This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

BLACK PHATLADZ Deepdish hub with 9 Inch BLACK PRIMO Striker 9 Inch Tyres

PHATLADS 5 spoke hubs with BLACK 9 Inch Striker Tyres PRIMO STRIKER 9 Inch Tyre - BLACK 9 Inch Regular Inner Tube made by PRIMO - 225x65mm PHATLADS 5 spoke DEEP-DISH Hubs - Natural BLACK
RRP
£40
exc tax

How to put a wheel on an Infinity or Vertigo truck

How to put a wheel on an Ultimate Truck

M4 x 45mm Socket Capped TORX Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 45mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA PHATLADZ HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim, eventually screwing  into the M4 nut on the other side easly.

Weighing just 3 grams each, they are very lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

M4 x 50mm TORX Socket Capped Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA SUPERSTAR HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim of the SUPERSTAR HUB eventually screwing  into the M4 nut on the other side easly.

Weighing just 3 grams each, they are very lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

USED FOR: 
 
SUPERSTAR HUBS
MEGASTAR HUBS

Black Plastic Anti Dust Valve Cap

Standard dust caps to fit all inner tubes. Keep the crud out of your valves!. There is nothing worse than not being able to inflate your tyres. So ensure your Anti dirt dust caps are fitted tight!. Also fits bi-cycle valves

9 Inch Regular Inner Tube made by PRIMO - 225x65mm

PRIMO's own 9 Inch Inner Tube has dimensions of 225mm (outer diameter) x 65mm (width) & will fit into all known 9 Inch Tyres & ATB Hubs on the market!

The CST PRIMO Inner Tube incorporates slightly thicker rubber into its manufacture process which means the tube is slightly heavier than alternatives but does allow the rider to inflate slightly higher. This extra thickness also gives some extra resistance to punctures, but punctures suck, so always carry a spare inner tube when you are riding as you never know when you might get one.  

The PRIMO Tube uses a 90º Brass Inflation valve which will not rust on you & comes as you would expected with a plastic "anti dust" valve cap!

M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts

Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or  8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!

PHATLADS - 5 Spoke Hub Deep Dish Split Rim hub natural BLACK fits 6,7,8,9 & 10 Inch tyres!! Amazing

TRAMPA's 5 Spoke PHATLADS hubs are DEEP-DISH (Extra wide), OFF-SET & the latest addition to fit into TRAMPA’s amazing range of small off road wheels.

Injection molded using premium Dupont plastic composites, PHATLADS Hubs utilize a special 2 parts split-rim design that can fit any 6, 7, 8 & even 10” tyre that TRAMPA offers – One hub to fit them all will transform your ride experience for sure!

Measuring 65mm wide the PHATLADS hubs are a half inch wider than regular 8 inch TRAMPA hubs & are known as ‘DEEP DISH’ due to the Angle of the spokes on the fatter half part, allowing the wider Rim width to sit in the same axle space as a norrower hub, consequentially giving an 'offset bearing position'. Increasing the Rim width increases the ground contact of any tyres fitted to them giving a low wide look when the 6, 7 & 8 inch tyres are fitted & the PHATLADS Hubs are the perfect 65mm width fit for the larger 9 & 10 inch tyres to get maximum surface contact (GRIP) in the muddiest of conditions when contact is needed most!

Currently only available in Natural Black & White with Black Logos the PHATLADS Weigh just 226g per hub (not including the Marine Grade Stainless Steel hardware used to hold them together & fit them to the Pulleys) TRAMPA's PHATLADS are the lightest choice of hub for 9” & 10” Tyres.

There are two sets of Bolt holes running around the perimeter of the PHATLADS Hubs, these are Inner & Outer positions! The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the nut housings on the thinner of the 2 parts & once the 2 parts are mated together the Shorter M4x45mm bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. 

