This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

66T Open Belt Drive OBD Motor Mount with 66 tooth Pulley Kit for 8 inch Wheels & Motor Protection - TWIN

66T Open Belt Drive OBD Motor Mount with 66 tooth Pulley Kit for 8 inch Wheels & Motor Protection - TWIN 66T OPEN BELT DRIVE Motor Mount & Motor Adaptor - TWIN BLACK Open Belt Drive 8 Inch Wheel 66 Tooth Pulley Kit with  415mm x 20mm Belt for 8 Inch Wheels 2x ORIGINAL Open Belt Drive Motor protection Sleeve with Stainless Steel Filter & Ejot Screws for fixing
RRP
£300
exc tax

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

M6 x 25mm Bolt - Fixes Trucks to HolyPro Decks - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

You’ll need 8 of the TRAMPA M6 x 25mm Marine Grade Stainless Steel Bolts & 8 of the TRAMPA M6 Stainless Steel Nylock Nuts to attach a pair of TRAMPA Skate Trucks to any TRAMPA Deck with Risers. You’ll also need a pair of 10mm ring spanners to tighten and loosen the Nuts & Bolts. Don’t forget to make sure you’re Nuts & Bolts are tight before you ride!

M6 x 25mm Socket Capped Allen-Key Bolt for OBD Mounts & Scooter Clamps

TRAMPA's M6 x 30mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the PRIMO 3 Spoke Hubs. The socket capped head of the Bolt screws neatly though the HUB eventually screwing into the Marine Grade Stainless Steel M6 Nylock Nut on the other side of the hub. 

Weighing just 8 grams each, these Bolts are lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers nuts & bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You’ll will need a 5mm Allen Key  to tighten & loosen the Bolt from the nut. Ensure all your Nuts & Bolts are tight before riding!

M4 x 4mm Grub Screw M4 x 4mm Motor Pulley Grub Screw - Connects the Motor Pulley onto the Motor Axle Shaft

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 20mm Socket Capped Head TORX Bolt ISO 4762 Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt DIN6912 Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt DIN6912 Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

415 long x 20mm wide High Torque Drive (HTD) 5M (5mm Tooth Space) STRONGBELT for Open Belt Drive Motor Mounts

This ia 460mm long x 15mm wide High Torque Drive (HTD) Re-enforced Rubber Belt, which has 5mm Tooth Spacing (5M). This Belt is High Power rated (HP) & arguably over engineered for our application as the belt is made in Germany by the world famous company called STRONGBELT, who usually supply into heavy industry public sector applications which demand much more stringent requirements of any electric skateboard! This belt is used to transfer the power from the Motor & Motor Pulley into power at the rear wheels of a TRAMPA Electric Mountainboard.

TRAMPA opted to set a new standard in E-Skating, becoming the first in the world to fit to all of its E-Boards, a 15mm wide TRANSMISSON BELT. Our standard 15mm belt is almost double the width of nearly all other E-Sk8's out there, they tend to use a flimsy off the shelf 9mm transmission belt which are prone to stretch, slip & ultimately snap. Using a re-enforced 15mm wide High Power Belt reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. When accelerating or engine breaking (KERS), even from a standing start the STRONGBELT power is smooth & does not slip, or strain the motor, it does a damn gooood job!.....

STRONGBELT, as their name suggests, is a Heavy Industry German Brand that usually supplies the likes of Train manufacturers where serious levels of quality with no excuses on failure are expected from the product, as failure for such an item is serious & may result in death! STRONGBELT weave KEVLAR into their Pulley Belts, Kevlar is one of the strongest fibers known to man, its often added into materials to gain extra strength.... STRONGBELT have the best reputation in the Power Transmission Industry for NO stretching or snapping & we have high expectations from this quality item. 

These extra quality details in the production of our electronic motor drives, provides the maximum responsiveness achievable whilst maintaining a super smooth power delivery to the rider at all times. 

Belt Tension Roller Housing for 20mm Belts

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

Made from T6 Heat-treated Aluminium, these Belt Tension Rollers are to designed to house a premium TRAMPA 608 BEARING, ensuring a smooth and consistent roll while tensioning the belts. Used with 20mm belts on OPEN BELT DRIVE Motor Mounts.

 

 

Sprung Steel E-CLIP used inside the Belt tension housings to secure 608 bearing

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

These C-Clips ensure the 608 bearing is secure within the Tension Rollers

 

Step SPACER used for positioning the 20mm Tension Roller on OBD Drive

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

These Spacer-Axles have two functions, correctly positioning the 20mm Tension Roller, as well as providing the housed 608 bearing a snug-fitting axle to spin freely on.

OBD Open Belt Drive Motor Mount Connector Panel for 66 tooth Pulleys - GOOFY

OBD Motor Mount Connector Panels are an all-in-one Mounting Panel & Truck connector, CNC’d from premium heat-treated T6 aluminium. Motor Mount Connector Panels are available in two models (66T or 76T), each designed with different gear ratios (therefore different performances) in mind.  

OBD 66T fits the 66 tooth Slave Pulley, with a gear ratio of 4.71:1 - giving a top speed ~36mph, and performance favouring eye-watering top speeds over acceleration. OBD 66T Systems can use 8 or 9 inch Wheels.

Attaches to the Motor Adaptor using 4x M4x10 Dome Headed Bolts & 1x M4x20 Socket Capped Bolt
Attaches to the Truck using 1x M6x25 Socket Capped Bolt.

OBD Open Belt Drive Motor Mount Connector Panel for 66 tooth Pulleys - REGULAR

OBD Motor Mount Connector Panels are an all-in-one Mounting Panel & Truck connector, CNC’d from premium heat-treated T6 aluminium. Motor Mount Connector Panels are available in two models (66T or 76T), each designed with different gear ratios (therefore different performances) in mind.  

OBD 66T fits the 66 tooth Slave Pulley, with a gear ratio of 4.71:1 - giving a top speed ~36mph, and performance favouring eye-watering top speeds over acceleration. OBD 66T Systems can use 8 or 9 inch Wheels.

Attaches to the Motor Adaptor using 4x M4x10 Dome Headed Bolts & 1x M4x20 Socket Capped Bolt
Attaches to the Truck using 1x M6x25 Socket Capped Bolt.

Open Belt Drive Motor Adaptor with Housed Bearing Connects with Both the 66 & the 76 Tooth Motor Mounts

The Open Belt Drive Motor Adaptor has been precision CNC’d from heat-treated T6 Aluminium to fit securely to the 66T or 76T OBD Motor Mount Connector Panels. 

Able to fit any TRAMPA motor in the range, the OBD Motor Adaptor can also fit the amazing looking PRO DELRIN Motor covers. 

Attaches to the Motor Mount Connector Panels using 4x M4x10 Dome Headed Bolts & 1x M4x20 Socket Capped Bolt
Attaches to Motors using 4x M4x10 Dome Headed Bolts. 
Attaches to DELRIN Motor Covers using 5x 3.5x12 Plastic Thread Cutting Bolts

Custom 20mm wide Steel Motor Pulley 13, 14 or 15 tooth

TRAMPA's 20mm wide 13-15 Tooth Motor Pulleys connect directly to the Motor Axle & are secured into position using a Magnetic Fixing Key & 4mm Locking Grub Screw.

This custom made Motor Pulley Wheel  fits 20mm wide STRONGBELTS, which should never stretch or break whilst at the same time providing a very smooth power delivery to the user - even from a standing start.

Changing your Motor Pulley &/or Drive pulley wheels will drastically change the performance of your ride... :-)

13 Tooth (40g)
Best performance for climbing steep inclines.

14 Tooth (48g)
Best all-round performance

15 Tooth (60g)
Best performance forreaching top speeds.

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x8mm

TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.

TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....

66 Tooth Slave Pulley with Pressed bearing - 20mm OPEN BELT DRIVE Motor Mounts

As the 20mm wide 66 Tooth OBD Pulley is supported / mounted on the axle with a press fitted bearing, when you then include the 2x bearings in the wheel, there are therefore 3 points of mounting contact on the axle in the assembly of the Motor drive when fixing to the wheel giving a very nice well balanced secure fit ensuring maximum performance at all times.
The power of the TRAMPA Motors is huge & to have the power spread across the axle is important to the delivery of smooth performance...
The 66 Tooth Pulley needs to be correctly positioned on the axle to ensure the belts align perfectly with a  9.5mm spacer.
So if you don't already have one, then you WILL NEED a 12x 16x 9.5mm Spacer to position the pulley & wheel in the perfect location on the axle to acquire maximum Torque 

You may also need some M4 x 20mm Hex spacersM4 x 10mm Dome Head TORX Bolts to fit this pulley to your wheel.... 
As this Pulley has 5 spokes, it is specifically designed to only fit to any the 5 spoke hubs that TRAMPA produces. So TRAMPA's SUPERSTAR 8 or 9 inch Megastar & PHATLADS hubs...

M4 x 20mm Hex Spacer - 5 Spoke Wheels to Slave Wheels on OBD & ORRSOM Boards

Used for connecting Slave Pulleys to Hubs using a 12-FIFTIES Motor Mount. 

x5 Required for HYPA hubs
x6 Required for SUPERSTAR / MEGASTAR hubs

This simple motor mounting kit is as versatile as they come - able to work with most Mountainboard Trucks and wheels - as well as a huge variety of motor & pulley sizes.

Essentially, this kit is the barebones of your motor system - giving you the freedom to pick, choose, and customise what your final product will be!

The Motor Mount Connectors snuggly slide over the truck hanger and are secured tightly with MARINE GRADE M6x10 grub screws. The Premium Quality Carbon Mounting Panel is secured to the Motor Mount Connector. Compatible with Electric Motors with long or short Motor Axles - you’ll be able to fit any electric motor you wish.

In this kit you get the following items -
In this Kit you get the following parts -
1x OBD Open Belt Drive Motor Mount Connector Panel for 66 tooth Pulleys - GOOFY
1x OBD Open Belt Drive Motor Mount Connector Panel for 66 tooth Pulleys - REGULAR
2x M6 x 25 Socket cap Allen-Key Stainless Steel Bolt
2x OBD Motor Adaptor with Housed Bearing
2x TRAMPA abec 7 608 or Si4n5 Ceramic Longboard & Skateboard Bearings
8x M4 x 10 Dome Headed TORX Bolt
2x M4 x 20 Socket Cap TORX Bolt
2x 20mm Stainless Steel Tension Roller Housing for 20mm Belts
2x TRAMPA abec 7 608 or Si4n5 Ceramic Longboard & Skateboard Bearings
2x Sprung Steel E-CLIP for Belt tension roller secures 608 bearing in position.
2x Step SPACER used for positioning the 20mm Tension Roller on OBD Drive
2x M6 x 25mm HEX Head Bolt - Marine Grade Stainless steel
2x 20mm Steel Motor pulley Custom option 13, 14 or 15 Tooth
2x M4 x4mm Hardened BLACK Steel Grub Screw - Locks Motor Pinion on Axel
2x Motor Pulley M3 x3 x12mm Keyway for 2mm Pulley
12x Pully mounting Spacer Nuts - excluded cost add attriburte
2x Slave Pulley for URBAN Mountainboard
12x Bolts for fixing 44 tooth Slave Pulley to Hypa hubs M4x40
2x STRONGBELT 415 x 20mm HTD 5M HP - OBD 66 Tooth Motor Mounts
2x Super strong DELRIN Plastic Motor Protection HOUSING Open Ended
2x MkII Motor Protection Sleeve Stainless Steel Mesh FILTER
12x M3.5 x 10 Countersunk TORX Plastic EJOT Screws
Weight: 1,366g

This Pulley can be fitted to 6 spoke HYPA hubs or 5 spoke SUPERSTAR, MEGASTAR 8 & 9 Inch, PHATLADS wheels, Are you fitting 5 or 6 spoke hubs so we can send you the coreect Stand off Hex Spacer nuts

Are you fitting this Slave Pulley to 6 Spoke HYPA or 5 Spoke TRAMPA Wheels?
Are you fitting this Slave Pulley to 6 Spoke HYPA or 5 Spoke TRAMPA Wheels?

Please give me spacer nuts to fit 6 Spoke HYPA hubs
Please give me spacer nuts to fit 6 Spoke HYPA hubs

Please give me Spacer nuts to fit 5 Spoke Superstar, Megastar or Phatlads
Please give me Spacer nuts to fit 5 Spoke Superstar, Megastar or Phatlads

There are 2 sizes of OBD Motor Mounts to choose from. Using the smaller 66T OBD Motor Mount (The 66T means it will fit any Slave Pulley up to 66 Tooth, which is the perfect gearing  ratio for 8 inch wheels) its possible to fit any pulley & wheel size up to 8 inches. Using the larger 76T OBD Motor Mount you can still fit all the wheels the 66T mount can fit but being larger it can also fit the 9 & 10 Inch wheels. When the 76T mount is used with the smallest wheels, the small wheels make the mounts look a bit out of proportion, but it works fine & then when you then put the big wheels on the proportion is is brought back.... so if you don't ever envisage using 9 or 10 inch wheels then take the smaller OBD Motor mounts, but if you do envisage using larger wheels, then take the 76T OBD Motor Mount so you get all the options you want......

Do you want to run up to 8 Inch Wheels or up to 10 Inch Wheels
Do you want to run up to 8 Inch Wheels or up to 10 Inch Wheels

66T TWIN Mounting Panels to fit up to 8 inch wheels

76T TWIN Mounting Panels to fit up to 10 inch wheels

What Colour 66T TWIN OBD Motor Mount Connector Panel do you want?
What Colour 66T TWIN OBD Motor Mount Connector Panel do you want?

BLACK 66T TWIN OBD Motor Mount Panels
BLACK 66T TWIN OBD Motor Mount Panels

BLUE 66T TWIN OBD Motor Mount Panels
BLUE 66T TWIN OBD Motor Mount Panels

BRONZE 66T TWIN OBD Motor Mount Panels
BRONZE 66T TWIN OBD Motor Mount Panels

GOLD 66T TWIN OBD Motor Mount Panels
GOLD 66T TWIN OBD Motor Mount Panels

GREEN 66T TWIN OBD Motor Mount Panels
GREEN 66T TWIN OBD Motor Mount Panels

GUNMETAL 66T TWIN OBD Motor Mount Panels
GUNMETAL 66T TWIN OBD Motor Mount Panels

PINK 66T TWIN OBD Motor Mount Panels
PINK 66T TWIN OBD Motor Mount Panels

PURPLE 66T TWIN OBD Motor Mount Panels
PURPLE 66T TWIN OBD Motor Mount Panels

RED 66T TWIN OBD Motor Mount Panels
RED 66T TWIN OBD Motor Mount Panels

SILVER 66T TWIN OBD Motor Mount Panels
SILVER 66T TWIN OBD Motor Mount Panels

What size Motor you would like...
What size Motor you would like...

6364 160Kv TRAMPA Motor - Even more amazing speed!
6364 160Kv TRAMPA Motor - Even more amazing speed!

6376 160Kv TRAMPA Motor - Only for the Insane! (+£50)
6376 160Kv TRAMPA Motor - Only for the Insane! (+£50)

6376 185Kv Motor - The fastest yet!! (+£50)
6376 185Kv Motor - The fastest yet!! (+£50)

What size Motor Pulley you would like?
What size Motor Pulley you would like?

13 Tooth 20mm wide Motor Pulley - BEST Hill Climber
13 Tooth 20mm wide Motor Pulley - BEST Hill Climber

14 Tooth 20mm wide Motor Pulley - BEST All Round
14 Tooth 20mm wide Motor Pulley - BEST All Round

15 Tooth 20mm wide Motor Pulley - BEST Top Speed
15 Tooth 20mm wide Motor Pulley - BEST Top Speed

Quantity required:
We have enough parts to make…  
RRP £300 - for the complete set

Excluding VAT

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon