Home»Trucks»ATB SKATE Trucks »9.525mm TITANIUM Axle Skate Trucks»Skate Truck 9.525mm Titanium axle

3/8ths Nut - Marine Grade Stainless steel Nylock HALF nut W3/8 - 24T UNF

This very special Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore reducing weight in the Truck also! A few Grams here & a few grams there soon adds up to quite alot & that makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area...

This very special 3/8^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W3/8_^ths - 24T - UNF. This Nut is used to hold the wheels onto the axles of the 9.525mm (3/8ths of Inch or otherwise referred to as 10mm) SKATE TRUCKS & also the Spring Trucks fitted with TITANIUM axles. This Nut is also used to hold the KINGPIN in position on all Skate Trucks. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 14mm or 9/16^ths of an Inch spanner to tighten the Nut onto the Axle or Kingpin, do not overtighten the nut, allow the wheel to spin freely but not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

 - Fits to 9.525mm (3/8ths) Axles & Skate Truck Kingpins

7/16ths Nut - Marine Grade Stainless steel Nylock Axle HALF nut (W7/16-20T UNF) - Fits to 12mm Axles

This very special 7/16_^ths of an inch Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut.. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore further reducing weight in the Truck! A few Grams here & a few grams there soon adds up & makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area, where a few grams makes all the difference...

This very special 3/8_^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W7/16 - 20T - UNF. This Nut is used to hold the wheels onto the axles of the Spring Trucks fitted with 12mm axles. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 16mm or 5/8th_^ths of an Inch spanner to tighten / loosen the Nut onto the Axle or Kingpin. Do not overtighten the nut & make sure the wheel can spin freely but does not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

Axle support Spacer fits TRAMPA Wheels onto 9.525 Skate Axles - 9.525mm x 13.525mm x 44mm - CNC'd

This 44mm Spacer is known as the 10mm Skate Truck Bearing Support Spacer as this spacer fits onto the axles of the 10mm Skate truck Axels. This spacer is used when mounting the TRAMPA wheel onto 9.525mm (10mm) or 3/8ths of an inch Skate Truck Axles. 

All of the TRAMPA spacers are produced as one long tube, The Tube will be T6 Heat Treated to give the ultimate strength. It is then High Quality Bead polished for best appearance and surface protection & then finally the tube is CNC cut to the exact spacer length for precision mounting. 

This Spacer measures 9.525mm (id) x 14mm (od) x 44mm (long) & is specifically designed to fit TRAMPA Wheels onto 10mm Skate Trucks Axels perfectly.

PRECISION Shim spacer - STAINLESS STEEL - Bridges tiny gaps on axles - 9.525 x 13.525 x 1mm

This tiny STEEL Shim Spacer is precision made to give maximum performance! It is used to hold the bearings in the perfect position & also to bridge tiny gaps on the axles, ensuring an accurate fit with NO rattles!

The Shim spacer slips onto the axle fitting either side of the Bearings when the wheel is being fitted onto 9.525mm Axles.

This tiny spacer positions the wheel perfectly on the axle, holding the Bearing in the best possible place to help achieve maximum spin rate for the wheel. Its little parts like these that suffer the most amount of abuse, especially when they are used in the harsh conditions that they are. Check from time to time they are in good order & possibly replacing them every now & then this good proactice will ensure your board stays in tip-top condition, always!

Skate Truck Baseplate - Trampa embossed, Bead polished & Powder coated - WHITE

TRAMPA's SKATE TRUCK Baseplate will only fit to TRAMPA Skate Truck Hangers. It is Embossed with the TRAMPA logo & presented in a Powder coated surface finish.

The Baseplate locks the KINGPIN in the housing space & stops it from spinning when tightened, allowing you tighten your Steering as tight as the Rubber can handle before splitting! Remember, over tightening your kingpin will eventually split the Bushing.

A Pivot cup is included with the purchase. For best performance check & if necessary replace your Pivot Cups regularly. Ensure the Bolts holding the Baseplate to the deck are tight before riding. Do not over tighten !

9.525mm TITANIUM axle Skate hanger - Powdercoated White & Colour option for Logo

TRAMPA's 9.52mm TITANIUM axle SKATE HANGER BODY is produced from FORGED ALUMINUM. Forging is used whenever Aluminum is required to perform to its maximum strength capability. During the forging process workers insert the TITANIUM Axle into the mould. The TITANIUM Axle is weight for weight stronger & lighter than the steel skate truck alternatives. Fixing the Axle to the hanger in this way gives the strongest possible connection between the 2 metals. The Hanger is BEAD POLISHED to give a smooth surface & POWDER COATED WHITE for best surface protection & is given a co-ordinating BLACK TRAMPA LOGO to Pimp its appearance!

TITANIUM SKATE TRUCKS are MEGA light weight. Saving weight will bring obvious benefits to freestyle Kiteboard riders aiming to go big, BUT Skate Trucks are not the strongest Trucks in the TRAMPA product range & we do not recommended they be used by large sized adult riders seeking huge freestyle moves as over time & especially after some hardcore mis-use, these Hangers can get bent & ultimately become un-usable! Top riders accept that the Skate trucks are not the strongest, and are generally quite happy to purchase replacements from time to time as their price to replace and light weight-ness is un-matched by any other style of steering system. So, if your going on a big riding session or road trip to a far off location, may we suggest you carry a spare one of these to cover emergencies... There is nothing worse than getting all the way to a remote location & then a stupid mistake stops your fun...

The TITANIUM Skate Hanger measures 15.5 Inches in total width. When the wheels are fitted to the Hanger, the board has a center wheel width of 13.5 Inches.

Skate Truck Kingpin Custom

The Trampa Hardened Steel Skate Truck Kingpin comes standard with Trampa Skate Trucks. This kingpin lives up to Trampas high standards, but it's always handy to have a spare just in case you do break one. Upgrade and save weight by fitting the Trampa Titanium Kingpin