This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

TRAMPA CERAMIC 6001 2RS ATB Bearings with Reducer Sleeves for 9.525mm Axles - 12mm x 28mm axle GREEN Rubber Sealed Sidewalls x1 wheel

Si3N4 CERAMIC Mountainboard Bearing - Steel Ring with Nylon cage & 2x Removable Rubber shields 6001-2RS CERAMIC

Internal Bearing support spacer used with 8mm O-Ring on 9.525mm axles - 9.525 x 13.525 x 16.5mm

8mm Rubber O-Ring to fit in Bearings - 2mm Section x 8mm Bore NITRILE 70

Bearing conversion Spacer converts 12mm Bearings to fit 9.525mm Skate & Spring Truck TiTanium Axles

RRP
£15+

MANUALS
PARTS USED
DESCRIPTION
PURCHASE

1x Internal Bearing support spacer used with 8mm O-Ring on 9.525mm axles - 9.525 x 13.525 x 16.5mm
2x Si3N4 CERAMIC Mountainboard Bearing - Steel Ring with Nylon cage & 2x Removable Rubber shields 6001-2RS CERAMIC
2x Bearing conversion Spacer converts 12mm Bearings to fit 9.525mm Skate & Spring Truck TiTanium Axles
1x 8mm Rubber O-Ring to fit in Bearings - 2mm Section x 8mm Bore NITRILE 70

TRAMPA's own ABEC 7 STAINLESS STEEL Mountain / Kite-board bearings measure 12 x 28 x 8mm & will fit to 12mm axles. They are officially known as 6001 2RS Bearings. 6001 tells you the bearings size whilst 2RS means the bearing has 2 Rubber Seals. The Rubber Seals are inserted into the Outer raceway and in contact with the inner raceway, protecting the single row of lubricated ball bearings housed within the enclosed raceways from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing and maintaining maxium performance to the board & rider for as long as possible. The rubber coated sidewalls come in RED, BLUE & WHITE & embossed with the TRAMPA logo proving Top Quality!

These precision made TRAMPA Bearings are polished to an internationally recognised ABEC 7 quality. (ABEC 3-5 is recognised as the industry standard). ABEC 7 polishing gives you a super smooth / super fast ride which prolonges top end roll speeds. Using Bearing Reducer Spacers you are able to make these Bearings fit to 9.52mm Skate Truck Axles or 10mm Scooter Axles no problem....

Internal Bearing support spacer used with 8mm O-Ring on 9.525mm axles - 9.525 x 13.525 x 16.5mm

This special Spacer measures 12mm (id) x 16mm (od) x 16.5mm (long) & is known as a Bearing Support Spacer. This Bearing Support Spacer fits between the Bearings, along side the 10mm O-Ring when fitting Bearings into a TRAMPA hub when mounting the wheel onto 12mm Axles.

Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stronger than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these 16.5mm spacers with the little 10mm O-Rings to prevent the rattles!! :-)

Bearing conversion Spacer converts 12mm Bearings to fit 9.525mm Skate & Spring Truck TiTanium Axles

Use this handy little part to convert 12mm TRAMPA bearings to fit onto 9.525mm (3/8ths of an inch) Axles... You will commonly find 9.525mm axles on Skate Trucks or Trucks with Titanium Axles. Simply slip the Conversion Spacer into your 12mm Bearing & then insert the Wheel back onto the axle.... Couldnt be easier.... :-)

The pressed aluminium is accurately made so it fits snugly into your bearing and tightly slides over the axle. The flanged Rim allows the axle nut to tighten without squashing the bearing wall, ensuring free spinning maximum performance from your bearings at all times. The sleeve can be re used over and over again but remember to replace your bearings regularly....

8mm Rubber O-Ring to fit in Bearings - 2mm Section x 8mm Bore NITRILE 70

This O-Ring should be fitted when a 9.525 x 16.5mm Bearing Support Spacer is fitted into the wheel assembly when fitting a wheel onto 9.525mm Axles. It fits alongside the Bearing Support Spacer, in-between the Bearings. This O-Ring prevents rattles from the spacer against the bearings. Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stringer than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these little O-Rings!! :-)

TRAMPA's own ABEC 7 STAINLESS STEEL Mountain / Kite-board bearings measure 12 x 28 x 8mm & will fit to 12mm axles. They are officially known as s6001 RS Bearings. s6001 tells you the bearings size whilst RS means the bearing has Rubber Seals. The Rubber Seals are inserted into the Outer raceway and in contact with the inner raceway, protecting the single row of lubricated ball bearings housed within the enclosed raceways from the ingress of moisture, dust & dirt, retaining the pre-filled grease within the bearing and maintaining maxium performance to the board & rider for as long as possible. The Stainless steel bearings only come in BLACK, but still embossed with the TRAMPA logo proving Top Quality!

In this Kit you get the following parts :
2x 12x28x8mm CERAMIC Mountainboard Bearing Set
1x 9.525mm Internal Bearing support spacer used with 8mm O-RIng on 9.525mm axles
1x 8mm Anti Vibration Rubber O-Ring for 9.525mm Axles - FITS BETWEEN BEARINGS
2x 9.525mm Axle - Bearing Conversion Spacer
------------------------------------------
Bearing Inner Diameter (Axle thickness) - 28mm
Bearing Outer Diameter (Hub Housing width) - 12mm
Bearing Tickness (Seating depth) - 8mm
Spacer Inner Diameter (Axle Thickness) - 9.53mm
Spacer Outer Diameter (Bearing Housing) - 13.53mm
Spacer Length (Space between Bearing) - 16.5mm
Rubber O-Ring prevents unwanted rattles assembly - 8mm Oring to fit 9.525 or 10mm Axle
Bearing reducer spacers reducer the internal diameter of the bearing from 12mm Axles to fit to either 9.525mm Axles or 10mm Axles.
Weight: 42g

Its possible to fit Bearing Reducer Sleeves inside your Bearings to reduce your 12mm Bearings to fit onto either 9.525mm (imperial 3/8ths) Axle or Metric 10mm Axles....

Which size Bearing reducer sleeves do you want?

Please supply me with 9.525mm Bearing Reducer Sleeves

Please supply me with 10mm Bearing Reducer Sleeves

Quantity required:
We have enough parts to make

RRP £15 - 2x Bearings, Internal Support Space & Rubber O-Ring

Excluding VAT
HCC: 8714929000

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......