This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

MKII 12A BIGGER BEAST Box fits 1x VESC 6 & 2x 6s 12A cells to give approx 15 miles range

MKII 12A BIGGER BEAST Box fits 1x VESC 6 & 2x 6s 12A cells to give approx 15 miles range MkII BIGGER URBAN BEAST Box Panels - fits 2x 6s 12A cells & HD-60Twin or 1x VESC6 Panel VESC 6 Mounting Panel for MkII BIGGER BEAST Box - SINGLE MOTOR M4 x 80mm Aluminium Threaded Spacer Nut Used for assembling the BEAST Battery Boxes M4 x 10mm TORX Countersunk bolt Marine Grade Stainless Steel M4 x 35mm TORX Countersunk Bolt Marine Grade Stainless Steel M4 x 25mmTORX Countersunk Bolt  Marine Grade Stainless Steel M6 x 30mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste 5mm ROUND BLIND Rubber Grommet for 5mm TRAMPA Silicone Cable 5mm Cable Entry OPEN Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes OVAL Rubber BLIND Grommet Cable Entry Hole - Fits in Monster Box side panels for water proof assistance & Neat Cabeling QUALA-T Power Switch Kit - Power Switch, 16mm Fixing Nut & Cable Harness. Blue, Red or White 5v LED M4 x 10mm TORX Dome/Button Headed Head Bolt Marine Grade Stainless Steel TORX M4 Dome Head Nut - Stainless Steel M4 Washer Marine Grade Stainless steel 165mm x 4.8mm Zip Tie M4x 12mm Anodised Aluminium THUMB SCREW colour co ordinatingly secures the Inspection Pit lid on to the Battery Box M4 Stainless Steel Square nut - secures the inspection pit LID to the Box its fitting to
RRP
£150+

DESCRIPTION


The MKII 'BIGGER BEAST BOX' is the perfect choice for sleek-looking & high range, twin-motor boards. Mounting above the rear truck & able to fit 1x VESC 6 or VESC HD-60T speed controller alongside 2x 12,000mAh Li-Po Batteries in a sleek, weather-&-knock-proof enclosure creates a neat & finished looking board with all the electrical components gathered, with minimal wires or connections on show.  

Able to fit onto any TRAMPA board with Spring Trucks, this BEAST BOX is made from 2mm thick 3k Twill Carbon Fiber. Precision CNC machined & internally grooved to give perfectly fitted joins, the Beast Box is pretty much water proof. Heat shrinking your joins & adding a touch of silicon at the end of the assembly will for sure seal the box to be tight from water!

The beast box comes with a top mounted power button - meaning no more fiddling with loop keys - just a simple press & you're good to go! Also found on the top of the box is an 'inspection pit', a water-tight compartment that allows easy access to the charge port & balance leads.

High-quality cable kits available for using VESC 6 or VESC HD-60T Speed controllers.

Assembling the box has been described as “fiddly but fun”. It’s a tight fit when using the biggest batteries for each box, so keep that in mind while assembling. The less room the batteries have to bounce around inside the box the better - especially over rough terrain!

Stainless steel Countersunk bolts harmoniously connect into both the base & the lid of the box, screwing neatly & tightly into HEX spacers... as the lid is tightened down, you get a satisfying click of confidence that everything has dropped into place perfectly as the panels slips into the groove and the gaps are no longer visible!


TRAMPA’s Beast Boxes come in three different sizes;

STANDARD - Fits 2x 6s 6200mAh Li-Po Batteries

BIGGER - fits 2x 6s 12,000mAh Li-Po Batteries

BIGGEST - fits 2x 6s 16,000mAh Li-Po Batteries.

Boards with single motors could go for any of the Beast Boxes - dependent on the desired range / weight of the finished board.

Able to fit onto any TRAMPA board with Spring Trucks, this BEAST BOX is made from 2mm thick 3k Twill Carbon Fiber. Precision CNC machined & internally grooved to give perfectly fitted joins, the Beast Box is pretty much water proof. Heat shrinking your joins & adding a touch of silicon at the end of the assembly will for sure seal the box to be tight from water!

The beast box comes with a top mounted power button - meaning no more fiddling with loop keys - just a simple press & you're good to go!

Assembling the box has been described as “fiddly but fun”. It’s a tight fit when using the biggest batteries for each box, so keep that in mind while assembling. The less room the batteries have to bounce around inside the box the better - especially over rough terrain!

Stainless steel Countersunk bolts harmoniously connect into both the base & the lid of the box, screwing neatly & tightly into HEX spacers... as the lid is tightened down, you get a satisfying click of confidence that everything has dropped into place perfectly as the panels slips into the groove and the gaps are no longer visible!


Everything fits Internally with TWIN VESC HD

MkII BIGGER URBAN BEAST Box Panels - fits 2x 6s 12A cells & HD-60Twin or 1x VESC6 Panel

TRAMPA’s Beast Boxes come in three different sizes;

STANDARD - fitting up to 6200mAH Batteries

BIGGER - fitting up to 12,000mAH Batteries

BIGGEST - fitting up to 16,000mAH Batteries.

Boards with single motors could go for any of the Beast Boxes - dependant on the desired range / weight of the finished board.

Boards with TWIN Motors will need to go for the BIGGEST BOX, in order to accommodate room for the extra VESC that needs to sit inside.

Able to fit onto any TRAMPA board with Spring Trucks, BEAST BOXES made from 2mm thick 3k Twill Carbon Fiber & are precision CNC machined & internally grooved to give perfectly fitted joins, making the Beast Box pretty much water proof. Heat shrinking your joins & adding a touch of silicon at the end of the assembly will for sure seal the box to be tight from water!

The beast box comes with a top mounted LCD Battery Indicator, so guessing range is no longer an issue!

Assembling the box has been described as “fiddly but fun”. It’s a tight fit when using the biggest batteries for each box, so keep that in mind while assembling. The less room the batteries have to bounce around inside the box the better - especially over rougher terrain!

Stainless steel Countersunk bolts harmoniously connect into both the base & the lid of the box, screwing neatly & tightly into HEX spacers... as the lid is tightened down, you'll get a satisfying click of confidence that everything has dropped into place perfectly, as the panels slips into the groove and the gaps are no longer visible!

Battery Box Width - 
Battery Box Length - 
Averything fits Internally!

 

VESC 6 Mounting Panel for MkII BIGGER BEAST Box - SINGLE MOTOR

TRAMPA’s Beast Boxes come in three different sizes;

STANDARD - fitting up to 6200mAH Batteries

BIGGER - fitting up to 12,000mAH Batteries

BIGGEST - fitting up to 16,000mAH Batteries.

Boards with single motors could go for any of the Beast Boxes - dependant on the desired range / weight of the finished board.

Boards with TWIN Motors will need to go for the BIGGEST BOX, in order to accommodate room for the extra VESC that needs to sit inside.

Able to fit onto any TRAMPA board with Spring Trucks, BEAST BOXES made from 2mm thick 3k Twill Carbon Fiber & are precision CNC machined & internally grooved to give perfectly fitted joins, making the Beast Box pretty much water proof. Heat shrinking your joins & adding a touch of silicon at the end of the assembly will for sure seal the box to be tight from water!

The beast box comes with a top mounted LCD Battery Indicator, so guessing range is no longer an issue!

Assembling the box has been described as “fiddly but fun”. It’s a tight fit when using the biggest batteries for each box, so keep that in mind while assembling. The less room the batteries have to bounce around inside the box the better - especially over rougher terrain!

Stainless steel Countersunk bolts harmoniously connect into both the base & the lid of the box, screwing neatly & tightly into HEX spacers... as the lid is tightened down, you'll get a satisfying click of confidence that everything has dropped into place perfectly, as the panels slips into the groove and the gaps are no longer visible!

Battery Box Width - 110m
Battery Box Length - 200mm
Averything fits Internally!

 

Cable Harness for wiring Power Switches to VESCs

Harness allows connection between VESC 6 MkIII or newer and on/off switch.

TRAMPA Switch with 5V LED QUALA-T logo & 16mm Stainless Steel Fixing Nut

The TRAMPA 'QUALA-T" stamped Power Switch is a sexy little switch & to co-ordinate with the huge array of anodised & painted colours that TRAMPA offers to tie into all the other kit we offer is available in 6 different colours - RED, BLUE, YELLOW, GREEN, WHITE, PINKY/PURPLE

Which means no more loop keys!
All TRAMPA Mountainoboards Boards fitted with VESC 6 MKIII & any later models can now be fitted with power buttons for easy powering on/off and a much sleeker looking board!

