Home»Motor Mounts»Mountainboard Motor Mounts»16mm PRO BELT DRIVE Mountainboard Motor Mounts »Spur Gear Drive TO PRO Belt Drive conversion Kit

TRAMPA's Generation III PRO BELT DRIVE Motor Mount is a work of art! Made predominantly from T6 Aluminium, every piece has been precision made to give simple assembly & maximum performance.

The Pro Belt Drive Motor Mount will give you the same kind of performance as experienced when riding an Enduro Motor bike, it uses a lower gearing ratio of 4.71:1 giving a higher top speed when compared to the Spur Gear Drive setup - which has a higher gear ration of 5.9:1 (for better acceleration).

The Gen III Pro Belt Drive Motor Mount will only fit to Precision CNC Hangers, using TRAMPA's special Conical Clamping system to securely attach onto the Hanger. The Assembly of any of the Pro Motor Mounts is incredibly sturdy & robust; perfect for the rough terrain they’ll be ripping across.

Accommodating a 66 Tooth Slave pulley, it is possible to adjust your gearing by swapping between 13, 14 or 15 tooth Motor pulleys.  13 tooth motor pulleys are perfect for hill climbing, whereas 15 tooth pulleys will achieve a higher top speed, & 14s are a nice balance between the two.

You can further adjust the performance by changing the Rear Drive wheel size. Changing from 8” to 9” or 10“ Tyres has a massive effect on the performance of the board. Check out the Pro Belt gearing chart to see estimated top speeds of different tyre & pulley combinations.

It is only possible to fit the TRAMPA 5 Spoke Hubs to Pro Drive Slave Pulleys. This means the 5-Spoke Superstar & Megastar wheels fit no problem. However it is only possible to run 8 – 10 inch tyres on the Pro Drives, due to low clearance around the housing tubs.

Enclosed within the Motor Mount tub is the Belt Tension Roller - a Bearing Mounted in Aluminium housing, that guides the belt into the optimum position/tension, to maintain the max amount of grip between the belt & the pulley.

Its possible a belt can snap for a variety of reasons. If you’re the kind of rider that likes to go off into the wilderness, then you should always ride with a couple of spare belts (when one snaps, chances are the other isn’t far off).  TRAMPA's Pro Belt Drive utilises two special cut-outs that ‘ejects’ broken belts from the housing – slimming the chances of snapped belts jamming up the Motor Pulley.

The best way to prevent a belt snap is to check over & replace the Pulleys & belts on a semi-regular basis - BEFORE they have chance to fail on you. Riding, accelerating & braking hard will wear out your belts & pulleys faster. We recommend you service your board every three rides, or after any particularly tough ride. Check the hardware is tight, the belts aren’t worn, & for any damage, particularly to the motor mounts/trucks. Ensure the tub is free from any dust/dirt. Servicing your board is important for keeping it running smoothly, as well as for your safety when riding.

Belt Tension Roller Housing for 15mm Belts - SILVER

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

Made from T6 Heat-treated Aluminium, these Belt Tension Rollers are to designed to house a premium TRAMPA 608 BEARING, ensuring a smooth and consistent roll while tensioning the belts. Used with 15mm belts on PRO BELT or OPEN BELT DRIVE, as well as MKII Urban Carve Motor Mounts.

Sprung Steel C-CLIP used inside the Belt tension housings to secure 608 bearing

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

These C-Clips ensure the 608 bearing is secure within the Tension Rollers

Step SPACER used for positioning the 15mm Tension Roller on OBD Drive

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

These Spacer-Axles have two functions, correctly positioning the 20mm Tension Roller, as well as providing the housed 608 bearing a snug-fitting axle to spin freely on.

415 long x 16mm wide High Torque Drive (HTD) 5M (5mm Tooth Space) High Power (HP) STRONGBELT for 2020 Mountainboard Pro Motor Mounts

This ia 416mm long x 16mm wide High Torque Drive (HTD) Re-enforced Rubber Belt, which has 5mm Tooth Spacing (5M). This Belt is High Power rated (HP) & arguably over engineered for our application as the belt is made in Germany by the world famous company called STRONGBELT, who usually supply into heavy industry public sector applications which demand much more stringent requirements of any electric skateboard! This belt is used to transfer the power from the Motor & Motor Pulley into power at the rear wheels of a TRAMPA Electric Mountainboard.

TRAMPA opted to set a new standard in E-Skating, becoming the first in the world to fit to all of its E-Boards, a 15mm wide TRANSMISSON BELT. Our standard 15mm belt is almost double the width of nearly all other E-Sk8's out there, they tend to use a flimsy off the shelf 9mm transmission belt which are prone to stretch, slip & ultimately snap. Using a re-enforced 15mm wide High Power Belt reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. When accelerating or engine breaking (KERS), even from a standing start the STRONGBELT power is smooth & does not slip, or strain the motor, it does a damn gooood job!.....

STRONGBELT, as their name suggests, is a Heavy Industry German Brand that usually supplies the likes of Train manufacturers where serious levels of quality with no excuses on failure are expected from the product, as failure for such an item is serious & may result in death! STRONGBELT weave KEVLAR into their Pulley Belts, Kevlar is one of the strongest fibers known to man, its often added into materials to gain extra strength.... STRONGBELT have the best reputation in the Power Transmission Industry for NO stretching or snapping & we have high expectations from this quality item. 

These extra quality details in the production of our electronic motor drives, provides the maximum responsiveness achievable whilst maintaining a super smooth power delivery to the rider at all times. 

66 Tooth x 16mm wide Slave Pulley with Pressed bearing for axle support - Fits best to 8 inch wheels for V2 & V3 PRO BELT Drive Motor Mounts with 16mm Belts

TRAMPA's 66 Tooth Pro Motor Mount Slave Pulley fits to any of TRAMPA's 8 Inch off road wheels when connecting into the Mountainboard PRO Motor Mount system. The 66 tooth Pulley has been precision milled from super-light-weight & mega strong Heat Treated T6 Aluminum. The pulleys teeth stand 5mm tall, this is the same size teeth as that found on TRAMPA's 15mm wide 'Strongbelt' & when TRAMPA's 460x15mm Premium Strongbelt is wrapped around the pulleys & the belt tension facility has been screwed down the connection between the teeth & the belt becomes so strong it has what we call HIGH TORQUE DRIVE (HTD).  HTD ensures all of the motors Torque is forced through the pulleys to the wheels & when coupled with the amazing VESC 6 & 12s Battery power provides instant smooth unreal Power on tap to the rider!

This 66 tooth Pro Mount Slave Pulley is capable of connecting to all of the wheels (7, 8 & 9 Inch) in the TRAMPA range but we (TRAMPA) only use it when assembling 8 inch TRAMPA wheels into the TRAMPA Pro Motor Mounts! 

But with the use of some very special Threaded Hex Spacers & Socket capped Bolts the 66 Tooth Pro Mount Slave Wheel connects directly to any of the 7 or 8 Inch SUPERSTAR or HYPA Wheel s& very uniquely also into the 3 spoke PRIMO 9 Inch Wheel as well - 1 pulley, 3 uses.... :-)

TRAMPA's special 66 tooth Pro Mount Slave Wheel works in conjunction with all & any of the 13, 14 or 15 tooth Motor Pulley in the range. Changing your Motor Pulley will drastically alter the performance & characteristics of your ride... 13 Tooth is best for Hill Climbing whilst 15 Tooth is best for high speed, 14 tooth will give you all round performance...

To connect to HYPA hubs you'll need 6x 17x4mm Threaded Hex spacers
To connect to SUPERSTAR hubs you'll need 5x 15x4mm Threaded Hex spacers
 

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x8mm

TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.

TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....

Custom 15mm wide Motor Pulley 13, 14 or 15 tooth

TRAMPA's 15mm wide 13-15 Tooth Motor Pulleys connect directly to the Motor Axle & are secured into position using a Magnetic Fixing Key & 4mm Locking Grub Screw.

These custom made Motor Pulley Wheels  fit 15mm wide STRONGBELTS, which should never stretch or break whilst at the same time providing a very smooth power delivery to the user - even from a standing start.

Choice of Aluminium or Black Steel. Aluminium Pulleys are perfect for those looking to save every gram possible on their board - Black Steel Pullys are heavier, but much harder wearing.

Changing your Motor Pulley &/or Drive pulley wheels will drastically change the performance of your ride... :-)

13 Tooth
Best performance for climbing steep inclines.

14 Tooth 
Best all-round performance

15 Tooth 
Best performance forreaching top speeds.

PRO BELT TUB - Fits to both V2 16mm & V3 20mm Pro Belt Tub Covers

CNC’d from a solid block of T6 heat-treated Aluminium, the V3 PRO BELT MOTOR MOUNT TUB is built around keeping the drive train securely & accurately attached, while running as smoothly as possible. Paired with the specially designed CNC’d COVER, the completed tub keeps the elements outs, the gears & belts clean & dry, & the whole board running smoothly.

Attaching T6 Aluminium BASH GUARDS (left & right) ensures the Tub will survive every knock & bump the drive system is bound to receive on a ride.
Special cutouts on the sides of tub allow snapped belts to be ejected out & away from the drive train, preventing any jammed gears or wheel lock.

The Tub is perfectly symmetrical allowing it to slide onto left or right drive trains.

16mm BELT PRO Belt TUB COVER - V2

The Pro Belt Tub Cover is crucial to keeping your drive system free of dirt & debris. CNC’d from Premium Aluminium, giving it the perfect weight-to-strength ratio, the cover slots tightly over the Pro Belt Tub, perfectly sealing off the drive system.

PRO Belt Motor Mount Bash Guard PRO 16mm Belt LEFT

Made using hardened steel, the PRO BELT bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the left drivetrain.

PRO Belt Motor Mount Bash Guard PRO 16mm Belt RIGHT

Made using hardened steel, the PRO BELT bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the right drivetrain.

16mm PRO Belt Drive Motor Connector with 608 Bearing - SILVER ONLY

Housing a precision bearing for Motor Axle Support the PRO BELT DRIVE Motor Adaptor is used for attaching the motor securely to the drivetrain.
Precision CNC’d from hardened steel, the Motor Adaptor also allows for the use of PRO MOTOR HOUSING.

Mountainboard Motor Mount V-Ring TUB Seals - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

M4 x 10mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 4mm Grub Screw M4 x 4mm Motor Pulley Grub Screw - Connects the Motor Pulley onto the Motor Axle Shaft

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M6 x 25mm Bolt - Fixes Trucks to HolyPro Decks - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

You’ll need 8 of the TRAMPA M6 x 25mm Marine Grade Stainless Steel Bolts & 8 of the TRAMPA M6 Stainless Steel Nylock Nuts to attach a pair of TRAMPA Skate Trucks to any TRAMPA Deck with Risers. You’ll also need a pair of 10mm ring spanners to tighten and loosen the Nuts & Bolts. Don’t forget to make sure you’re Nuts & Bolts are tight before you ride!

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.