we sell on the roads or highways & it has been herd of that crime busting Police from all around the world, do in fact have the power to even confiscate your device if its being used in the wrong place, so always be respectful when negotiating with the authorities over legislation of whats right or wrong & drop your right to ride the roads as a matter of your own safety.... Here in the Uk we have no rights to ride on the roads so let that be a warning.

If there is no cycle path for you to ride then please choose to ride the sidewalk or pavement instead of the road & then take your time & steer well clear of anything that's moving... Give way to all pedestrians, most of them have ear phones in these days & quite often do not hear you coming so go steady & don't startle them by whizzing past them closely & in particular when riding off road look out for, give priority too & give plenty of space to pass dog walkers as they often have an excited animal pleased to see you at the end of a tether, which of course can easily get tangled with you & your equipment & well, lets face it nobody wants to hurt the doggie, upset the walker or impact the rider  negatively. 

Always expect the worst scenario to happen in all cases & we beg you to please never take a risk, its just not worth it.

----------------------------------------------------

Always ride with as much impact protect equipment as you can possibly bare to wear, accidents are inevitable & you are 100% responsible for your own safety at all time, so please check your board often for anything broken or loose & take care as you proceed on the board as these things are very powerful, dangerous in the wrong hands....!!!

----------------------------------------------------

This Electric TRAMPA Deck is constructed using the following components & parts...

1x 2WD TRAMPA ELECTRIC Mountainboard Deck with WINGS & Trims
2x FULL CNC SAVAGE ATB Truck - SOLID CRMO Axles - SILVER
1x BULL BARS for CARVE BOARDS - SILVER / BLACK
1x SGD Motor Mount with PULLEYs - NO Filters or Motors
2x 6386 165Kv 3800w DC Brushless & SENSOR-LESS Motor
1x HALF CAGE Motor protection Filters - TWIN SILVER
2x VESC 6 HP - HIGH POWER
2x 6s 20Ah Li-Po Cells
4x PHATLADS 5 spoke OFF-SET Hubs 3.75/4 x 2.5 Inch - Natural BLACK
4x TRAMPA MUD-PLUGGER 8 Inch Tyre 3.75x 2x 8 - BLACK
1x TRAMPA 6001 2RS Mountainboard Bearings BLACK x4 Wheels
1x Ratchet Bindings - BLACK straps & Foam Silver L Brackets & Ratchets
1x The MAGNETO WAND Remote Control gives total control!
1x ULTRA POWER Charger with XT90 & Balance Cable Extensions
1x Luxury Mountainboard Bag - Fits up to 9 inch Wheels!
1x 8 Inch Muck off bag
1x Complete Deck TRAMPA Handmade VINYL Sticker Kit

HCC: 9506911000
Are you a REGULAR or GOOFY Rider??
Are you a REGULAR or GOOFY Rider??

Im a REGULAR rider (Left foot forwards)
Im a REGULAR rider (Left foot forwards)

Im a GOOFY rider (Right foot forwards)
Im a GOOFY rider (Right foot forwards)


This board comes  EXACTLY AS YOU SEE ABOVE. 

This Board INCLUDES the BATTERIES in the price!

If you live outside of the UK or USA then the batteries will be shipped to you directly from the battery factory & you will need to install them when you receive them. USA customers will also need to install the batteries but they will be shipped from within the USA.

If you live outside the UK or USA there may be additional tax's or charges to pay when the batteries arrive with you.
 

If you live in Mainland England & Wales we can deliver your board with batteries no problem, if you live outside this are will have to ship the batteries from the Battery factory.
If you live in Mainland England & Wales we can deliver your board with batteries no problem, if you live outside this are will have to ship the batteries from the Battery factory.

I confirm i live in Mainland England or Wales

I confirm i live outside of England & Wales. I realise the batteries will be shipped from the battery factory & that there may be additional taxes to pay on the batteries when they arrive with me. (+£50)

Quantity required:
We have enough parts to make…  
From £2,700 - each

Excluding VAT

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

If your new to TRAMPA & fancy a board then the BUY NOW Range of decks make it very easy & come with everything you may need.... 

Once assembled, spun-up & tested at the factory, the Fully Loaded Board is packed into to a Muk-off bag, then slipped into a Luxury travel bag & is then shipped at an amazingly quick pace (2-3 days to almost anywhere in the world in most instances....) through UPS or DHL to almost anywhere in the world with delivery in

High quality boards deserve high quality accessories, which is why this board comes as standard with The WAND & the ULTRA POWER Fast Charger that will charge you from low to full in less than 1.5 hours.

Once arrived all you have to do is fit the cells you have already purchased  – easy!

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon