Home»Accessories»Scooter Accessory Packs»Rear wheel Assembly kits for Scooter»TITANIUM Rear Wheel Axlepin Assembly Kit

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

PRECISION Shim spacer - STAINLESS STEEL - Bridges tiny gaps on axles - 9.525 x 13.525 x 1mm

This tiny STEEL Shim Spacer is precision made to give maximum performance! It is used to hold the bearings in the perfect position & also to bridge tiny gaps on the axles, ensuring an accurate fit with NO rattles!

The Shim spacer slips onto the axle fitting either side of the Bearings when the wheel is being fitted onto 9.525mm Axles.

This tiny spacer positions the wheel perfectly on the axle, holding the Bearing in the best possible place to help achieve maximum spin rate for the wheel. Its little parts like these that suffer the most amount of abuse, especially when they are used in the harsh conditions that they are. Check from time to time they are in good order & possibly replacing them every now & then this good proactice will ensure your board stays in tip-top condition, always!

8mm TITANIUM King Pin - Half the weight of steel!

This M8 x 80mm TITANIUM Spring Truck Kingpin is used to connect the Hanger & the Baseplate on the TRAMPA ULTIMATE Trucks. By using an 8mm TITANIUM 8mm Kingpin we have managed to save loads of weight whilst retaining all the strength necessary for the job by using the high quality metals true to our word!

This M8 x 80mm Kingpin connects into an M6 Nut. You'll need a 4mm Allen key to hold the Kingpin & a 10mm spanner to tighten/loosen your M6 Kingpin Nut.

This Kingpin pushes through Plastic Bushings before being placed into position in the Truck System. The Plastic bushings allow the metal parts (Hanger & Baseplate) to move inside each other without allowing the metal parts to touch or wear out. The Plastic Bushings will wear out over time & will eventually perish & need replacing. SO, make sure your Bushings are always in good working order after riding riding or especially when upgrading your Kingpin, it might be time to replace them too due to the unavoidable wear & tear of moving mountainboard parts.

This Kingpin lives up to TRAMPA's incredibly high quality standards, but it's always handy to have a spare just in case you do break one out on a ride....

Axle Kingpin mounting bushings for TRAMPA Scooter

1mm Base Kingpin bushings for Spring Trucks. These bushings are housed within the Baseplate and Hanger. They allow the kingpin to move freely when the Truck is constructed. Made with different thickness base's to avoid any tolerance issues in production. Produced from the highest standard plastics available to ensure maximum Durabillity & to enable the best maximum performance in your Trucks. Check & replace these bushings from time to time to ensure your steering stays in top condition.    

12mm Bearing for TRAMPA All Terrain Mountain Boards 12x 28x 8mm with BLACK sidewalls & Embossed TRAMPA Logo ABEC 5 6001 2RS

8mm Rubber O-Ring to fit in Bearings - 2mm Section x 8mm Bore NITRILE 70

This O-Ring should be fitted when a 9.525 x 16.5mm Bearing Support Spacer is fitted into the wheel assembly when fitting a wheel onto 9.525mm Axles. It fits alongside the Bearing Support Spacer, in-between the Bearings. This O-Ring prevents rattles from the spacer against the bearings. Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stringer than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these little O-Rings!! :-)