Home»Electrical Accessories»Motor Covers, Filters, Fans & Fittings Kits»FULL CAGE Motor Protection with Fans»FULL CAGE Motor protection FILTER & Fan - TWIN

FULL CAGE Motor protection - Fits Motor Fan & Coloured Stainless Steel Filters

TRAMPA's FULL cover Motor Protection CAGE has been skillfully CNC Machined from a solid Rod of very strong DELRIN Plastic (original DUPONT material) & is one very strong piece. 

This Full Cage you see is the second generation of Full motor protection cages, the 2nd gen is upgraded with a Hollow end & enables a MOTOR COOLING FAN to fit perfectly tight within the angled sides of the Super Strong Delrin housing & as the motors spin faster & faster this draws more & more air through the motor housing bringing much sort after cooling in many instances. 

The Full cover Cage should be lined with any 1 of 10 different colour painted Stainless Steel Mesh's. The MESH gauge is so small (0.15mm) that any tiny particles that can pass through the filter are smaller than the space of that in the air gap between the Magnets & Stator in the motor, so any tiny particles small enough to pass effectively pass straight though your motor extending operating life by reducing wear on the motor. 

The Motor Cooling Fan can fit to any 63mm TRAMPA motor when fitted to the HALF CAGE Motor filters (Check there is space in the motor mounts) & the fan fits perfectly with the Full Cage with the 6376 Motors. 6386 Motors too long, 6364 not long enough...

The Full cover Cage fits to all of TRAMPA's Mountain Board Motor Mounts. When fitting to Spur Gear Drive Mounts you should use 6x very special M3.5x12mm TORX Pan Head EJOT plastic thread cutting Bolts which cut its own thread as its turned & bites into the Delrin plastic for the best secure fit, or if you are screwing into any of the BELT drive motor mounts, Pro Belt Drive or Open Belt Drive, you should use the equally special 6x M3x10 Countersunk TORX EJOT Bolts to get the very best fit!

MkII FULL Motor Protection - Stainless Steel Mesh FILTER

The Full cover Motor Cage should be lined with any 1 of 10 different colour painted Stainless Steel Mesh's. The MESH gauge is so small (0.15mm) that any tiny particles that can pass through the filter are smaller than the space of that in the air gap between the Magnets & Stator in the motor, so any tiny particles small enough to pass effectively pass straight though your motor extending operating life by reducing wear on the motor. 

The Motor Cooling Fan can fit to any 63mm TRAMPA motor when fitted to the HALF CAGE Motor filters (Check there is space in the motor mounts) & the fan fits perfectly with the Full Cage with the 6376 Motors. 6386 Motors too long, 6364 not long enough...

The Full cover Cage fits to all of TRAMPA's Mountain Board Motor Mounts. When fitting to Spur Gear Drive Mounts you should use 6x very special M3.5x12mm TORX Pan Head EJOT plastic thread cutting Bolts which cut its own thread as its turned & bites into the Delrin plastic for the best secure fit, or if you are screwing into any of the BELT drive motor mounts, Pro Belt Drive or Open Belt Drive, you should use the equally special 6x M3x10 Countersunk TORX EJOT Bolts to get the very best fit

TRAMPA's FULL cover Motor Protection CAGE has been skillfully CNC Machined from a solid Rod of very strong DELRIN Plastic (original DUPONT material) & is one very strong piece. 

This Full Cage you see is the second generation of Full motor protection cages, the 2nd gen is upgraded with a Hollow end & enables a MOTOR COOLING FAN to fit perfectly tight within the angled sides of the Super Strong Delrin housing & as the motors spin faster & faster this draws more & more air through the motor housing bringing much sort after cooling in many instances. 

Motor Fan - Connects to the end of the Motor & Spins to help maintain temps low

Pairing with the new MKII Delrin Motor Housings, these fans secure to the ends of 6376 Motors, creating a cooling airflow around the motors - reducing running motor temp, and increasing efficiency!

After many different designs and prototypes, this shape has proved the most efficient at creating an airflow that made a real difference to the motors’ performance.
Attaches to the end of motors using 5x M3x16mm Countersunk bolts.

M3 x 18mm TORX Countersunk Head Bolt Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

BIGGEST Beast Box