This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

MkII FULL Motor Protection Cover & MESH FILTER - SILVER

MkII FULL Motor Protection Cover & MESH FILTER - SILVER
RRP
£10+

The Full cover Motor Cage should be lined with any 1 of 10 different colour painted Stainless Steel Mesh's. The MESH gauge is so small (0.15mm) that any tiny particles that can pass through the filter are smaller than the space of that in the air gap between the Magnets & Stator in the motor, so any tiny particles small enough to pass effectively pass straight though your motor extending operating life by reducing wear on the motor. 

The Motor Cooling Fan can fit to any 63mm TRAMPA motor when fitted to the HALF CAGE Motor filters (Check there is space in the motor mounts) & the fan fits perfectly with the Full Cage with the 6376 Motors. 6386 Motors too long, 6364 not long enough...

The Full cover Cage fits to all of TRAMPA's Mountain Board Motor Mounts. When fitting to Spur Gear Drive Mounts you should use 6x very special M3.5x12mm TORX Pan Head EJOT plastic thread cutting Bolts which cut its own thread as its turned & bites into the Delrin plastic for the best secure fit, or if you are screwing into any of the BELT drive motor mounts, Pro Belt Drive or Open Belt Drive, you should use the equally special 6x M3x10 Countersunk TORX EJOT Bolts to get the very best fit

TRAMPA's FULL cover Motor Protection CAGE has been skillfully CNC Machined from a solid Rod of very strong DELRIN Plastic (original DUPONT material) & is one very strong piece. 

This Full Cage you see is the second generation of Full motor protection cages, the 2nd gen is upgraded with a Hollow end & enables a MOTOR COOLING FAN to fit perfectly tight within the angled sides of the Super Strong Delrin housing & as the motors spin faster & faster this draws more & more air through the motor housing bringing much sort after cooling in many instances. 

The Full cover Motor Cage should be lined with any 1 of 10 different colour painted Stainless Steel Mesh's. The MESH gauge is so small (0.15mm) that any tiny particles that can pass through the filter are smaller than the space of that in the air gap between the Magnets & Stator in the motor, so any tiny particles small enough to pass effectively pass straight though your motor extending operating life by reducing wear on the motor. 

The Motor Cooling Fan can fit to any 63mm TRAMPA motor when fitted to the HALF CAGE Motor filters (Check there is space in the motor mounts) & the fan fits perfectly with the Full Cage with the 6376 Motors. 6386 Motors too long, 6364 not long enough...

The Full cover Cage fits to all of TRAMPA's Mountain Board Motor Mounts. When fitting to Spur Gear Drive Mounts you should use 6x very special M3.5x12mm TORX Pan Head EJOT plastic thread cutting Bolts which cut its own thread as its turned & bites into the Delrin plastic for the best secure fit, or if you are screwing into any of the BELT drive motor mounts, Pro Belt Drive or Open Belt Drive, you should use the equally special 6x M3x10 Countersunk TORX EJOT Bolts to get the very best fit

TRAMPA's FULL cover Motor Protection CAGE has been skillfully CNC Machined from a solid Rod of very strong DELRIN Plastic (original DUPONT material) & is one very strong piece. 

This Full Cage you see is the second generation of Full motor protection cages, the 2nd gen is upgraded with a Hollow end & enables a MOTOR COOLING FAN to fit perfectly tight within the angled sides of the Super Strong Delrin housing & as the motors spin faster & faster this draws more & more air through the motor housing bringing much sort after cooling in many instances. 


Weight: 13g
HCC: 73262000
This product cannot be purchased on its own.

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon