This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

SILVER 9 inch Deep-Dish MEGASTARS Rim with BLACK Spokes & 9 Inch BLACK PRIMO STRIKER

SILVER 9 inch Deep-Dish MEGASTARS Rim with BLACK Spokes & 9 Inch BLACK PRIMO STRIKER 9 Inch DEEP DISH Off-Set MEGASTAR Rims SILVER - Place two on the rear of your Electric Mountainboard for extra Grip & Top Speed! BLACK Anodised Superstar Spoke - Extruded T6 Aluminum Heat treated & CNC Precision milled M4 x 40mm Socket Capped Bolt - Marine Grade Stainless steel with locking paste M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts Dupont Plastic Spoke support Spacer for the Superstar & Megastar hubs Internal Bearing support spacer used with 10mm O-RIng on 12mm axles - 12 x 16 x 16.5mm - LATHED PRIMO STRIKER 9 Inch Tyre - BLACK 10mm Rubber O-Ring to fit in Bearings - 2mm Section x 10mm Bore NITRILE 70 M4 x 16mm Socket Capped Head TORX Bolt ISO 4762 Marine Grade Stainless Steel 9 Inch Re-enforced Inner Tube made by INNOVA - 225x65mm
RRP
£75
exc tax

How to put a wheel on an Infinity or Vertigo truck

How to put a wheel on an Ultimate Truck

10mm Rubber O-Ring to fit in Bearings - 2mm Section x 10mm Bore NITRILE 70

This O-Ring should be fitted when a 12 x 16.5mm Bearing Support Spacer is fitted into the wheel assembly when fitting a wheel onto 12mm Axles.

It fits alongside the Bearing Support Spacer, in-between the Bearings. This O-Ring prevents rattles from the spacer against the bearings. Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stronger than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these little O-Rings!! :-)

M4 x 40mm Socket Capped Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA SUPERSTAR HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim of the SUPERSTAR HUB eventually screwing  into the M4 nut on the other side easly.

Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

USED FOR CONNECTING:  

SUPERSTAR HUBS       
MEGASTAR HUBS       
PHATLADS HUBS

M4 x 16mm Socket Capped Head TORX Bolt ISO 4762 Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

Black Plastic Anti Dust Valve Cap

Standard dust caps to fit all inner tubes. Keep the crud out of your valves!. There is nothing worse than not being able to inflate your tyres. So ensure your Anti dirt dust caps are fitted tight!. Also fits bi-cycle valves

9 Inch Re-enforced Inner Tube made by INNOVA - 225x65mm

INNOVA's Re-enforced 9 Inch inner tube measures 225mm x 65mm and will fit into all the of the 9 inch Tyres on the TRAMPA website. This 9 Inch Inner Tube will also fit into the tyres of other brands. Being made from slightly thicker rubber, this Inner Tube is slightly heavier than alternatives but the Inner Tube will handle much higher than recommended inflation rates... Therefore this INNOVA inner tube is ideal for heavier or pro riders seeking high inflation pressures...

This INNOVA Inner tube will fit into all known 9 inch tyres as well as most ATB Hubs on the market & it comes as expected with a "Plastic Anti Dust" Valve cap!

Punctures Suck! Its always possible to get a puncture in the environments we ride in, so always carry a spare if you don't want your day spoiling...

M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts

Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or  8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!

Internal Bearing support spacer used with 10mm O-RIng on 12mm axles - 12 x 16 x 16.5mm - LATHED

This special Spacer measures 12mm (id) x 16mm (od) x 16.5mm (long) & is known as a Bearing Support Spacer. This Bearing Support Spacer fits between the Bearings, along side the 10mm O-Ring when fitting Bearings into a TRAMPA hub when mounting the wheel onto 12mm Axles.

Over time, during the usage of your board, the bearings & spacers are put under a lot of force. Ultimately this force has to go somewhere... The Bearings use a Steel ring in their assembly where as the Bearing Support Spacers are made from Aluminum. Steel is much stronger than Aluminum & when forced against each the aluminum will loose out every time! This is what happens to your spacers between the bearings, the Bearings put force onto your spacers as a consequence over time the spacers shrink... With enough time its possible for an annoying rattle to start.... That's when you fit these 16.5mm spacers with the little 10mm O-Rings to prevent the rattles!! :-)

BLACK Anodised Superstar Original Spoke - Extruded T6 Aluminum Heat treated & CNC Precision milled

TRAMPA SPOKES fit all SUPERSTAR & MEGASTAR Hubs. TRAMPA's Spokes are produced using the finest 6061 'Aero-Grade' Aluminum, which to maximise strength & performance are produced with the use of an Extrusion Die, which means TRAMPA spokes are made in one continuous piece before being sliced like bread to the required thickness. Before being sliced the extruded profile is T6 Heat Treated making the resulting Alloy extremely strong

Once sliced, the Raw Spokes are bead polished which not only gives a top quality finish but also removes all & any sharp edges,  before then being sent away to CNC machine to precisely mill out the 28mm O.D. bearing housing. Finally the spokes are sent to the Anodisers to have the relevant striking colours added for top surface protection.

when checking your wheels and spokes also check your spoke support spacers, O-Rings & hardware are all in good condition & ensure all of your nuts & bolts are tight before you ride!

Dupont Plastic Spoke support Spacer for the Superstar & Megastar hubs

This is the TRAMPA SUPERSTAR Spoke Support Spacer. It is used to gain extra strength for the SUPERSTAR wheel design by adding support to the Aluminum Spokes when the wheel is being used under high inflated pressures...

Precision injection moulded, using original DuPont materials, this Spacer provides essential support for the Spokes in the Superstar hubs. There is a Deep Shelf on the Rim of the Spacer which pushes into the internal side of the Spoke, positioning the Spacer/spoke perfectly for assembly. The thick plastic ensures a very strong support platform maximising Bearing support & spin rate always....

Ensure all your nuts & bolts are tight before riding!!

PRIMO STRIKER 9 Inch Tyre - BLACK

PRIMO's 9 Inch STRIKER Tyre design brief is styled towards fast riding on hard packed dirt surfaces. It is made using a hard rubber compound with a wide Center Bead to help achieve & maintain maximum rolling speeds, whilst the close cut grip pattern around the sides of the tyre gives loads of grip on all kinds of changeable terrain's. Using Harder Rubber makes the STRIKER Tyre very fast whilst still hard-wearing, The PRIMO STRIKER is a great Tyre option for riding on any Solid surfaces from dusty dirt tracks to hard packed asphalt. 

Incorporated into the Rims of the tyre are 4 Inch wide Steel Bands. As the Rims are 4 Inch's wide this means that the 9 Inch PRIMO STRIKER tyre is too big to fit onto the regular TRAMPA hubs & therefore the 9 Inch Striker tyres will currently only fit onto the PRIMO 3-Spoke Composite Hubs. Larger wheels will travel better over bumpier or softer ground making them great for kiteboarding down the beach if the sand is soft. When the tyres are inflated to they measure 225mm in Diamter & 65mm wide.

Regular sized Threads (TPI) tie the 4 Inch Steel bands together giving the 9 Inch PRIMO STRIKER tyre the strength & structure to be inflated up to the recommended factory inflation pressures. The more you inflate your Tyres the faster you will roll! If you over inflate the Tyres it is possible they will explode which may cause you serious injury! The official maximum inflation pressure set by the factory for the 9 inch STRIKER Tyre is 50psi,  If you do decide to go beyond the max inflation pressure ensure your nuts & bolts are tight before inflating & deflate back to a regular pressure after use. 

Using TRAMPA's NEW & AMAZING 9 inch Deep-Dish MEGASTAR wheels, it is now possible to comfortably fit larger sized 9 inch wheels into the assembly any of the TRAMPA Belt Drives or Spur Gear Drives using 16 inch Mountain board Spring Trucks. 

Using 9 inch wheels which have been CNC Precision Milled from two solid blocks, milled with an offset bearing position, will significantly widen your wheel base making the board feel more stable & planted, whilst the additional width of the tires (9 inch Mud-Pluggers are 2.5 Inches wide where as 8 inch tyres are just 2 inches wide) increases the surface contact with the ground & as you can tell from the name of the Tyre which pretty much describes what its capable of, the extra 1/2 inch of tyre & the aggressive directional grip results in absolute heaps of extra grip comparing to the smaller 8 inch tyres, especially when riding off road in mddy conditions.

The increased tyre profile size of the well gripped sidewall will not only give you more Grip but also loads of extra Comfort when rolling over rough stuff & the increase of overall wheel size going from 8 inch to 9 inch will give you a natural Geared increase in Top Speed by approx 5%, making the new MEGASTAR hubs a must have piece of equipment for all serious of road electric mountain board riders out there...

It is possible to fit the 9 inch MEGASTAR WHEELS to any of TRAMPA's 66 Tooth Belt Driven Slave Pullies or 58/59 Tooth Spur Gear Drive Pulleys that would usually fit to the 8 inch Superstar wheels, So if you're looking for the latest all round upgrade, then this is the one for you!

The downside to using 9 inch wheels is the increase in weight... with all the increase in size they are bound to weigh more than the smaller wheels & rubber can weigh a lot... so to gain the extra grip that we talk about without adding to much extra weight we suggest that you only need to fit 2x of the 9 inch wheels on the rear drive wheels giving you the grip without all the weight of 4x wheels, so you only need just 2x 9 inch wheels to gain the extra Grip, speed & Comfort without too much extra weight...  You might be thinking, what 8 inch on the front and 9 inch on the back.... yep thats right guys.... You might be thinking but then its higher one end than the other, Yep, thats right.... the extra height at the rear almost forces you int a more aggressive stance, positioning you ready to take the huge forces in the acceleration... the stance is nice, the tyres are amazing.....!!!

Fits 76 Tooth Pulley for best gearing on Electric Boards - 

1x 9 Inch DEEP DISH Off-Set MEGASTAR Rims SILVER - Place two on the rear of your Electric Mountainboard for extra Grip & Top Speed!
1x Extruded T6 Aluminum BLACK Anodised Original Spoke - CNC Precision milled
5x M4 x 40mm Socket Capped Bolt - Marine Grade Stainless steel
5x M4 Nut - Marine Grade Stainless steel Nylock Nut
1x Super strength Dupont NYLON Spoke Support Spacer.
1x 16.5mm Internal Bearing support spacer used with 10mm O-RIng on 12mm axles
1x 10mm Anti Vibration Rubber O-Ring for 12mm Axles - FITS BETWEEN BEARINGS
1x 9 Inch PRIMO STRIKER Tyre - BLACK
2x M4 x 16mm Socket Capped TORX Bolt - Marine Grade Stainless Steel
1x 9 INCH Inner Tube - INNOVA
1x Black Plastic Anti Dust Valve Cap
Inflated Wheel Diameter 9in
Inflated Wheel Width 2.5in
Recommended Tyre Inflation 40 - 60psi
Fits in place of any 8 inch Wheel & fits to most of the Amazing Electric Mountainboards!
The offset bearing position allows a wider wheel base & extra space for your feet
9 Inch wheels will give you a Higher Top Speed, add more comfort to your ride over rough terrain, a lot more grip in the muddy stuff & make you look really really cool!! :-)
Weight: 819g
Please Select - What colour MEGASTAR Rim would you like?
Please Select - What colour MEGASTAR Rim would you like?

9 inch Deep-Dish MEGASTAR Rims - BLACK
9 inch Deep-Dish MEGASTAR Rims - BLACK

9 inch Deep-Dish MEGASTAR Rims - BLUE
9 inch Deep-Dish MEGASTAR Rims - BLUE

9 inch Deep-Dish MEGASTAR Rims - BRONZE
9 inch Deep-Dish MEGASTAR Rims - BRONZE

9 inch Deep-Dish MEGASTAR Rims - GOLD
9 inch Deep-Dish MEGASTAR Rims - GOLD

9 inch Deep-Dish MEGASTAR Rims - GREEN
9 inch Deep-Dish MEGASTAR Rims - GREEN

9 inch Deep-Dish MEGASTAR Rims - GUNMETAL
9 inch Deep-Dish MEGASTAR Rims - GUNMETAL

9 inch Deep-Dish MEGASTAR Rims - PINK
9 inch Deep-Dish MEGASTAR Rims - PINK

9 inch Deep-Dish MEGASTAR Rims - PURPLE
9 inch Deep-Dish MEGASTAR Rims - PURPLE

9 inch Deep-Dish MEGASTAR Rims - RED
9 inch Deep-Dish MEGASTAR Rims - RED

9 inch Deep-Dish MEGASTAR Rims - SILVER
9 inch Deep-Dish MEGASTAR Rims - SILVER

Quantity required:
We have enough parts to make…  
RRP £75 - per wheel

Excluding VAT

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon