This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

12mm ATB Bearings with 9.525mm Bearing Reducer Sleeves for complete board

12mm ATB Bearings with 9.525mm Bearing Reducer Sleeves for complete board Mountainboard ABEC 5 Bearing 6001 2RS  (12 x 28 x 8mm) Removable sidewalls with Embossed Logo  Internal Bearing support spacer used with 8mm O-Ring on 9.525mm axles - 9.525 x 13.525 x 16.5mm 8mm Rubber O-Ring to fit in Bearings - 2mm Section x 8mm Bore NITRILE 70 Bearing conversion Spacer converts 12mm Bearings to fit 9.525mm Skate & Spring Truck TiTanium Axles
RRP
£25+

TRAMPA's own ABEC 7 STAINLESS STEEL Mountain / Kite-board bearings measure 12 x 28 x 8mm & will fit to 12mm axles. They are officially known as 6001 2RS Bearings. 6001 tells you the bearings size whilst 2RS means the bearing has 2 Rubber Seals. The Rubber Seals are inserted into the Outer raceway and in contact with the inner raceway, protecting the single row of lubricated ball bearings housed within the enclosed raceways from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing and maintaining maxium performance to the board & rider for as long as possible. The rubber coated sidewalls come in RED, BLUE & WHITE & embossed with the TRAMPA logo proving Top Quality!

These precision made TRAMPA Bearings are polished to an internationally recognised ABEC 7 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 7 polishing gives you a super smooth / super fast ride which prolonges top end roll speeds. Using Bearing Reducer Spacers you are able to make these Bearings fit to 9.52mm Skate Truck Axles or 10mm Scooter Axles no problem....

Internal Bearing support spacer used with 8mm O-Ring on 9.525mm axles - 9.525 x 13.525 x 16.5mm

This special Spacer measures 12mm (id) x 16mm (od) x 16.5mm (long) & is known as a Bearing Support Spacer. This Bearing Support Spacer fits between the Bearings, along side the 10mm O-Ring when fitting Bearings into a TRAMPA hub when mounting the wheel onto 12mm Axles.

Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stronger than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these 16.5mm spacers with the little 10mm O-Rings to prevent the rattles!! :-)

Mountainboard ABEC 5 Bearing 6001 2RS (12 x 28 x 8mm) Removable sidewalls with Embossed Logo

TRAMPA's very own Mountainboard Bearings measure 12 x 28 x 8mm & will fit in to all of the Hubs that TRAMPA has to offer. 

TRAMPA's precision made Bearings are polished to an internationally recognised ABEC 7 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 7 polishing gives you a super smooth, super fast ride with extendend free rolling & top end roll speeds.

The Bearings are designed to fit TRAMPA wheels directly to 12mm axles, however using Bearing Reducer Spacers you are able to make 6001-2RS Bearings fit to Mini Spring Truck or 12FIFTIES Truck which both use 9.525mm Axles... Using Bearing reducer sleeves on 9.525mm Axles gives a very neat flush finish to the assembly insuring your Bearings spin freely.

Mountainboard Bearings are officially known as 6001 2RS Bearings. 6001 tells you the bearings size whilst 2RS means the bearing has 2 Removable Sides. During production the rubber coated sidewalls are inserted into the Outer raceway & are in contact with the inner raceway, they protect the single row of lubricated ball bearings housed within the enclosed raceways from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing, maintaining maximum performance to the board & rider for as long as possible. The rubber coated sidewalls come in RED, BLUE & BLACK or CERAMIC GREEN & are embossed with the TRAMPA logo proving the Top Quality!

The sidewalls are removable so you can service your bearings... Servicing your bearings on a regular basis will ensure they run well for you. Remove your wheels & take out your bearings, then using a pointy object simply pick off one side of the bearings & pop them into some solvent or fuel to dissolve any grease, i use an old tooth brush to rub the bearings gently, hopefully removing all the dirt that gets in... I pop them into another pot of clean fuel & make sure the fuel stays clean so i know the bearings are clean.. Once clean i take them out, placing onto some tissue or similar to dry out, you can rub them or blow them dry with an air line which is fun as they mae a whizzy noise! once dry i add a few tiny drops of sewing machine oil & place the bearing, open side into the wheel leaving the 1 side that still has the rubber sidewall in the outer position protecting your bearings from the further ingress of dirt getting in.... Repeat according to your riding demands, more riding = more servicing if you want best performance!

Bearing conversion Spacer converts 12mm Bearings to fit 9.525mm Skate & Spring Truck TiTanium Axles

Use this handy little part to convert 12mm TRAMPA bearings to fit onto 9.525mm (3/8ths of an inch) Axles... You will commonly find 9.525mm axles on Skate Trucks or Trucks with Titanium Axles. Simply slip the Conversion Spacer into your 12mm Bearing & then insert the Wheel back onto the axle.... Couldnt be easier.... :-)

The pressed aluminium is accurately made so it fits snugly into your bearing and tightly slides over the axle. The flanged Rim allows the axle nut to tighten without squashing the bearing wall, ensuring free spinning maximum performance from your bearings at all times. The sleeve can be re used over and over again but remember to replace your bearings regularly....

8mm Rubber O-Ring to fit in Bearings - 2mm Section x 8mm Bore NITRILE 70

This O-Ring should be fitted when a 9.525 x 16.5mm Bearing Support Spacer is fitted into the wheel assembly when fitting a wheel onto 9.525mm Axles. It fits alongside the Bearing Support Spacer, in-between the Bearings. This O-Ring prevents rattles from the spacer against the bearings. Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stringer than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these little O-Rings!! :-)

TRAMPA's URBAN CARVEBOARDS use special Bearings measuring 9.525 x 28 x 8mm known as 16001 RS


Using TRAMPA's Bearing reducer sleeves you can make a regular 12mm ATB Bearing fit onto a smaller 9.525mm Axle! (Mini Spring Truck & Extra Wide Longboard Truck Axles) Once the bearing is fitted into the wheel, the very special precision made bearing reducer sleeve simply pushes tightly into the 12mm ATB Bearing allowing the previosly measuerd 12mm center hole be able to drop tightly onto 9.525mm axles. The Flange of the sleeve hugs the Bearing perfectly ensuring the most fantastic tight fit when the nut is eventually tightened down onto the wheel.

This kit supplies you with 8x 12mm ATB Bearings, 8x 9.525mm Bearing reducer Sleeves & Internal Bearing spacers to suit your application.

TRAMPA's very own Regular Mountain & Kiteboard bearings measure 12 x 28 x 8mm & will fit to all 12mm axles. They are officially known as 6001 2RS Bearings. 6001 tells you the bearings size whilst 2RS means the bearing has 2 Removable Seals. The Removable Rubber Seals are inserted into the Outer raceway whilst in contact with the inner raceway, protecting the single row of lubricated ball bearings housed within the enclosed raceways from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing and maintaining maxium performance to the board & rider for as long as possible. The rubber coated sidewalls are available in RED or BLUE & are embossed with the TRAMPA logo proving Top Quality!

TRAMPA's precision made steel bearings are polished to an internationally recognised ABEC 5 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 5 polishing gives you a super smooth / super fast ride which prolonges top end roll speeds. Using Bearing Reducer Spacers you are able to make these Bearings fit to 9.52mm Skate Truck Axles or 10mm Scooter Axles no problem....

In this Kit you get the following parts :
8x TRAMPA ABEC 5 6001 2RS All Terrain Board Bearings
4x 9.525mm Internal Bearing support spacer used with 8mm O-RIng on 9.525mm axles
4x 8mm Anti Vibration Rubber O-Ring for 9.525mm Axles - FITS BETWEEN BEARINGS
8x 9.525mm Axle - Bearing Conversion Spacer
------------------------------------------
Bearing Inner Diameter (Axle thickness) - 12mm
Bearing Outer Diameter (Hub Housing width) - 28mm
Bearing Tickness (Seating depth) - 8mm
Spacer Inner Diameter (Axle Thickness) - 9.525mm
Spacer Outer Diameter (Bearing Housing) - 13.525mm
Spacer Length (Space between Bearing) - 16.5mm
Weight: 200g
What colour Bearings do you want?
What colour Bearings do you want?

RED 12mm Mountainboard Bearings
RED 12mm Mountainboard Bearings

BLUE 12mm Mountainboard Bearings
BLUE 12mm Mountainboard Bearings

BLACK 12mm Mountainboard Bearings
BLACK 12mm Mountainboard Bearings

CERAMIC 12mm Mountainboard Bearings(+£25)
CERAMIC 12mm Mountainboard Bearings(+£25)

Its possible to fit Bearing Reducer Sleeves inside your Bearings to reduce your 12mm Bearings to fit onto either 9.525mm Axles (imperial 3/8ths) Axle or Metric 10mm Axles.... TRAMPA Axles are usually 12mm but some TRAMPA Axles are 9.525. Other brands use 10mm... Please measure then make your choice & purchase below...

What size Bearing reducer sleeves do you need??
What size Bearing reducer sleeves do you need??

fits 9.525mm Axle Bearing Conversion Spacer - TRAMPA Axles
fits 9.525mm Axle Bearing Conversion Spacer - TRAMPA Axles

fits 10mm Axle Bearing Conversion Spacer - Alternative applications
fits 10mm Axle Bearing Conversion Spacer - Alternative applications

Quantity required:
RRP £25  - 8x Bearings, Internal Support Spacers Rubber O-Ring's & Bearing Redeucer Spacers

Excluding VAT
HCC: 8714929000

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon