This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

FULL CNC SAVAGE ATB TRUCK from solid Billet ALLOY, fitted with solid CRMO STEEL Axles & Kingpin

FULL CNC SAVAGE ATB TRUCK from solid Billet ALLOY, fitted with solid CRMO STEEL Axles & Kingpin SAVAGE ATB Hanger with 18.2mm Spacers & Axle nuts CUSTOM Spring Truck Baseplate - Extruded T6 Aluminum Anodised & CNC precision Milled CUSTOM Spring Truck Baseplate - Extruded T6 Aluminum Anodised & CNC precision Milled CUSTOM Spring Truck Baseplate - Extruded T6 Aluminum Anodised & CNC precision Milled 8mm Heat Treated STEEL Kingpin kit for TRAMPA Spring Trucks x 1 Complete Spring or Barrel kit for 1x Truck
RRP
£150+

STOCK ARRIVES 20th March 2022!!

Designed for those customers who insist on installing the very best, the strongest & highest performing equipment, well here now is TRAMPA's new 16.5 inch wide SAVAGE hanger, the best we have made yet!

Visibly the SAVAGE Hanger looks very much the same as the regular ATB Spring Hanger, to fit to the Baseplate & connect with the springs & Barrels that need to be fitted it has to be similar, so the differences or improvements you could say are subtle, for instance instead of being produced from forged alloy the SAVAGE Hanger is produced from a solid billet a premium alloy & entirely CNC to shape, but you could not tell on the surface.

The SAVAGE Hanger is also considerably beefed beefed up in all the critical areas compared to the original forged alloy spring truck. With CNC cut outs & trims in all the non-critical or most importantly structural areas, increased strength over the original has been achieved whilst to save weight excess material has been removed as much as possible. In the same breath the base of the hanger has been given an extra couple of millimeters of thickness giving huge extra structural strength & finally the SAVAGE Hanger has been Seriously Re-enforced around the kingpin area & installed with super strong SOLID 12mm CROM-MOLY Steel AXLES! 

The SAVAGE hanger measures 16.5" wide, which is half inch wider than the originals making this Hanger the obvious choice for the largest or hardest of riders out there!
In the accessories pages

M5 x 12mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-Ratchet Bindings

-Camlock Bindings

-Heelstraps

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

7/16ths Nut - Marine Grade Stainless steel Nylock Axle HALF nut (W7/16-20T UNF) - Fits to 12mm Axles

This very special 7/16ths of an inch Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut.. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore further reducing weight in the Truck! A few Grams here & a few grams there soon adds up & makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area, where a few grams makes all the difference...

This very special 3/8ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W7/16 - 20T - UNF. This Nut is used to hold the wheels onto the axles of the Spring Trucks fitted with 12mm axles. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 16mm or 5/8thths of an Inch spanner to tighten / loosen the Nut onto the Axle or Kingpin. Do not overtighten the nut & make sure the wheel can spin freely but does not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

Wheel support spacer for all TRAMPA Wheels on 12mm ATB Axles - CNC precision 12mm x 16mm x 18.2mm

This special Spacer measures 12mm (id) x 16mm (od) x 18.2mm (long) & has 2 uses!. It is firstly known as the Bearing Support Spacer as this Spacer fits between the Bearings of a 6 Spoked HYPA Hub, (when mounting the HYPA wheel onto 12mm Axles) & secondly it is also known as the AXLE SUPPORT SPACER as this spacer is also used to position any of the TRAMPA wheels in the perfect position onto the axles of 12mm TRAMPA Spring trucks....

TRAMPA spacers are produced as one long tube. The Tube is Heat Treated to gain extra strength & is then Bead Polished to give the metal extra surface protection & a shiny best appearance. The tube is then cut to the exact length for precision mounting. 

CUSTOM Spring Truck Baseplate - Extruded T6 Aluminum Anodised & CNC precision Milled

The  INFINITY Baseplate will fit to all of the TRAMPA Spring Truck Hangers but is designed specifically to work in conjunction with the Mini Spring Hanger as it houses a NEW Dual Spring Adjuster position! When the Springs are moved to the new inside position, the new location allows the rider to turn the board very very easily, making it perfect for fast carve riding on all kinds of terrain. You can see the new & growing TRAMPA STREET CARVER range of products here...

The  INFINITY Baseplate is, as its name suggests, designed & built to last forever! Aircraft grade 6061 Aluminum is forced through a Die to create our re-enforced extruded profile. Extruding Aluminum ensures consistent high quality strength. Once Extruded the Baseplate is T6 Heat Treated. Heat treating extruded aluminum fuses the molecules even closer together making it as strong as possible, enabling the INFINITY Baseplate to easily cope with the extreme stresses of all types of off road boarding.

Once Heat Treated, the profile has its fixing holes punched into position & then its Bead Polished in preparation to be Anodised Silver. Once the colour has dried, the Baseplate is then returned to the factory for the precision CNC Machine to accurately mill the Kingpin holes, giving the exact precision required for constructing the Truck.

17 inch wide FULL CNC SAVAGE Motor Mount Hanger with heat treated 12mm Chrom Molly Steel Axles - connects with all Spring Truck Baseplates & Mountainboard Motor Mounts

STOCK ARRIVES 20th March 2022!!


Designed for those insisting on fitting only the very best there is, TRAMPA's new SAVAGE HANGER is one solid piece of CNC lushness.

The SAVAGE HANGER a slightly wider but considerably beefed-up / cross version of the original Infinity / Vertigo / Ultimate Spring Truck hangers which already have so much reputation to boast about!

Re-enforced around the kingpin & factory installed with SOLID 12mm CR-MO Steel AXLES, the SAVAGE hanger measures 16.5" wide, which is half inch wider than the originals...

The SAVAGE Hanger will fit with all of TRAMPA's SPRING TRUCK BASEPLATES & all SPRING TRUCK MOTOR MOUNTS.


In the accessories pages

STEEL Kingpin M6x 8mm x 80mm for Spring Truck - Heavy Duty 12.9 Steel

This M8 x 80mm STAINLESS STEEL Spring Truck Kingpin is used to connect the Hanger & the Baseplate on the TRAMPA INFINITY, VERTIGO or ULTIMATE Trucks. By using an 8mm Kingpin we have managed to save loads of weight whilst retaining all the strength necessary for the job by using high quality metals true to our word!

This M8 x 80mm Kingpin connects through the truck & into an M6 Nut. You'll need a 4mm Allen key to hold the Kingpin & a 10mm spanner to tighten/loosen your M6 Kingpin Nut.

This Kingpin pushes through Plastic Bushings before being placed into position in the Truck System. The Plastic bushings allow the metal parts (Hanger & Baseplate) to move inside each other without allowing the metal parts to touch or wear out. The Plastic Bushings will wear out over time & will eventually perish & need replacing. SO, make sure your Bushings are always in good working order after riding riding or especially when upgrading your Kingpin, it might be time to replace them too due to the unavoidable wear & tear of moving mountainboard parts.

This Kingpin lives up to TRAMPA's incredibly high quality standards, but it's always handy to have a spare just in case you do break one out on a ride.... Upgrade ur Kingpin by fitting the TRAMPA TITANIUM Kingpin which will save you loads of weight & fit into all of the TRAMPA Spring Trucks!

King Pin bushings 2mm Base for Spring Trucks

The precision made Kingpin Bushings locate the Kingpin in a wear-free position between the hanger & Baseplate

The Kingpin bushings are a small item & are subjected to a lot of forces and through normal/regular use they will ultimately need replacing over time. Depending on what surface you are riding on will depend on how long these bushings will last you. So to make sure your trucks are always performing at their best inspect these Bushings regularly (preferably before riding) & in particular replace any that are showing signs of wear & from time to time replace them anyway...

The difference between the four bushings is the thickness of the base. The different base sizes are 1mm, 1.5mm, 2mm and 2.5mm. 2.5mm is the standard size we work to. As all trucks have 4 bushings this .5mm difference in each of the bushing bases allows us to bridge a maximum distance of 2mm (4x.05mm=2m) resolving any foreseeable problems.

Kingpin Bushings 2.5mm Base - for Spring Trucks

The precision made Kingpin Bushings locate the Kingpin in a wear-free position between the hanger & Baseplate

The Kingpin bushings are a small item & are subjected to a lot of forces and through normal/regular use they will ultimately need replacing over time. Depending on what surface you are riding on will depend on how long these bushings will last you. So to make sure your trucks are always performing at their best inspect these Bushings regularly (preferably before riding) & in particular replace any that are showing signs of wear & from time to time replace them anyway...

The difference between the four bushings is the thickness of the base. The different base sizes are 1mm, 1.5mm, 2mm and 2.5mm. 2.5mm is the standard size we work to. As all trucks have 4 bushings this .5mm difference in each of the bushing bases allows us to bridge a maximum distance of 2mm (4x.05mm=2m) resolving any foreseeable problems.

Kingpin Bushings 3mm Base - for Spring Trucks

The precision made Kingpin Bushings locate the Kingpin in a wear-free position between the hanger & Baseplate.  The Kingpin bushings are a small item & are subjected to a lot of forces and through normal/regular use they will ultimately need replacing over time. Depending on what surface you are riding on will depend on how long these bushings will last you. So to make sure your trucks are always performing at their best inspect these Bushings regularly (preferably before riding) & in particular replace any that are showing signs of wear & from time to time replace them anyway... The difference between the four bushings is the thickness of the base. The different base sizes are 1mm, 1.5mm, 2mm and 2.5mm. 2.5mm is the standard size we work to. As all trucks have 4 bushings this .5mm difference in each of the bushing bases allows us to bridge a maximum distance of 2mm (4x.05mm=2m) resolving any foreseeable problems.

Custom Colour Spring - Powdercoated Sprung Steel Steering Springs

TRAMPA's SPRINGS are coiled to precision & fit into the TRAMPA Spring Trucks perfectly. They easily squeeze into the space between the Baseplate & Hanger & being made to measure they are firstly very easy to fit with no clamps or tools required to squueze them into position & secondly to be super responsive to the rider.!  Once the spring assembly is fitted correctly the steering resistance is taken up instantly!

Our Springs have been designed to work in perfect harmony with the TRAMPA DAMPA's & TRAMPA SPRING RETAINER providing maximum performance from the "Spring assembly" to the rider. The DAMPA's drop into the SPRING & the SPRING RETAINERS seal the ends of the spring, holding the DAMPA in exact position to be pre-loaded & squeezed into the truck. Using just a little bit of muscle, squeeze the loaded spring into the truck, then lock the spring into position using the Spring Adjuster & M5 x 12mm Countersunk Bolt. The TRAMPA spring Truck steering system is highly responsive & totally customisable by interchanging the DAMPA's to harder Urethane. Other Mountain Board brands springs will not fit the TRAMPA Trucks as they are a different in dimension.

TRAMPA Springs are available in a selection of Powder-coated colours for good looks & of course for best surface coating protection & this one comes to you in Powder Coated Black. 

Spring Retainer - Specially designed to work in harmony with the Dampa & spring

TRAMPA's very own & very special re-enforced Spring retainer. Specifically shaped to fit tightly inside the TRAMPA springs & snugly hold the Trampa Dampa in the exact position to give precision steering to the rider. Made by Injection Moulding using original Dupont Materials, with an extra wide Marine-Grade Stainless Steel Flanged Insert seated internally, re-enforcing the Retainer. The Extra Strength of the re-enforced flange, eliminates the need for a very fiddly fitting washer, that is still found in the MBS and Scrub boards today.

Designed to work in harmony with the TRAMPA spring and TRAMPA Dampa to help create immediate resistance from your steering system. With TRAMPA Embossed around the rim of the retainer - you'll have performance with pimpness!

Custom TRAMPA DAMPA

TRAMPA's SPRINGS are coiled to precision & fit into the TRAMPA Spring Trucks perfectly. They easily squeeze into the space between the Baseplate & Hanger & being made to measure they are firstly very easy to fit with no clamps or tools required to squeeze them into position & secondly to be super responsive to the rider.!  Once the spring assembly is fitted correctly the steering resistance is taken up instantly!

Our Springs have been designed to work in perfect harmony with the TRAMPA DAMPA's & TRAMPA SPRING RETAINER providing maximum performance from the "Spring assembly" to the rider. The DAMPA's drop into the SPRING & the SPRING RETAINERS seal the ends of the spring, holding the DAMPA in exact position to be pre-loaded & squeezed into the truck. Using just a little bit of muscle, squeeze the loaded spring into the truck, then lock the spring into position using the Spring Adjuster & M5 x 12mm Countersunk Bolt. The TRAMPA spring Truck steering system is highly responsive & totally customisable by interchanging the DAMPA's to harder Urethane. Other Mountain Board brands springs will not fit the TRAMPA Trucks as they are a different in dimension.

TRAMPA Springs are available in a selection of Powder-coated colours for good looks & of course for best surface coating protection & this one comes to you in Powder Coated Black. 

Spring length - 66.5mm
Spring external diameter - 30mm
Spring internal diameter - 21mm
Spring thickness - 4.2mm
Black Powder coated steel Spring.
Weight: 64g

The TRAMPA DAMPA is a Urethane Elastomer that fits inside the Spring of a Truck. Its purpose is to support the Spring & give extra resistance during steering. Its clever design has three balls stacked & connected on-top of each other. The middle ball is slightly fatter than the outer two, during steering they all compress against each other giving greater feed back in your turns. This stacked design gives a fantastic progressive feel to steering.

By varying the SHORE DUROMETER (Rubber Hardness) strength of the Urethane mixture, we can control the amount of movement in the DAMPA. This in turn allows the rider to custom tune the resistance of their steering perfect to their requirements. The spheres of the DAMPA fit perfectly into the cup of the specially made TRAMPA SPRING RETAINER which is the part that locates & locks the Spring in the the TRAMPA SPRING TRUCKSand they instantly start to work with the slightest movement from the rider. TRAMPA DAMPA's work in harmony with the rider, supplying the perfect amount of steering resistance whilst eliminating all chances of speed wobble. Now available in 5 different steering resistance's for all levels of rider out there, Orange DAMPA's are for easy steering, whilst White DAMPA's are for the totally committed! 

Turning the Spring Adjuster clockwise pre-loads the tension in the Spring and DAMPA. This can be adjusted on the fly to suit the terrain & conditions. Turning the spring adjuster too much will put pressure on the DAMPA & eventually it may split. Rather than putting too much pressure into the DAMPA, consider up-grading the DAMPA to a harder Shore Durometer as this will most likely increase your performance than over tightening a DAMPA that's not stiff enough for you. Please use the table below for guide.

 

COLOUR

Stiffness

Shore

Suitability Guide

ORANGE

Super Soft

55

Light Riders / Crazy Carvers!

PINK

Soft

60

Beginner Carvers

YELLOW

Average

65

Beginner / Intermediate

GREEN

Average (75kg+)

75

Intermediate / Adult sized rider

RED

Firm

80

Advancing rider / Teenage Freestyler

BLUE

Stiff

85

Fast & Advanced Freestyle Rider

WHITE

Stiffest

90

For the Insane only!

Spring Adjuster - Marine Grade Stainless Steel

TRAMPA's very own & very special SPRING ADJUSTER is made using A4 MARINE GRADE STAINLESS STEEL & is guaranteed never to rust on you! The Spring adjuster is fitted to the trucks once the springs have been pushed into position. The spring adjuster pre-tensions the steering suitable for the rider’s requirements. We designed the Spring Adjuster to be slightly shorter in length than other brands’, to avoid  the tip of the adjuster poking through the internal of the Spring Retainer, and interfering with the performance of the DAMPA located on the inside of the Retainer.

Should you need extra resistance from your steering because you wish to ride fast, or if you need more steering because the course is twisty, then you can very easily & quickly adjust the resistance of your steering by simply turning the spring adjuster in the correct direction. To get the most out of your trucks on changeable terrain, simply use a 4mm Allen Key to make your adjustments. Winding the Spring Adjuster clockwise increases the steering resistance, which in turn restricts wobble at high speed. Turning the Adjuster anti-clockwise loosens the steering allowing a more carvey ride.  

DO NOT over tighten your Spring Adjuster, as this may crush your DAMPA. If you need more steering resistance upgrade your DAMPA's & do not over tighten!

STOCK ARRIVES 20th March 2022!!

Designed for those customers who insist on installing the very best, the strongest & highest performing equipment, well here now is TRAMPA's new 16.5 inch wide SAVAGE hanger, the best we have made yet!

Visibly the SAVAGE Hanger looks very much the same as the regular ATB Spring Hanger, to fit to the Baseplate & connect with the springs & Barrels that need to be fitted it has to be similar, so the differences or improvements you could say are subtle, for instance instead of being produced from forged alloy the SAVAGE Hanger is produced from a solid billet a premium alloy & entirely CNC to shape, but you could not tell on the surface.

The SAVAGE Hanger is also considerably beefed beefed up in all the critical areas compared to the original forged alloy spring truck. With CNC cut outs & trims in all the non-critical or most importantly structural areas, increased strength over the original has been achieved whilst to save weight excess material has been removed as much as possible. In the same breath the base of the hanger has been given an extra couple of millimeters of thickness giving huge extra structural strength & finally the SAVAGE Hanger has been Seriously Re-enforced around the kingpin area & installed with super strong SOLID 12mm CROM-MOLY Steel AXLES! 

The SAVAGE hanger measures 16.5" wide, which is half inch wider than the originals making this Hanger the obvious choice for the largest or hardest of riders out there!
In the accessories pages

 

 

Fits to - Fits to 35º TRAMPA Mountainboard Decks
1x SAVAGE Motor Mount HANGER Full CNC with 12mm Cr-Mo Axles
2x 12mm ATB Axle 10.9 Grade Steel for SAVAGE Hangers
2x 12 x 18.2mm Wheel Support Spacer fits TRAMPA Wheels on 12mm Axles
2x 7/16ths (12mm) Marine Grade Stainless steel Nylock Axle HALF nut
1x CUSTOM Spring Truck Baseplate
1x STEEL Kingpin M6x 8mm x 80mm for Spring Truck - Heavy Duty 12.9 Steel
2x King Pin bushings 2mm Base for Spring Trucks
2x Kingpin Bushings 2.5mm Base - for Spring Trucks
2x Kingpin Bushings 3mm Base - for Spring Trucks
1x M8 x 1.5mm Form B Kingpin Washer Marine Grade Stainless steel
1x M6 Washer Form C - Marine Grade Stainless Steel
1x M6 Nut - Marine Grade Stainless steel Nylock nut
2x Custom Colour Spring
4x Trampa Spring Retainer - No Awkward Washers to fit
2x Custom TRAMPA DAMPA
2x Spring Adjuster - Marine Grade Stainless Steel
2x M5 x 12 Countersunk Allen-Key Stainless Steel Bolt
Weight: 868g
What colour Baseplate do you require...?
What colour Baseplate do you require...?

BLACK Anodised with SILVER logo VERTIGO Baseplate
BLACK Anodised with SILVER logo VERTIGO Baseplate

BLUE Anodised with BLACK logo VERTIGO Baseplate
BLUE Anodised with BLACK logo VERTIGO Baseplate

BRONZE Anodised with BLACK logo VERTIGO Baseplate
BRONZE Anodised with BLACK logo VERTIGO Baseplate

GOLD Anodised with BLACK logo VERTIGO Baseplate
GOLD Anodised with BLACK logo VERTIGO Baseplate

GREEN Anodised with BLACK logo VERTIGO Baseplate
GREEN Anodised with BLACK logo VERTIGO Baseplate

GUNMETAL Anodised with BLACK logo VERTIGO Baseplate
GUNMETAL Anodised with BLACK logo VERTIGO Baseplate

NAVY Powdercoated with BLACK logo VERTIGO Baseplate
NAVY Powdercoated with BLACK logo VERTIGO Baseplate

PINK Anodised with BLACK logo VERTIGO Baseplate
PINK Anodised with BLACK logo VERTIGO Baseplate

PURPLE Anodised with BLACK logo VERTIGO Baseplate
PURPLE Anodised with BLACK logo VERTIGO Baseplate

RED Anodised with BLACK logo VERTIGO Baseplate
RED Anodised with BLACK logo VERTIGO Baseplate

RED Powdercoated with BLACK logo VERTIGO Baseplate
RED Powdercoated with BLACK logo VERTIGO Baseplate

SILVER Anodised with BLACK logo INFINITY Baseplate
SILVER Anodised with BLACK logo INFINITY Baseplate

SILVER Anodised with BLACK logo VERTIGO Baseplate
SILVER Anodised with BLACK logo VERTIGO Baseplate

WHITE Powdercoated with BLACK logo VERTIGO Baseplate
WHITE Powdercoated with BLACK logo VERTIGO Baseplate

WHITE Powdercoated with BLUE logo VERTIGO Baseplate
WHITE Powdercoated with BLUE logo VERTIGO Baseplate

WHITE Powdercoated with RED logo VERTIGO Baseplate
WHITE Powdercoated with RED logo VERTIGO Baseplate

What colour Spring do you want or Would you like to fit Barrels?
What colour Spring do you want or Would you like to fit Barrels?

Please fit TRAMPA BARRELS Instead of Springs & Dampa's (+£10)
Please fit TRAMPA BARRELS Instead of Springs & Dampa's (+£10)

Nickel Plated Springs - SILVER
Nickel Plated Springs - SILVER

Powder Coated Springs - BLUE
Powder Coated  Springs - BLUE

Powder Coated Springs - BLACK
Powder Coated Springs - BLACK

Powder Coated Springs - GREEN
Powder Coated Springs - GREEN

Powder Coated Springs - PINK
Powder Coated Springs - PINK

Powder Coated Springs - PURPLE
Powder Coated Springs - PURPLE

Powder Coated Springs - RED
Powder Coated Springs - RED

Powder Coated Springs - WHITE
Powder Coated Springs - WHITE

Powder Coated Springs - YELLOW
Powder Coated Springs - YELLOW

What Colour 18.2mm Wheel Support Axle Spacers do you want?
What Colour 18.2mm Wheel Support Axle Spacers do you want?

BLACK 18.2mm Wheel Support Axle Spacers
BLACK 18.2mm Wheel Support Axle Spacers

BLUE 18.2mm Wheel Support Axle Spacers
BLUE 18.2mm Wheel Support Axle Spacers

BRONZE 18.2mm Wheel Support Axle Spacers
BRONZE 18.2mm Wheel Support Axle Spacers

GOLD 18.2mm Wheel Support Axle Spacers
GOLD 18.2mm Wheel Support Axle Spacers

GREEN 18.2mm Wheel Support Axle Spacers
GREEN 18.2mm Wheel Support Axle Spacers

GUNMETAL 18.2mm Wheel Support Axle Spacers
GUNMETAL 18.2mm Wheel Support Axle Spacers

PINK 18.2mm Wheel Support Axle Spacers
PINK 18.2mm Wheel Support Axle Spacers

PURPLE 18.2mm Wheel Support Axle Spacers
PURPLE 18.2mm Wheel Support Axle Spacers

RED 18.2mm Wheel Support Axle Spacers
RED 18.2mm Wheel Support Axle Spacers

SILVER 18.2mm Wheel Support Axle Spacers
SILVER 18.2mm Wheel Support Axle Spacers

What length Bolts do you require to fit your trucks
What length Bolts do you require to fit your trucks

M5x25mm Truck Bolt kit - 12-16ply Decks

M5x30mm Truck Bolt kit - 17-18ply Decks
M5x30mm Truck Bolt kit - 17-18ply Decks

Would you like to add some BullBars to your Mountainboard?
Would you like to add some BullBars to your Mountainboard?

Please add & fit 1x set of Carveboard BullBars (+£40)
Please add & fit 1x set of Carveboard BullBars (+£40)

Please add & fit 1x set of Mountainboard BullBars (+£50)
Please add & fit 1x set of Mountainboard BullBars (+£50)

No BullBars Thanks

Quantity required:
We have enough parts to make…  
RRP £150 - 1x TRUCK

Excluding VAT

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon