This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

TRAMPA PHATLADS 5 spoke DEEP-DISH Off-Set Hubs

TRAMPA PHATLADS 5 spoke DEEP-DISH Off-Set Hubs PHATLADS - 5 Spoke Hub Deep Dish Split Rim hub fits 6,7,8,9 & 10 Inch tyres!! Amazing M4 x 45mm Socket Capped TORX Bolt - Marine Grade Stainless steel with locking paste M4 x 50mm TORX Socket Capped Bolt - Marine Grade Stainless steel with locking paste M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts
RRP
£22.50
inc tax

TRAMPA's 5 Spoke PHATLADS hubs are DEEP-DISH, OFF-SET & the latest addition to TRAMPA’s amazing range of wheels.

Injection molded using premium Dupont plastic composites, PHATLADS Hubs utilize a special split-rim design that can fit any 6, 7, 8 & even 10” tyre that TRAMPA offers – One hub to fit them all will transform your ride experience for sure!

The PHATLADS hubs are known as ‘DEEP DISH’ due to the Angle of the spokes on the fatter part allowing an 'offset bearing position'. Off setting the Bearing position extends the wheelbase & widens the ground contact of any tyres fitted to them.

Weighing just 226g, TRAMPA's PHATLADS are the lightest choice of hub for 9” & 10” Tyres.

There are two sets of Bolt holes on the PHATLADS Hub, these are in an Inner & Outer position. The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the housing on the inner section of the hub. Once the 2 parts are mated together the bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. The Inner bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth with 6 inch tyres, 66 tooth with 8 inch Tyres & 76 Tooth for 9 Inch tyres.... Being able to 'Hot Swap' wheels without taking them apart saves lots of time when it comes to creating / testing different setups, after all a board with 6 inch wheels is completely different to a board with 9 inch. 

TRAMPA's PHATLADS are connected together using 5x M4x45mm with M4 Nuts & use 5x M4x50mm for connecting the wheel into the Slave Pulleys.

Available soon in a selection of colour co-ordinating options, TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's  OPEN BELT DRIVEPRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups....

M4 x 45mm Socket Capped TORX Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 45mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA PHATLADZ HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim, eventually screwing  into the M4 nut on the other side easly.

Weighing just 3 grams each, they are very lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

M4 x 50mm TORX Socket Capped Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA SUPERSTAR HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim of the SUPERSTAR HUB eventually screwing  into the M4 nut on the other side easly.

Weighing just 3 grams each, they are very lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

USED FOR: 
 
SUPERSTAR HUBS
MEGASTAR HUBS

M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts

Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or  8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!

PHATLADS - 5 Spoke Hub Deep Dish Split Rim hub fits 6,7,8,9 & 10 Inch tyres!! Amazing

TRAMPA's 5 Spoke PHATLADS hubs are DEEP-DISH (Extra wide), OFF-SET & the latest addition to fit into TRAMPA’s amazing range of small off road wheels.

Injection molded using premium Dupont plastic composites, PHATLADS Hubs utilize a special 2 parts split-rim design that can fit any 6, 7, 8 & even 10” tyre that TRAMPA offers – One hub to fit them all will transform your ride experience for sure!

Measuring 65mm wide the PHATLADS hubs are a half inch wider than regular 8 inch TRAMPA hubs & are known as ‘DEEP DISH’ due to the Angle of the spokes on the fatter half part, allowing the wider Rim width to sit in the same axle space as a norrower hub, consequentially giving an 'offset bearing position'. Increasing the Rim width increases the ground contact of any tyres fitted to them giving a low wide look when the 6, 7 & 8 inch tyres are fitted & the PHATLADS Hubs are the perfect 65mm width fit for the larger 9 & 10 inch tyres to get maximum surface contact (GRIP) in the muddiest of conditions when contact is needed most!

Currently only available in Natural Black & White with Black Logos the PHATLADS Weigh just 226g per hub (not including the Marine Grade Stainless Steel hardware used to hold them together & fit them to the Pulleys) TRAMPA's PHATLADS are the lightest choice of hub for 9” & 10” Tyres.

There are two sets of Bolt holes running around the perimeter of the PHATLADS Hubs, these are Inner & Outer positions! The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the nut housings on the thinner of the 2 parts & once the 2 parts are mated together the Shorter M4x45mm bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. 

The Inner M4x50mm T20 TORX bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth Slave Pulley when fitted with 6 inch tyres, the 66 tooth Slave Pulley when fitted with 8 inch Tyres & 76 Tooth Slave Pulley when fitting 9 Inch tyres.... Having 2 sets of Bolt holes allows the user to be able to remove the wheel from the assembly without deflating & disassembling the wheel, meaning they can HOT-SWAP their wheel. Being able to 'Hot Swap' your wheels without taking them apart saves you lots of time when it comes to creating different rider setups, after all a board with 6 inch wheels is completely different to a board with 9 inch 

It is possible to fit both the 6001-2RS & 16001-2RS Bearings into the bearing housing of these hubs, of course Bearing reducer sleeves can be used to reduce the bearings from 12mm to either 9.525mm (TRAMPA's Mini Spring Trucks & 12FIFTIES Trucks use 9.525mm Axles) or 10mm axles if your axle should be 10mm not the imperial 9.525mm TRAMPA uses. 

Soon to be available soon in a selection of colour co-ordinating options, TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's  OPEN BELT DRIVEPRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups....

TRAMPA's 5 Spoke PHATLADS hubs are DEEP-DISH (Extra wide), OFF-SET & the latest addition to fit into TRAMPA’s amazing range of small off road wheels.

Injection molded using premium Dupont plastic composites, PHATLADS Hubs utilize a special 2 parts split-rim design that can fit any 6, 7, 8 & even 10” tyre that TRAMPA offers – One hub to fit them all will transform your ride experience for sure!

Measuring 65mm wide the PHATLADS hubs are a half inch wider than regular 8 inch TRAMPA hubs & are known as ‘DEEP DISH’ due to the Angle of the spokes on the fatter half part, allowing the wider Rim width to sit in the same axle space as a norrower hub, consequentially giving an 'offset bearing position'. Increasing the Rim width increases the ground contact of any tyres fitted to them giving a low wide look when the 6, 7 & 8 inch tyres are fitted & the PHATLADS Hubs are the perfect 65mm width fit for the larger 9 & 10 inch tyres to get maximum surface contact (GRIP) in the muddiest of conditions when contact is needed most!

Currently only available in Natural Black & White with Black Logos the PHATLADS Weigh just 226g per hub (not including the Marine Grade Stainless Steel hardware used to hold them together & fit them to the Pulleys) TRAMPA's PHATLADS are the lightest choice of hub for 9” & 10” Tyres.

There are two sets of Bolt holes running around the perimeter of the PHATLADS Hubs, these are Inner & Outer positions! The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the nut housings on the thinner of the 2 parts & once the 2 parts are mated together the Shorter M4x45mm bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. 

The Inner M4x50mm T20 TORX bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth Slave Pulley when fitted with 6 inch tyres, the 66 tooth Slave Pulley when fitted with 8 inch Tyres & 76 Tooth Slave Pulley when fitting 9 Inch tyres.... Having 2 sets of Bolt holes allows the user to be able to remove the wheel from the assembly without deflating & disassembling the wheel, meaning they can HOT-SWAP their wheel. Being able to 'Hot Swap' your wheels without taking them apart saves you lots of time when it comes to creating different rider setups, after all a board with 6 inch wheels is completely different to a board with 9 inch 

It is possible to fit both the 6001-2RS & 16001-2RS Bearings into the bearing housing of these hubs, of course Bearing reducer sleeves can be used to reduce the bearings from 12mm to either 9.525mm (TRAMPA's Mini Spring Trucks & 12FIFTIES Trucks use 9.525mm Axles) or 10mm axles if your axle should be 10mm not the imperial 9.525mm TRAMPA uses. 

Soon to be available soon in a selection of colour co-ordinating options, TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's  OPEN BELT DRIVEPRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups....

PLEASE BE AWARE, THIS IS A PHATLADS PART & WHEN PURCHASED DOES NOT INCLUDE NUTS OR BOLTS. 

TRAMPA's 5 Spoke PHATLADS hubs are DEEP-DISH, OFF-SET & the latest addition to TRAMPA’s amazing range of wheels.

Injection molded using premium Dupont plastic composites, PHATLADS Hubs utilize a special split-rim design that can fit any 6, 7, 8 & even 10” tyre that TRAMPA offers – One hub to fit them all will transform your ride experience for sure!

The PHATLADS hubs are known as ‘DEEP DISH’ due to the Angle of the spokes on the fatter part allowing an 'offset bearing position'. Off setting the Bearing position extends the wheelbase & widens the ground contact of any tyres fitted to them.

Weighing just 226g, TRAMPA's PHATLADS are the lightest choice of hub for 9” & 10” Tyres.

There are two sets of Bolt holes on the PHATLADS Hub, these are in an Inner & Outer position. The Outer set of holes are for the assembly of the Hub & require the M4 nuts being inserted into the housing on the inner section of the hub. Once the 2 parts are mated together the bolt should be threaded through from the fatter side of the hub tightening into then nut with a T20 TORX Key. This M4 nut is submerged & the bolt should not sit proud of the surface of its housing. The Inner bolt holes of the PHATLADS hubs match the same screw pattern as any of the TRAMPA Slave pulleys suiting the 62 Tooth with 6 inch tyres, 66 tooth with 8 inch Tyres & 76 Tooth for 9 Inch tyres.... Being able to 'Hot Swap' wheels without taking them apart saves lots of time when it comes to creating / testing different setups, after all a board with 6 inch wheels is completely different to a board with 9 inch 

TRAMPA's PHATLADS are connected together using 5x M4x45mm with M4 Nuts & use 5x M4x50mm for connecting the wheel into the Slave Pulleys.

Available soon in a selection of colour co-ordinating options, TRAMPA's PHATLADS hubs will fit flawlessly to any of TRAMPA's  OPEN BELT DRIVEPRO BELT DRIVE & SPUR GEAR DRIVE Motor mount setups....

1x 1x PHATLADS Split Rim OFF-SET Deep-Dish 5 Spoke Hubs
5x 5x PHATLADS Stainless Steel Outer Bolt M4x45mm
5x 5x PHATLADS Stainless Steel Inner Bolt M4x50mm
5x 5x M4 Stainless Steel Nylock Nut
Weight: 270g
What colour PHATLADS hubs do you want?
What colour PHATLADS hubs do you want?

Matt Black PHATLADS hubs please
Matt Black PHATLADS hubs please

Gloss White with Black Logo PHATLADS hubs please
Gloss White with Black Logo PHATLADS hubs please

Quantity required:
We have enough parts to make…  
RRP £22.50 - per hub

RRP Includes 20% VAT

Non-EU customers purchase tax-free

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon