Home»ELECTRIC COMPONENTS»Battery Boxes»Mk II MASSIVE MONSTER Box - 21700 35Ah»2WD Mk II MASSIVE MONSTER Box

Power Switch Cable Harness 16mm

Harness allows connection between VESC 6 MkIII or newer and on/off switch.

TRAMPA Switch with 5V LED QUALA-T logo & 16mm Stainless Steel Fixing Nut

The TRAMPA 'QUALA-T" stamped Power Switch is a sexy little switch & to co-ordinate with the huge array of anodised & painted colours that TRAMPA offers to tie into all the other kit we offer is available in 6 different colours - RED, BLUE, YELLOW, GREEN, WHITE, PINKY/PURPLE

Which means no more loop keys!
All TRAMPA Mountainoboards Boards fitted with VESC 6 MKIII & any later models can now be fitted with power buttons for easy powering on/off and a much sleeker looking board!

You will need a Power Switch Cable harnesses to plug in

The QUALA-T Switch is Non-latching & limited to a Max voltage of 5v 

5mm Cable Entry OPEN Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes

5mm Cable Entry Open Rubber Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes in Monster Box side panels for water proof assistance & Neat Cabling

OVAL Rubber BLIND Grommet Cable Entry Hole - Fits in Monster Box side panels for water proof assistance & Neat Cabeling

This OVAL Rubber BLIND Grommet Cable Entry Blank is used to seal of Entry Holes in MONSTER Box, BEAST Box & Underboard Battery Tray which fits on the ORRSOM longboard. Simply push the Oval Grommet into position & your entery holes is sealed from moisture & dust.

If you need to push a cable through, use a sharp knife and carefully slice through the rubber membrane.

5mm ROUND BLIND Rubber Grommet for 5mm TRAMPA Silicone Cable

This 5mm Round Blind Grommet is used to seal off un used Motor Cable Entry Holes in the MONSTER Box, BEAST Box & