Home»Accessories»WHEELS Accessories & TYRE kits»Bearing Sets»R608 8mm Axle LONGBOARD Wheel Bearings»R608 8mm Axle Longboard or Skateboard ABEC 7 Bearings with Spacers 8x 8x22x7mm 608

8 x 12 x 10.3mm Carbon Steel Internal Bearing Support Longboard wheel bearings Spacer

This spacer will fit onto an 8mm axle, it has a 12mm outer diameter & is 10.3mm Long in length. Its job is to fit between the bearings of longboard wheels to support the load through the bearing centre, its strongest point.

The Carbon Steel Longboard wheel Spacer is .3mm oversized to allow for shrinkage gained from natural usage over time which ultimately prevents ratttle & maintains best performance to the user for as long as possible. From time to time it is good practice for you to exchange your spacers to ensure maximum performance at all times.

PRECISION Shim spacer - Bridges the tiny gaps between bearings on 8mm axles - 8 x 14 x 1mm

This little STAINLESS STEEL Shim Spacer is precision made. It ensures maximum performance to the wheels & nuts. Made from Marine grade stainless steel it will not rust on you! It is used to hold the bearings in the perfect position & also to bridge tiny gaps on the axles, ensuring an accurate fit with NO rattles! The Shim spacer slips onto the Axle, fitting either side of the Bearings when the wheel is being fitted onto 12mm axles. This tiny spacer positions the wheel perfectly on the axle, holding the Bearing in the best possible place to help achieve maximum spin rate for the bearing & wheel. Its little parts like these that suffer the most amount of abuse, especially when they are used in the harsh conditions that they are. Check from time to time they are in good order & possibly replacing them every now & then this good practice will ensure your board stays in tip-top condition, always!

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.