You will need a Power Switch Cable harnesses to plug in

The QUALA-T Switch is Non-latching & limited to a Max voltage of 5v 

5mm ROUND BLIND Rubber Grommet for 5mm TRAMPA Silicone Cable

This 5mm Round Blind Grommet is used to seal off un used Motor Cable Entry Holes in the MONSTER Box, BEAST Box & Underboard BATTERY Box.

The 5mm Round Blind Grommet should also be fitted into all Battery Boxes which are using the Motor Cable entry holes as passing the cables through the 'OPEN' Grommet seals the hole best as possible & protects from the ingress of moisture & dust. 

To open the grommet to pass a cable through simply use a sharp Knife to press against the pre pressed slicing line & slice open the Rubber Membrane to allow you to push your cables through. Easy!

 

5mm Cable Entry OPEN Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes

5mm Cable Entry Open Rubber Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes in Monster Box side panels for water proof assistance & Neat Cabling

OVAL Rubber BLIND Grommet Cable Entry Hole - Fits in Monster Box side panels for water proof assistance & Neat Cabeling

This OVAL Rubber BLIND Grommet Cable Entry Blank is used to seal of Entry Holes in MONSTER Box, BEAST Box & Underboard Battery Tray which fits on the ORRSOM longboard. Simply push the Oval Grommet into position & your entery holes is sealed from moisture & dust.

If you need to push a cable through, use a sharp knife and carefully slice through the rubber membrane.

165mm x 4.8mm Zip Tie

Zip ties can be used to secure cables and other items wherever needed on your board.

M6 x 30mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

 

- 6-8s Battery Box

- 8-10s Battery Box

-Beast Boxes

 

 

M4 x 10mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 35mm TORX Countersunk Bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 25mmTORX Countersunk Bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 80mm Aluminium Threaded Spacer Nut Used for assembling the BEAST Battery Boxes

Used for assembling the BEAST BATTERY BOX.

x7 Required per box

TECHNICAL


The MKII 'BIGGER BEAST BOX' is the perfect choice for sleek-looking & high range, twin-motor boards. Mounting above the rear truck & able to fit 1x VESC 6 or VESC HD-60T speed controller alongside 2x 12,000mAh Li-Po Batteries in a sleek, weather-&-knock-proof enclosure creates a neat & finished looking board with all the electrical components gathered, with minimal wires or connections on show.  

Able to fit onto any TRAMPA board with Spring Trucks, this BEAST BOX is made from 2mm thick 3k Twill Carbon Fiber. Precision CNC machined & internally grooved to give perfectly fitted joins, the Beast Box is pretty much water proof. Heat shrinking your joins & adding a touch of silicon at the end of the assembly will for sure seal the box to be tight from water!

The beast box comes with a top mounted power button - meaning no more fiddling with loop keys - just a simple press & you're good to go! Also found on the top of the box is an 'inspection pit', a water-tight compartment that allows easy access to the charge port & balance leads.

High-quality cable kits available for using VESC 6 or VESC HD-60T Speed controllers.

Assembling the box has been described as “fiddly but fun”. It’s a tight fit when using the biggest batteries for each box, so keep that in mind while assembling. The less room the batteries have to bounce around inside the box the better - especially over rough terrain!

Stainless steel Countersunk bolts harmoniously connect into both the base & the lid of the box, screwing neatly & tightly into HEX spacers... as the lid is tightened down, you get a satisfying click of confidence that everything has dropped into place perfectly as the panels slips into the groove and the gaps are no longer visible!


TRAMPA’s Beast Boxes come in three different sizes;

STANDARD - Fits 2x 6s 6200mAh Li-Po Batteries

BIGGER - fits 2x 6s 12,000mAh Li-Po Batteries

BIGGEST - fits 2x 6s 16,000mAh Li-Po Batteries.

Boards with single motors could go for any of the Beast Boxes - dependent on the desired range / weight of the finished board.

Able to fit onto any TRAMPA board with Spring Trucks, this BEAST BOX is made from 2mm thick 3k Twill Carbon Fiber. Precision CNC machined & internally grooved to give perfectly fitted joins, the Beast Box is pretty much water proof. Heat shrinking your joins & adding a touch of silicon at the end of the assembly will for sure seal the box to be tight from water!

The beast box comes with a top mounted power button - meaning no more fiddling with loop keys - just a simple press & you're good to go!

Assembling the box has been described as “fiddly but fun”. It’s a tight fit when using the biggest batteries for each box, so keep that in mind while assembling. The less room the batteries have to bounce around inside the box the better - especially over rough terrain!

Stainless steel Countersunk bolts harmoniously connect into both the base & the lid of the box, screwing neatly & tightly into HEX spacers... as the lid is tightened down, you get a satisfying click of confidence that everything has dropped into place perfectly as the panels slips into the groove and the gaps are no longer visible!


Everything fits Internally with TWIN VESC HD

In this Kit you get the following parts

1x All panels required to make the 12A BEAST Box Excluding VESC PANEL
1x VESC Mounting Panel
7x M4 x 80mm Threaded HEX SPACER or Stand off's
7x M4 x 10mm Bottom of Box Countersunk TORX Bolts
6x M4 x 25 Top of the Box Countersunk TORX Bolts
1x M4 x 35 Top of the Box Countersunk TORX Bolts
2x M6 x 30 Box to decks Countersunk ALLENKEY bolts
2x 5mm Small Round BLIND Rubber Grommets
6x 5mm Small Round OPEN Rubber Grommets
2x Large OVAL Blind Rubber grommets
1x Power Switch
1x Power Switch Cable Harness
2x M4 x 16 Socket Cap Head Stainless Steel Bolt for Cable Tidy
2x M4 Dome Head Stainless Steel Nut for Cable Tidy
2x M4 Washer to fit with the Cable Tidy
4x 165mm Zip ties for securing cables on cable tidy
1x Easy Twist Stainless Steel Thumb Screw for the inspection Pit
1x M4 Stainless Steel Square Nut for securing the Inspection lid
Weight: 722g
What colour Power Switch do you want in your 12A BEAST Box?
What colour Power Switch do you want in your 12A BEAST Box?

I'd like a BLUE Power Switch on my 12A BEAST Box
I'd like a BLUE Power Switch on my 12A BEAST Box

I'd like a GREEN Power Switch on my 12A BEAST Box
I'd like a GREEN Power Switch on my 12A BEAST Box

I'd like a PINK Power Switch on my 12A BEAST Box
I'd like a PINK Power Switch on my 12A BEAST Box

I'd like a RED Power Switch on my 12A BEAST Box
I'd like a RED Power Switch on my 12A BEAST Box

I'd like a WHITE Power Switch on my 12A BEAST Box
I'd like a WHITE Power Switch on my 12A BEAST Box

I'd like a YELLOW Power Switch on my 12A BEAST Box
I'd like a YELLOW Power Switch on my 12A BEAST Box

What colour 80mm HEX Spacers would you like for your BEAST Box?
What colour 80mm HEX Spacers would you like for your BEAST Box?

BLACK 75mm BEAST Box HEX Spacers
BLACK 75mm BEAST Box HEX Spacers

BLUE 75mm BEAST Box HEX Spacers
BLUE 75mm BEAST Box HEX Spacers

BRONZE 80mm BEAST Box HEX Spacers
BRONZE 80mm BEAST Box HEX Spacers

GOLD 80mm BEAST Box HEX Spacers
GOLD 80mm BEAST Box HEX Spacers

GREEN 80mm BEAST Box HEX Spacers
GREEN 80mm BEAST Box HEX Spacers

GUNMETAL 80mm BEAST Box HEX Spacers
GUNMETAL 80mm BEAST Box HEX Spacers

PINK 80mm BEAST Box HEX Spacers
PINK 80mm BEAST Box HEX Spacers

PURPLE 80mm BEAST Box HEX Spacers
PURPLE 80mm BEAST Box HEX Spacers

RED 75mm BEAST Box HEX Spacers
RED 75mm BEAST Box HEX Spacers

SILVER 75mm BEAST Box HEX Spacers
SILVER 75mm BEAST Box HEX Spacers

Would you like to add a VESC 6 to your 12A BEAST box?
Would you like to add a VESC 6 to your 12A BEAST box?

Yes please supply me with 1x VESC 6 - SINGLE MOTOR (+£180)
Yes please supply me with 1x VESC 6 - SINGLE MOTOR (+£180)

No VESC wanted Thanks

Quantity required:
We have enough parts to make…  
RRP £150 - for the complete set

Excluding VAT
HCC: 7019650019

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon