This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.
TRAMPA's 6 spoke HYPA Hub is by far the sexiest, as well as being the strongest, 3.75-inch hub on the market today!
The HYPA hubs 6 spoke design is technically advanced & is manufactured using original Du-Pont materials & the very latest in precision injection molding machinary - No quality expense is spared! This delux combination of technical design, top quality machinary & original genuine materials, creates a product that is far superior to all of our competitiors, resulting in performance that is well beyond normal expectations. This extra performnce means the TRAMPA HYPA hub can handle much higher than recommended tyre inflation pressures, generting substantially higer than normal roll speeds. During testing our crash test dummies (i mean the Team riders) commonly rode with these hubs well above 80psi & beyond.... When resting at the top of the mountain we measued Joels pressure at 110psi! (110 psi is not recommended!)
The HYPA hubs are held together using only the best Marine Grade (A4) Stainless steel Nuts & Bolts so they definitly wont rust on you (EVER) & are therfore perfect for bad conditions. All the Bolts used by TRAMPA have been dipped in a special Blue Locking Paste & all the Nuts are fitted with the world renowned Nylon "Nylock" Nut locking System, all these no expense spared small details ensure you get the absolute best hub possible!
HYPA hubs are available in loads of different colours & surface finishes, all of which are TRAMPA embossed between the spokes proving the top quality! Do not buy imitations as they will not perform the same! TRAMPA’s own high class Steel Bearings, (Genuine ABEC 5 rated Bearings) push perfectly into the HYPA hub bearing housing, guaranteeing the fastest spin rate to the wheel possible. Use either Bearing reducer sleeves into 12mm Bearings or use TRAMPA's 10mm Bearings to fit the HYPA hubs onto 9.52mm skate axles. HYPA hubs are compatible with all known 8-inch tyres currently on the market including MBS & Scrub. Put quite simply – HYPA hubs are by the Best!
Along with many other applications that these wheels will fit too, the HYPA hub will fit and accept ALL the other brands of mountainboards on the market including MBS, SCRUB & KHEO, so when you are looking for an upgrade to your ride you know where too look! Basically the HYPA will fit to anything that uses a Imperial 7/16ths (9.52mm) or 12mm bearings to fit onto the axle. If you already have your own 12mm bearings there are conversion spacers available to convert your 12mm bearings to work on the 7/16ths Imperial (9.52mm) skate axles and a different size spacer to convert them to fit 10mm (metric) scooter axles (see associated parts for details).
Bearings are supplied at a discounted price when purchased with hubs... TRAMPA ABEC 5 Bearings are normally £1.88 each (£15 per set of 8) but when they are purchased with a set of hubs they work out at only £1.25 each which is only £10 per set of 8 bearings when purchased with hub set) giving you a £5 Saving per set!
TRAMPA's M4 x 35mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the TRAMPA HYPA HUBS. The socket capped head of the Bolt fits neatly into the Bolt housing of the HYPA HUB marrying into the M4 nut located in the housing on the other side of the hub.
Weighing just 3 grams each these bolts are very lightweight. They look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.
You will need a 3mm Allen Key to tighten & loosen the Nuts & Bolts from the hub. Ensure all your Nuts & Bolts are tight before riding!
Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts.
This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or 8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!
TRAMPA's 6 spoke HYPA Hub is the lightest, strongest injection moulded 8 inch hub / wheel on the market today. Produced using original DuPont ingredients & the very latest in injection moulding machinery, no quality expense is spared!! HYPA Hubs are so strong, during testing our Crash Test Dummies (i mean the Team Riders) frequently inflated their HYPA wheels well beyond 75psi with no problems to report!
HYPA Hubs are available in loads of coordinating colours all of which are TRAMPA embossed proving our top quality, so to avoid disappointment dont go buying imitations! Our top quality continues as the HYPA Hubs construction uses A4 (Marine Grade) Stainless Steel Nuts & Bolts which are guaranteed never to rust.
HYPA Hubs are compatible with all known 8 Inch Tyres on the market today.
TRAMPA’s very own & genuine ABEC rated Bearings push perfectly into the HYPA Hub, guaranteeing the fastest spin rate possible. Use 12mm bearings (12x28x8mm) for 12mm axles or you can use Bearing Reducer Sleeves to fit your existing 12mm bearings onto 10mm axles (9.52mm or 7/16ths inch axles). 9.52x28x8mm bearings also fit TRAMPA hubs to 9.52mm Skate Axles.
Bearings are supplied at a discounted price when purchased with a set of hubs...
2 x Bearings cost only £2.50 x 4 = £10 per set of 8 making a £5 saving per set!
The amazing 125mm GUMMIES Tyres are a 'Revolution' in the world of boarding. The Gummies Tyres fit too & transform the performance of TRAMPA's HYPA, SUPERSTAR or MEGASTAR hubs, converting pneumatic wheels into Supersized Longboard-style wheels & giving a completely new boarding sensation!
The larger 125mm size allows GUMMIES Wheels to glide over cracks in the pavement & smash through smaller obstacles that can get in the way & jam up smaller sized wheels.
Using premium SUPERSOFT Urethane (75a) with 50mm of surface-contact, GUMMIES perform like their name suggest & stick to the streets like gum on asphalt - allowing the most insane turns & carves you wouldn’t believe possible.
The 44-tooth Slave Pulley was produced to work in harmony with GUMMIES & TRAMPA’s range of Belt-Drive Motor Mounts, giving the optimal amount of clearance between the pulley & the ground. GUMMIES tyres can fit to Electric Longboards, Carveboards & Urban Mountainboards.
Available in Black, Blue or Red.
Sets of 4 Tyres & Tubes available at a discounted price at this link
Sets of 4 Tyres & Tubes available at a discounted price at this link
HYPA Hubs have a 3.75 x 2 inch rim & will fit all tyres up to 8 inches in diameter.
The HYPA hub is time-proven as being one of the best hubs on the market - We’ve sold tens of thousands of them throughout the years for countless applications - & to this day problems are a rare occurrence!
Made from premium DuPont Plastics, the 6-spoke Hypa hub has an amazing strength-to-weight ratio – weighing just 125g each, they’re the lightest hub in the TRAMPA range! Perfect for freestylers looking to lose every gram off of their board!
Available in a huge range of colours / patterns!
HYPA Hubs use a 2-piece centre-set split-rim design, held together using 6x m4 x 35mm Socket Cap Bolts. Once assembled, can handle up to 50 PSI!
Oversized Longboard Wheels - being 125mm in Diameter, GUMMIES are much larger than any other Longboard wheel on the market! Using High-Quality SUPER SOFT Urethane (75a) with 50mm wide surface contact GUMMIES perform like their name suggests - they’ll grip like gum to the pavement - allowing the most insane turns you wouldn’t believe possible! Thanks to their larger size, GUMMIES Wheels glide over cracks in the pavement & smash through the obstacles that would stop smaller wheels dead.
We all know the pavements & roads are far from a perfect surface - so much so that sometimes it's almost impossible to ride with Longboard wheels. The design brief for the 6.5 inch URBAN TREAD Tyre was simple - make the smallest, best quality pneumatic tyre possible.
The intelligent Jagged-Grip design can be run on high or low inflation pressures. Low pressure gives more grip for muddy corners & trails. High Pressure is perfect for flat-out straight-line speeds! High quality rubber compound & a high TPI (thread-count per inch) make this hub light-weight & hard-wearing!
7” Tyres are a good balance of size & weight. While still big enough to handle rough terrains & build up to impressive rolling speeds, the smaller size helps to save on weight.
7” INNOVA INLINES - With straight cut tread & the ability to handle high PSI, the INLINE is the perfect option for easy rolling. Working best on smooth surfaces such as skate parks, tarmac or asphalt, the 3mm deep ‘In Line’ grooved surface, encourages the tyre to track in a straight line! Unlike standard Longboard/street style wheels, the pneumatic INLINE tyre is easily big enough to glide over cracks, stones or holes, & will handle hard-packed rougher terrain, such as gravel path with no problem.
7” MUD PLUGGERS- Using a deep & aggressive tread pattern that creates 'Grip on top of Grip', with straight sidewalls and a rigid rubber structure, MUD PLUGGERS have a box-ier shape that increases surface contact. Able to run on both low & high PSIs, the wide center bead both reduces rolling resistance and improves traction! Produced using a soft 2PR rubber compound with a high TPI (thread-count per inch), the resulting tyre is amazingly grippy & hard-wearing!
8” Tyres are the first choice for many riders, and are generally considered the “industry standard” when it comes to Mountainboard wheel sizes. Being so popular, and the perfect size for many applications, we offer a HUGE range of 8” tyres!
8” TRAMPA TREAD TYRES - A time-tested favourite among team riders, the TRAMPA TREAD uses an aggressive tread pattern and a choice of hard or soft rubber compound, these Tyres are a solid choice for most terrains! SOFT COMPOUND TREADS are ideal for riding on hard-packed surfaces, whereas HARD COMPOUND TREADS are much better gripping in softer mud.
8” PRIMO ALPHA TYRES - Using a soft 2PR rubber compound & high TPI (thread-count per inch) - PRIMO ALPHAS are light-weight, grippy & hard-wearing! Its design incorporates a wide center bead to allow & maintain straight line speed, whilst the surrounding tread is beautifully sculpted with wide grooves that’ll give traction regardless of the terrain!
8" PRIMO STRIKER TYRE - A favourite among boarder-X racers, the PRIMO STRIKER was designed for fast riding on hard-packed dirt. Made using a hard rubber compound with a Wide Center Bead to help achieve the maximum rolling speeds. The close cut grip pattern around the sides of the tyre gives loads of grip on changeable terrain.
8" MUD PLUGGER TYRES - using a deep & aggressive tread pattern that creates 'Grip on top of Grip', with straight sidewalls and a rigid rubber structure, MUD PLUGGERS have a box-ier shape that increases surface contact. Able to run on both low & high PSIs, the wide center bead both reduces rolling resistance and improves traction! Produced using a soft 2PR rubber compound with a high TPI (thread-count per inch), the resulting tyre is amazingly grippy & hard-wearing!
8” DIAMOND TREAD TYRE - Made from relatively soft rubber with a close-cut tread pattern & a ballooned-shape, the DIAMOND TREAD Tyre is a perfect all rounder option, giving great grip on hard surfaces & good grip when heading off road - especially during the summer months.
8" INNOVA INLINE TYRE With straight cut tread & the ability to handle high PSI, the INLINE is the perfect option for easy rolling. Working best on smooth surfaces such as skate parks, tarmac or asphalt, the 3mm deep ‘In Line’ grooved surface, encourages the tyre to track in a straight line! Unlike standard Longboard/street style wheels, the pneumatic INLINE tyre is easily big enough to glide over cracks, stones or holes, & will handle hard-packed rougher terrain, such as gravel path with no problem.
8" INNOVA SLICKCUT TYRE - Kevlar banding, a high TPI (thread-count per inch), & hard compound rubber make the INNOVA SLICKCUT a light-weight & amazingly strong tyre. The Kevlar banding allows the tyres to handle insane inflation rate, paired with a tread pattern suited for hard surfaces, this is the ultimate tyre for high speed road racing!