The Inner M4x50mm T20 TORX bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth Slave Pulley when fitted with 6 inch tyres, the 66 tooth Slave Pulley when fitted with 8 inch Tyres & 76 Tooth Slave Pulley when fitting 9 Inch tyres.... Having 2 sets of Bolt holes allows the user to be able to remove the wheel from the assembly without deflating & disassembling the wheel, meaning they can HOT-SWAP their wheel. Being able to 'Hot Swap' your wheels without taking them apart saves you lots of time when it comes to creating different rider setups, after all a board with 6 inch wheels is completely different to a board with 9 inch 

It is possible to fit both the 6001-2RS & 16001-2RS Bearings into the bearing housing of these hubs, of course Bearing reducer sleeves can be used to reduce the bearings from 12mm to either 9.525mm (TRAMPA's Mini Spring Trucks & 12FIFTIES Trucks use 9.525mm Axles) or 10mm axles if your axle should be 10mm not the imperial 9.525mm TRAMPA uses. 

Soon to be available soon in a selection of colour co-ordinating options, TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's  OPEN BELT DRIVEPRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups....

TRAMPA's 5 Spoke PHATLADS hubs are DEEP-DISH (Extra wide), OFF-SET & the latest addition to fit into TRAMPA’s amazing range of small off road wheels.

Injection molded using premium Dupont plastic composites, PHATLADS Hubs utilize a special 2 parts split-rim design that can fit any 6, 7, 8 & even 10” tyre that TRAMPA offers – One hub to fit them all will transform your ride experience for sure!

Measuring 65mm wide the PHATLADS hubs are a half inch wider than regular 8 inch TRAMPA hubs & are known as ‘DEEP DISH’ due to the Angle of the spokes on the fatter half part, allowing the wider Rim width to sit in the same axle space as a norrower hub, consequentially giving an 'offset bearing position'. Increasing the Rim width increases the ground contact of any tyres fitted to them giving a low wide look when the 6, 7 & 8 inch tyres are fitted & the PHATLADS Hubs are the perfect 65mm width fit for the larger 9 & 10 inch tyres to get maximum surface contact (GRIP) in the muddiest of conditions when contact is needed most!

Currently only available in Natural Black & White with Black Logos the PHATLADS Weigh just 226g per hub (not including the Marine Grade Stainless Steel hardware used to hold them together & fit them to the Pulleys) TRAMPA's PHATLADS are the lightest choice of hub for 9” & 10” Tyres.

There are two sets of Bolt holes running around the perimeter of the PHATLADS Hubs, these are Inner & Outer positions! The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the nut housings on the thinner of the 2 parts & once the 2 parts are mated together the Shorter M4x45mm bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. 

The Inner M4x50mm T20 TORX bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth Slave Pulley when fitted with 6 inch tyres, the 66 tooth Slave Pulley when fitted with 8 inch Tyres & 76 Tooth Slave Pulley when fitting 9 Inch tyres.... Having 2 sets of Bolt holes allows the user to be able to remove the wheel from the assembly without deflating & disassembling the wheel, meaning they can HOT-SWAP their wheel. Being able to 'Hot Swap' your wheels without taking them apart saves you lots of time when it comes to creating different rider setups, after all a board with 6 inch wheels is completely different to a board with 9 inch 

It is possible to fit both the 6001-2RS & 16001-2RS Bearings into the bearing housing of these hubs, of course Bearing reducer sleeves can be used to reduce the bearings from 12mm to either 9.525mm (TRAMPA's Mini Spring Trucks & 12FIFTIES Trucks use 9.525mm Axles) or 10mm axles if your axle should be 10mm not the imperial 9.525mm TRAMPA uses. 

Soon to be available soon in a selection of colour co-ordinating options, TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's  OPEN BELT DRIVEPRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups....

PLEASE BE AWARE, THIS IS A PHATLADS PART & WHEN PURCHASED DOES NOT INCLUDE NUTS OR BOLTS. 

PRIMO STRIKER 9 Inch Tyre - BLACK

PRIMO's 9 Inch STRIKER Tyre design brief is styled towards fast riding on hard packed dirt surfaces. It is made using a hard rubber compound with a wide Center Bead to help achieve & maintain maximum rolling speeds, whilst the close cut grip pattern around the sides of the tyre gives loads of grip on all kinds of changeable terrain's. Using Harder Rubber makes the STRIKER Tyre very fast whilst still hard-wearing, The PRIMO STRIKER is a great Tyre option for riding on any Solid surfaces from dusty dirt tracks to hard packed asphalt. 

Incorporated into the Rims of the tyre are 4 Inch wide Steel Bands. As the Rims are 4 Inch's wide this means that the 9 Inch PRIMO STRIKER tyre is too big to fit onto the regular TRAMPA hubs & therefore the 9 Inch Striker tyres will currently only fit onto the PRIMO 3-Spoke Composite Hubs. Larger wheels will travel better over bumpier or softer ground making them great for kiteboarding down the beach if the sand is soft. When the tyres are inflated to they measure 225mm in Diamter & 65mm wide.

Regular sized Threads (TPI) tie the 4 Inch Steel bands together giving the 9 Inch PRIMO STRIKER tyre the strength & structure to be inflated up to the recommended factory inflation pressures. The more you inflate your Tyres the faster you will roll! If you over inflate the Tyres it is possible they will explode which may cause you serious injury! The official maximum inflation pressure set by the factory for the 9 inch STRIKER Tyre is 50psi,  If you do decide to go beyond the max inflation pressure ensure your nuts & bolts are tight before inflating & deflate back to a regular pressure after use. 

Using TRAMPA's NEW & AMAZING 9 inch Deep-Dish MEGASTAR wheels, it is now possible to comfortably fit larger sized 9 inch wheels into the assembly any of the TRAMPA Belt Drives or Spur Gear Drives using 16 inch Mountain board Spring Trucks. 

Using 9 inch wheels which have been CNC Precision Milled from two solid blocks, milled with an offset bearing position, will significantly widen your wheel base making the board feel more stable & planted, whilst the additional width of the tires (9 inch Mud-Pluggers are 2.5 Inches wide where as 8 inch tyres are just 2 inches wide) increases the surface contact with the ground & as you can tell from the name of the Tyre which pretty much describes what its capable of, the extra 1/2 inch of tyre & the aggressive directional grip results in absolute heaps of extra grip comparing to the smaller 8 inch tyres, especially when riding off road in mddy conditions.

The increased tyre profile size of the well gripped sidewall will not only give you more Grip but also loads of extra Comfort when rolling over rough stuff & the increase of overall wheel size going from 8 inch to 9 inch will give you a natural Geared increase in Top Speed by approx 5%, making the new MEGASTAR hubs a must have piece of equipment for all serious of road electric mountain board riders out there...

It is possible to fit the 9 inch MEGASTAR WHEELS to any of TRAMPA's 66 Tooth Belt Driven Slave Pullies or 58/59 Tooth Spur Gear Drive Pulleys that would usually fit to the 8 inch Superstar wheels, So if you're looking for the latest all round upgrade, then this is the one for you!

The downside to using 9 inch wheels is the increase in weight... with all the increase in size they are bound to weigh more than the smaller wheels & rubber can weigh a lot... so to gain the extra grip that we talk about without adding to much extra weight we suggest that you only need to fit 2x of the 9 inch wheels on the rear drive wheels giving you the grip without all the weight of 4x wheels, so you only need just 2x 9 inch wheels to gain the extra Grip, speed & Comfort without too much extra weight...  You might be thinking, what 8 inch on the front and 9 inch on the back.... yep thats right guys.... You might be thinking but then its higher one end than the other, Yep, thats right.... the extra height at the rear almost forces you int a more aggressive stance, positioning you ready to take the huge forces in the acceleration... the stance is nice, the tyres are amazing.....!!!

Fits 76 Tooth Pulley for best gearing on Electric Boards - 

1x 9 Inch PRIMO STRIKER Tyre - BLACK
1x 9 Inch Inner Tube - PRIMO
1x Black Plastic Anti Dust Valve Cap
1x 1x PHATLADS Split Rim OFF-SET Deep-Dish 5 Spoke Hubs
5x 5x PHATLADS Stainless Steel Outer Bolt M4x45mm
5x 5x PHATLADS Stainless Steel Inner Bolt M4x50mm
5x 5x M4 Stainless Steel Nylock Nut
Weight: 770g
What colour PHATLADS hubs do you want?
What colour PHATLADS hubs do you want?

Matt Black PHATLADS hubs please
Matt Black PHATLADS hubs please

Gloss White with Black Logo PHATLADS hubs please (+£5)
Gloss White with Black Logo PHATLADS hubs please (+£5)

Quantity required:
We have enough parts to make…  
RRP £40 - per wheel

Excluding VAT

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon