This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

76T Open Belt Drive Motor Mount & Motor Adaptor - SINGLE GUNMETAL

76T Open Belt Drive Motor Mount & Motor Adaptor - SINGLE GUNMETAL OBD Motor Mount Connector Panel for 76 tooth Pulleys - REGULAR or GOOFY M6 x 25mm Socket Capped Bolt for OBD Mounts & Scooter Clamps Open Belt Drive Motor Adaptor with Housed Bearing Connects with Both the 66 & the 76 Tooth Motor Mounts M4 x 10mm TORX Dome/Button Headed Head Bolt DIN6912 Marine Grade Stainless Steel TORX M4 x 20mm Socket Capped Head TORX Bolt ISO 4762 Marine Grade Stainless Steel OPEN BELT DRIVE Belt Tensioning System for 20mm Belts - Roller Housing
RRP
£55
exc tax

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

M6 x 25mm Bolt - Fixes Trucks to HolyPro Decks - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

You’ll need 8 of the TRAMPA M6 x 25mm Marine Grade Stainless Steel Bolts & 8 of the TRAMPA M6 Stainless Steel Nylock Nuts to attach a pair of TRAMPA Skate Trucks to any TRAMPA Deck with Risers. You’ll also need a pair of 10mm ring spanners to tighten and loosen the Nuts & Bolts. Don’t forget to make sure you’re Nuts & Bolts are tight before you ride!

M6 x 25mm Socket Capped Bolt for OBD Mounts & Scooter Clamps

TRAMPA's M6 x 30mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the PRIMO 3 Spoke Hubs. The socket capped head of the Bolt screws neatly though the HUB eventually screwing into the Marine Grade Stainless Steel M6 Nylock Nut on the other side of the hub. 

Weighing just 8 grams each, these Bolts are lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers nuts & bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You’ll will need a 5mm Allen Key  to tighten & loosen the Bolt from the nut. Ensure all your Nuts & Bolts are tight before riding!

M4 x 20mm Socket Capped Head TORX Bolt ISO 4762 Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt DIN6912 Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

Belt Tension Roller Housing for 20mm Belts

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

Made from T6 Heat-treated Aluminium, these Belt Tension Rollers are to designed to house a premium TRAMPA 608 BEARING, ensuring a smooth and consistent roll while tensioning the belts. Used with 20mm belts on OPEN BELT DRIVE Motor Mounts.

 

 

Sprung Steel E-CLIP used inside the Belt tension housings to secure 608 bearing

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

These C-Clips ensure the 608 bearing is secure within the Tension Rollers

 

Step SPACER used for positioning the 20mm Tension Roller on OBD Drive

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

These Spacer-Axles have two functions, correctly positioning the 20mm Tension Roller, as well as providing the housed 608 bearing a snug-fitting axle to spin freely on.

OBD Motor Mount Connector Panel for 76 tooth Pulleys - REGULAR or GOOFY

OBD Motor Mount Connector Panels are an all-in-one Mounting Panel & Truck connector, CNC’d from premium heat-treated T6 aluminium. Motor Mount Connector Panels are available in two models (66T or 76T), each designed with different gear ratios (therefore different performances) in mind.  

OBD 76T uses the 76 tooth Slave Pulley with a gear ratio of 5.43:1 - giving an amazing level of torque (similar to the Spur Gear Drive), and performance favouring insane acceleration over overall top speed. Due to clearance, OBD 76T Systems can only use 9 inch Wheels.

Attaches to the Motor Adaptor using 4x M4x10 Dome Headed Bolts & 1x M4x20 Socket Capped Bolt
Attaches to the Truck using 1x M6x25 Socket Capped Bolt.

Open Belt Drive Motor Adaptor with Housed Bearing Connects with Both the 66 & the 76 Tooth Motor Mounts

The Open Belt Drive Motor Adaptor has been precision CNC’d from heat-treated T6 Aluminium to fit securely to the 66T or 76T OBD Motor Mount Connector Panels. 

Able to fit any TRAMPA motor in the range, the OBD Motor Adaptor can also fit the amazing looking PRO DELRIN Motor covers. 

Attaches to the Motor Mount Connector Panels using 4x M4x10 Dome Headed Bolts & 1x M4x20 Socket Capped Bolt
Attaches to Motors using 4x M4x10 Dome Headed Bolts. 
Attaches to DELRIN Motor Covers using 5x 3.5x12 Plastic Thread Cutting Bolts

The following are required to build this product:

 

This simple motor mounting kit is as versatile as they come - able to work with most Mountainboard Trucks and wheels - as well as a huge variety of motor & pulley sizes.

Essentially, this kit is the barebones of your motor system - giving you the freedom to pick, choose, and customise what your final product will be!

In this kit you get the following items -
1x OBD Motor Mount Connector Panel for 76 tooth Pulleys - REGULAR or GOOFY
1x M6 x 25mm Socket Capped Bolt - Marine Grade Stainless steel
1x OBD Motor Adaptor with Housed Bearing
1x TRAMPA abec 7 608 or Si4n5 Ceramic Longboard & Skateboard Bearings
4x M4x10mm Dome Headed TORX Bolt - Marine Grade Stainless Steel
1x M4 x 20mm Socket Capped TORX Bolt - Marine Grade Stainless Steel
1x 20mm Stainless Steel Tension Roller Housing for 20mm Belts
1x TRAMPA abec 7 608 or Si4n5 Ceramic Longboard & Skateboard Bearings
1x Sprung Steel E-CLIP for Belt tension roller secures 608 bearing in position.
1x Step SPACER used for positioning the 20mm Tension Roller on OBD Drive
1x M6 x 25mm HEX Head Bolt - Marine Grade Stainless steel
Weight: 325g

There are 2 sizes of OBD Motor Mounts to choose from. Using the smaller 66T OBD Motor Mount (The 66T means it will fit any Slave Pulley up to 66 Tooth, which is the perfect gearing ratio for 8 inch wheels) its possible to fit any pulley & wheel size up to 8 inches BUT, using the larger 76T OBD Motor Mount you can still fit all the wheels the 66T mount can fit but being larger it can also fit the 9 & 10 Inch wheels. When the 76T mount is used with the smallest wheels, the small wheels make the mounts look a bit out of proportion, but it works fine & then when you then put the big wheels on the proportion is is brought back.... so if you don't ever envisage using 9 or 10 inch wheels then take the smaller OBD Motor mounts, but if you do envisage using larger wheels, then take the 76T OBD Motor Mount so you get all the options you want......

Do you want a REGULAR or GOOFY OBD Mounting Panel?
Do you want a REGULAR or GOOFY OBD Mounting Panel?

76T REGULAR (Left forwards) Mounting Panel - up to 10 inch wheel

76T GOOFY (Right forwards) Mounting Panel - up to 10 inch wheel

What Colour OBD Motor Adaptor with Housed Bearing do you want
What Colour OBD Motor Adaptor with Housed Bearing do you want

BLACK OBD Motor Adaptor with Housed Bearing
BLACK OBD Motor Adaptor with Housed Bearing

BLUE OBD Motor Adaptor with Housed Bearing
BLUE OBD Motor Adaptor with Housed Bearing

BRONZE OBD Motor Adaptor with Housed Bearing
BRONZE OBD Motor Adaptor with Housed Bearing

GOLD OBD Motor Adaptor with Housed Bearing
GOLD OBD Motor Adaptor with Housed Bearing

GREEN OBD Motor Adaptor with Housed Bearing
GREEN OBD Motor Adaptor with Housed Bearing

GUNMETAL OBD Motor Adaptor with Housed Bearing
GUNMETAL OBD Motor Adaptor with Housed Bearing

PINK OBD Motor Adaptor with Housed Bearing
PINK OBD Motor Adaptor with Housed Bearing

PURPLE OBD Motor Adaptor with Housed Bearing
PURPLE OBD Motor Adaptor with Housed Bearing

RED OBD Motor Adaptor with Housed Bearing
RED OBD Motor Adaptor with Housed Bearing

SILVER OBD Motor Adaptor with Housed Bearing
SILVER OBD Motor Adaptor with Housed Bearing

What Colour OBD 20mm Belt Tensioner do you want?
What Colour OBD 20mm Belt Tensioner do you want?

BLACK OBD 20mm Belt Tensioner
BLACK OBD 20mm Belt Tensioner

BLUE OBD 20mm Belt Tensioner
BLUE OBD 20mm Belt Tensioner

BRONZE OBD 20mm Belt Tensioner
BRONZE OBD 20mm Belt Tensioner

GOLD OBD 20mm Belt Tensioner
GOLD OBD 20mm Belt Tensioner

GREEN OBD 20mm Belt Tensioner
GREEN OBD 20mm Belt Tensioner

GUNMETAL OBD 20mm Belt Tensioner
GUNMETAL OBD 20mm Belt Tensioner

PINK OBD 20mm Belt Tensioner
PINK OBD 20mm Belt Tensioner

PURPLE OBD 20mm Belt Tensioner
PURPLE OBD 20mm Belt Tensioner

RED OBD 20mm Belt Tensioner
RED OBD 20mm Belt Tensioner

SILVER OBD 20mm Belt Tensioner
SILVER OBD 20mm Belt Tensioner

Quantity required:
We have enough parts to make…  
RRP £55 - for the complete set

Excluding VAT

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon