Home»Motor Mounts»Mountainboard Motor Mounts»20mm PRO BELT DRIVE Mountainboard Motor Mounts »20mm PBD Motor Mounts with FILTERS - NO Pulleys & NO Motors

TRAMPA's Generation III PRO BELT DRIVE Motor Mount is a work of art! Made predominantly from T6 Aluminium, every piece has been precision made to give simple assembly & maximum performance.

The Pro Belt Drive Motor Mount will give you the same kind of performance as experienced when riding an Enduro Motor bike, it uses a lower gearing ratio of 4.71:1 giving a higher top speed when compared to the Spur Gear Drive setup - which has a higher gear ration of 5.9:1 (for better acceleration).

The Gen III Pro Belt Drive Motor Mount will only fit to Precision CNC Hangers, using TRAMPA's special Conical Clamping system to securely attach onto the Hanger. The Assembly of any of the Pro Motor Mounts is incredibly sturdy & robust; perfect for the rough terrain they’ll be ripping across.

Accommodating a 66 Tooth Slave pulley, it is possible to adjust your gearing by swapping between 13, 14 or 15 tooth Motor pulleys.  13 tooth motor pulleys are perfect for hill climbing, whereas 15 tooth pulleys will achieve a higher top speed, & 14s are a nice balance between the two.

You can further adjust the performance by changing the Rear Drive wheel size. Changing from 8” to 9” or 10“ Tyres has a massive effect on the performance of the board. Check out the Pro Belt gearing chart to see estimated top speeds of different tyre & pulley combinations.

It is only possible to fit the TRAMPA 5 Spoke Hubs to Pro Drive Slave Pulleys. This means the 5-Spoke Superstar & Megastar wheels fit no problem. However it is only possible to run 8 – 10 inch tyres on the Pro Drives, due to low clearance around the housing tubs.

Enclosed within the Motor Mount tub is the Belt Tension Roller - a Bearing Mounted in Aluminium housing, that guides the belt into the optimum position/tension, to maintain the max amount of grip between the belt & the pulley.

Its possible a belt can snap for a variety of reasons. If you’re the kind of rider that likes to go off into the wilderness, then you should always ride with a couple of spare belts (when one snaps, chances are the other isn’t far off).  TRAMPA's Pro Belt Drive utilises two special cut-outs that ‘ejects’ broken belts from the housing – slimming the chances of snapped belts jamming up the Motor Pulley.

The best way to prevent a belt snap is to check over & replace the Pulleys & belts on a semi-regular basis - BEFORE they have chance to fail on you. Riding, accelerating & braking hard will wear out your belts & pulleys faster. We recommend you service your board every three rides, or after any particularly tough ride. Check the hardware is tight, the belts aren’t worn, & for any damage, particularly to the motor mounts/trucks. Ensure the tub is free from any dust/dirt. Servicing your board is important for keeping it running smoothly, as well as for your safety when riding.

Belt Tension Roller Housing for 20mm Belts

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

Made from T6 Heat-treated Aluminium, these Belt Tension Rollers are to designed to house a premium TRAMPA 608 BEARING, ensuring a smooth and consistent roll while tensioning the belts. Used with 20mm belts on OPEN BELT DRIVE Motor Mounts.

Sprung Steel C-CLIP used inside the Belt tension housings to secure 608 bearing

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

These C-Clips ensure the 608 bearing is secure within the Tension Rollers

Step SPACER used for positioning the 15mm Tension Roller on OBD Drive

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

These Spacer-Axles have two functions, correctly positioning the 20mm Tension Roller, as well as providing the housed 608 bearing a snug-fitting axle to spin freely on.

CUSTOM Motor protection Housing - TWIN MOTOR

HALF CAGE  

This filter has been designed for those who want to save as much weight as possible while still maintaining a level of protection against grit and dust. 
 
The filter mesh is 0.15 mm, this will only allow particulates that are small enough to pass through the air gap between motor magnets and the stator. 

Allowing for consistent cooling of the motor while reducing wear on the motor. 

•Available in 10 colours. 

•Aluminium and stainless construction. 

•Compatible with Trampa motor fan. 

Pairing with the MKII Delrin Motor Housings, these fans secure to the ends of 6376 Motors, creating a cooling airflow around the motors - reducing running motor temp, and increasing efficiency! 

Motor Fan - Connects to the end of the Motor & Spins to help maintain temps low

Pairing with the new MKII Delrin Motor Housings, these fans secure to the ends of 6376 Motors, creating a cooling airflow around the motors - reducing running motor temp, and increasing efficiency!

After many different designs and prototypes, this shape has proved the most efficient at creating an airflow that made a real difference to the motors’ performance.
Attaches to the end of motors using 5x M3x16mm Countersunk bolts.

PRO BELT TUB - Fits to both V2 16mm & V3 20mm Pro Belt Tub Covers

CNC’d from a solid block of T6 heat-treated Aluminium, the V3 PRO BELT MOTOR MOUNT TUB is built around keeping the drive train securely & accurately attached, while running as smoothly as possible. Paired with the specially designed CNC’d COVER, the completed tub keeps the elements outs, the gears & belts clean & dry, & the whole board running smoothly.

Attaching T6 Aluminium BASH GUARDS (left & right) ensures the Tub will survive every knock & bump the drive system is bound to receive on a ride.
Special cutouts on the sides of tub allow snapped belts to be ejected out & away from the drive train, preventing any jammed gears or wheel lock.

The Tub is perfectly symmetrical allowing it to slide onto left or right drive trains.

20mm PRO Belt Motor Mount TUB COVER Aluminium - V3

The Pro Belt Tub Cover is crucial to keeping your drive system free of dirt & debris. CNC’d from Premium Aluminium, giving it the perfect weight-to-strength ratio, the cover slots tightly over the Pro Belt Tub, perfectly sealing off the drive system.

PRO Belt Motor Mount Bash Guard - LEFT (REGULAR)

Made using hardened steel, the PRO BELT bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the left drivetrain.

PRO Belt Motor Mount Bash Guard - RIGHT (GOOFY)

Made using hardened steel, the PRO BELT bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the left drivetrain.

20mm PRO Belt MOTOR ADAPTOR

Housing a precision bearing for Motor Axle Support the PRO BELT DRIVE Motor Adaptor is used for attaching the motor securely to the drivetrain.
Precision CNC’d from hardened steel, the Motor Adaptor also allows for the use of PRO MOTOR HOUSING.

Mountainboard Motor Mount V-Ring TUB Seals - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

Mountainboard Motor Mount Truck Connector

Works with PRO BELT & SPUR GEAR Drives.
The Clamp housing slips over the axels of Precision CNC’d Vertigo Trucks, ensuring the drivetrain sits at the correct angle.
Working in conjunction with the Conical Clamp, when connected together the housing squeezes the clamp to the hanger, securely attaching the drivetrain to the trucks.

Precision CNC’d from T6 Heat-treated Aluminium.

Mountainboard Motor Mount Connector Conical Clamp

Works with PRO BELT & SPUR GEAR Drives.

Designed to work in conjunction & attach securely to Precision CNC’d VERTIGO trucks, the Conical Clamp slips tightly over the CNC’d square on the hanger of the trucks. When attached to the Clamp Housing, the Conical Clamp tightens around the hanger, ensuring secure & accurate Motor Mount attachment.

Precision CNC’d from T6 Heat-treated Aluminium.

Mountainboard Motor Mount Rubber pad for Conical Clamps - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

M4 x 10mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M3 x 18mm TORX Countersunk Head Bolt Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

BIGGEST Beast Box

M4 x 10mm TORX Dome/Button Headed Head Bolt Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M6 x 25mm Bolt - Fixes Trucks to HolyPro Decks - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

You’ll need 8 of the TRAMPA M6 x 25mm Marine Grade Stainless Steel Bolts & 8 of the TRAMPA M6 Stainless Steel Nylock Nuts to attach a pair of TRAMPA Skate Trucks to any TRAMPA Deck with Risers. You’ll also need a pair of 10mm ring spanners to tighten and loosen the Nuts & Bolts. Don’t forget to make sure you’re Nuts & Bolts are tight before you ride!

M5 x 20mm Regular Hex Head Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.