This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

BLACK PHATLADZ Deepdish hub with 9 Inch TRAMPA MUD-PLUGGER Tyre

BLACK PHATLADZ Deepdish hub with 9 Inch TRAMPA MUD-PLUGGER Tyre 9 Inch TRAMPA Mud-Plugger Tyre 9 Inch Re-enforced Inner Tube made by INNOVA - 225x65mm
RRP
£35
exc tax

How to put a wheel on an Infinity or Vertigo truck

How to put a wheel on an Ultimate Truck

TRAMPA's AMAZING 5 Spoke PHATLADS hubs are DEEP-DISH (Extra wide), OFF-SET & the latest addition to fit into TRAMPA’s amazing range of small off road wheels.

Injection molded using premium Dupont plastic composites, PHATLADS Hubs utilize a special 2 parts split-rim design that can fit any 6, 7, 8 & even 10” tyre that TRAMPA offers – One hub to fit them all will transform your ride experience for sure!

Measuring 65mm wide the PHATLADS hubs are a half inch wider than regular 8 inch TRAMPA hubs & are known as ‘DEEP DISH’ due to the Angle of the spokes on the fatter half part, allowing the wider Rim width to sit in the same axle space as a norrower hub, consequentially giving an 'offset bearing position'. Increasing the Rim width increases the ground contact of any tyres fitted to them giving a low wide look when the 6, 7 & 8 inch tyres are fitted & the PHATLADS Hubs are the perfect 65mm width fit for the larger 9 & 10 inch tyres to get maximum surface contact (GRIP) in the muddiest of conditions when contact is needed most!

Currently only available in Natural Black & White with Black Logos the PHATLADS Weigh just 226g per hub (not including the Marine Grade Stainless Steel hardware used to hold them together & fit them to the Pulleys) TRAMPA's PHATLADS are the lightest choice of hub for 9” & 10” Tyres.

There are two sets of Bolt holes running around the perimeter of the PHATLADS Hubs, these are Inner & Outer positions! The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the nut housings on the thinner of the 2 parts & once the 2 parts are mated together the Shorter M4x45mm bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. 

The Inner M4x50mm T20 TORX bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth Slave Pulley when fitted with 6 inch tyres, the 66 tooth Slave Pulley when fitted with 8 inch Tyres & 76 Tooth Slave Pulley when fitting 9 Inch tyres.... Having 2 sets of Bolt holes allows the user to be able to remove the wheel from the assembly without deflating & disassembling the wheel, meaning they can HOT-SWAP their wheel. Being able to 'Hot Swap' your wheels without taking them apart saves you lots of time when it comes to creating different rider setups, after all a board with 6 inch wheels is completely different to a board with 9 inch 

It is possible to fit both the

TRAMPA's AMAZING 5 Spoke PHATLADS hubs are DEEP-DISH (Extra wide), OFF-SET & the latest addition to fit into TRAMPA’s amazing range of small off road wheels.

Injection molded using premium Dupont plastic composites, PHATLADS Hubs utilize a special 2 parts split-rim design that can fit any 6, 7, 8 & even 10” tyre that TRAMPA offers – One hub to fit them all will transform your ride experience for sure!

Measuring 65mm wide the PHATLADS hubs are a half inch wider than regular 8 inch TRAMPA hubs & are known as ‘DEEP DISH’ due to the Angle of the spokes on the fatter half part, allowing the wider Rim width to sit in the same axle space as a norrower hub, consequentially giving an 'offset bearing position'. Increasing the Rim width increases the ground contact of any tyres fitted to them giving a low wide look when the 6, 7 & 8 inch tyres are fitted & the PHATLADS Hubs are the perfect 65mm width fit for the larger 9 & 10 inch tyres to get maximum surface contact (GRIP) in the muddiest of conditions when contact is needed most!

Currently only available in Natural Black & White with Black Logos the PHATLADS Weigh just 226g per hub (not including the Marine Grade Stainless Steel hardware used to hold them together & fit them to the Pulleys) TRAMPA's PHATLADS are the lightest choice of hub for 9” & 10” Tyres.

There are two sets of Bolt holes running around the perimeter of the PHATLADS Hubs, these are Inner & Outer positions! The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the nut housings on the thinner of the 2 parts & once the 2 parts are mated together the Shorter M4x45mm bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. 

The Inner M4x50mm T20 TORX bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth Slave Pulley when fitted with 6 inch tyres, the 66 tooth Slave Pulley when fitted with 8 inch Tyres & 76 Tooth Slave Pulley when fitting 9 Inch tyres.... Having 2 sets of Bolt holes allows the user to be able to remove the wheel from the assembly without deflating & disassembling the wheel, meaning they can HOT-SWAP their wheel. Being able to 'Hot Swap' your wheels without taking them apart saves you lots of time when it comes to creating different rider setups, after all a board with 6 inch wheels is completely different to a board with 9 inch 

It is possible to fit both the 6001-2RS & 16001-2RS Bearings into the bearing housing of these hubs, of course Bearing reducer sleeves can be used to reduce the bearings from 12mm to either 9.525mm (TRAMPA's Mini Spring Trucks & 12FIFTIES Trucks use 9.525mm Axles) or 10mm axles if your axle should be 10mm not the imperial 9.525mm TRAMPA uses. 

Soon to be available soon in a selection of colour co-ordinating options, TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's  OPEN BELT DRIVE PRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups....

& 16001-2RS Bearings into the bearing housing of these hubs, of course Bearing reducer sleeves can be used to reduce the bearings from 12mm to either 9.525mm (TRAMPA's Mini Spring Trucks & 12FIFTIES Trucks use 9.525mm Axles) or 10mm axles if your axle should be 10mm not the imperial 9.525mm TRAMPA uses. 

Soon to be available soon in a selection of colour co-ordinating options, TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's  OPEN BELT DRIVE PRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups....

Black Plastic Anti Dust Valve Cap

Standard dust caps to fit all inner tubes. Keep the crud out of your valves!. There is nothing worse than not being able to inflate your tyres. So ensure your Anti dirt dust caps are fitted tight!. Also fits bi-cycle valves

9 Inch Re-enforced Inner Tube made by INNOVA - 225x65mm

INNOVA's Re-enforced 9 Inch inner tube measures 225mm x 65mm and will fit into all the of the 9 inch Tyres on the TRAMPA website. This 9 Inch Inner Tube will also fit into the tyres of other brands. Being made from slightly thicker rubber, this Inner Tube is slightly heavier than alternatives but the Inner Tube will handle much higher than recommended inflation rates... Therefore this INNOVA inner tube is ideal for heavier or pro riders seeking high inflation pressures...

This INNOVA Inner tube will fit into all known 9 inch tyres as well as most ATB Hubs on the market & it comes as expected with a "Plastic Anti Dust" Valve cap!

Punctures Suck! Its always possible to get a puncture in the environments we ride in, so always carry a spare if you don't want your day spoiling...

9 Inch TRAMPA Mud-Plugger Tyre

TRAMPA's new & incredibly aggressive 9 inch MUD-PLUGGER Tyre works best in the worst conditions!

Using a 3ply Hard compound rubber, the reinforced structure of the tyre will prevent the possibilities of punctures & with Grip on Grip & Grip on the side walls, and a 2.5 inch surface contact the 9 Inch Mud-Plugger Tyres will pretty much take you anywhere you can imagine riding! Lowering the tyre pressure will further increase your grip :-)

9 Inch Tyres will only fit to the amazing 9 Inch MEGASTAR Rims or the 3 Spoke PRIMO Hubs.

Using 9 inch MEGASTAR Rims, you can connect the 9 inch Mud-Plugger tyres to the Pro Belt Drive & the Pro Spur Gear Drive Electric Mountainboards

Using 3 Spoke Primo Hubs It is possible to connect with 9 inch Mud-Plugger Tyres to the Urban Electric Mountainboards

The 9 Inch Mud-Plugger tyres will provide you with loads of extra grip for an Electric Mountainboard, but to save money & most importantly weight you only need 2x Wheels to get all the extra grip, so we have made it is possible for you to purchase 2x 9 inch MEGASTAR Wheels with a complete Pro Electric Mountainboard at a very special upgrade price when purchased with a complete board....

 

TRAMPA's AMAZING 5 Spoke PHATLADS hubs are DEEP-DISH (Extra wide), OFF-SET & the latest addition to fit into TRAMPA’s amazing range of small off road wheels.

Injection molded using premium Dupont plastic composites, PHATLADS Hubs utilize a special 2 parts split-rim design that can fit any 6, 7, 8 & even 10” tyre that TRAMPA offers – One hub to fit them all will transform your ride experience for sure!

Measuring 65mm wide the PHATLADS hubs are a half inch wider than regular 8 inch TRAMPA hubs & are known as ‘DEEP DISH’ due to the Angle of the spokes on the fatter half part, allowing the wider Rim width to sit in the same axle space as a norrower hub, consequentially giving an 'offset bearing position'. Increasing the Rim width increases the ground contact of any tyres fitted to them giving a low wide look when the 6, 7 & 8 inch tyres are fitted & the PHATLADS Hubs are the perfect 65mm width fit for the larger 9 & 10 inch tyres to get maximum surface contact (GRIP) in the muddiest of conditions when contact is needed most!

Currently only available in Natural Black & White with Black Logos the PHATLADS Weigh just 226g per hub (not including the Marine Grade Stainless Steel hardware used to hold them together & fit them to the Pulleys) TRAMPA's PHATLADS are the lightest choice of hub for 9” & 10” Tyres.

There are two sets of Bolt holes running around the perimeter of the PHATLADS Hubs, these are Inner & Outer positions! The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the nut housings on the thinner of the 2 parts & once the 2 parts are mated together the Shorter M4x45mm bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. 

The Inner M4x50mm T20 TORX bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth Slave Pulley when fitted with 6 inch tyres, the 66 tooth Slave Pulley when fitted with 8 inch Tyres & 76 Tooth Slave Pulley when fitting 9 Inch tyres.... Having 2 sets of Bolt holes allows the user to be able to remove the wheel from the assembly without deflating & disassembling the wheel, meaning they can HOT-SWAP their wheel. Being able to 'Hot Swap' your wheels without taking them apart saves you lots of time when it comes to creating different rider setups, after all a board with 6 inch wheels is completely different to a board with 9 inch 

It is possible to fit both the

TRAMPA's AMAZING 5 Spoke PHATLADS hubs are DEEP-DISH (Extra wide), OFF-SET & the latest addition to fit into TRAMPA’s amazing range of small off road wheels.

Injection molded using premium Dupont plastic composites, PHATLADS Hubs utilize a special 2 parts split-rim design that can fit any 6, 7, 8 & even 10” tyre that TRAMPA offers – One hub to fit them all will transform your ride experience for sure!

Measuring 65mm wide the PHATLADS hubs are a half inch wider than regular 8 inch TRAMPA hubs & are known as ‘DEEP DISH’ due to the Angle of the spokes on the fatter half part, allowing the wider Rim width to sit in the same axle space as a norrower hub, consequentially giving an 'offset bearing position'. Increasing the Rim width increases the ground contact of any tyres fitted to them giving a low wide look when the 6, 7 & 8 inch tyres are fitted & the PHATLADS Hubs are the perfect 65mm width fit for the larger 9 & 10 inch tyres to get maximum surface contact (GRIP) in the muddiest of conditions when contact is needed most!

Currently only available in Natural Black & White with Black Logos the PHATLADS Weigh just 226g per hub (not including the Marine Grade Stainless Steel hardware used to hold them together & fit them to the Pulleys) TRAMPA's PHATLADS are the lightest choice of hub for 9” & 10” Tyres.

There are two sets of Bolt holes running around the perimeter of the PHATLADS Hubs, these are Inner & Outer positions! The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the nut housings on the thinner of the 2 parts & once the 2 parts are mated together the Shorter M4x45mm bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. 

The Inner M4x50mm T20 TORX bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth Slave Pulley when fitted with 6 inch tyres, the 66 tooth Slave Pulley when fitted with 8 inch Tyres & 76 Tooth Slave Pulley when fitting 9 Inch tyres.... Having 2 sets of Bolt holes allows the user to be able to remove the wheel from the assembly without deflating & disassembling the wheel, meaning they can HOT-SWAP their wheel. Being able to 'Hot Swap' your wheels without taking them apart saves you lots of time when it comes to creating different rider setups, after all a board with 6 inch wheels is completely different to a board with 9 inch 

It is possible to fit both the 6001-2RS & 16001-2RS Bearings into the bearing housing of these hubs, of course Bearing reducer sleeves can be used to reduce the bearings from 12mm to either 9.525mm (TRAMPA's Mini Spring Trucks & 12FIFTIES Trucks use 9.525mm Axles) or 10mm axles if your axle should be 10mm not the imperial 9.525mm TRAMPA uses. 

Soon to be available soon in a selection of colour co-ordinating options, TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's  OPEN BELT DRIVE PRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups....

& 16001-2RS Bearings into the bearing housing of these hubs, of course Bearing reducer sleeves can be used to reduce the bearings from 12mm to either 9.525mm (TRAMPA's Mini Spring Trucks & 12FIFTIES Trucks use 9.525mm Axles) or 10mm axles if your axle should be 10mm not the imperial 9.525mm TRAMPA uses. 

Soon to be available soon in a selection of colour co-ordinating options, TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's  OPEN BELT DRIVE PRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups....

Fits 76 Tooth Pulley for best gearing on Electric Boards - 

1x 9 Inch Mud-Plugger Tyre
1x 9 INCH Inner Tube - INNOVA
1x Black Plastic Anti Dust Valve Cap
Weight: 628g
What colour PHATLADS hubs do you want?
What colour PHATLADS hubs do you want?

Matt Black PHATLADS hubs please
Matt Black PHATLADS hubs please

Gloss White with Black Logo PHATLADS hubs please (+£5)
Gloss White with Black Logo PHATLADS hubs please (+£5)

Quantity required:
We have enough parts to make…  
RRP £35 - per wheel

Excluding VAT

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon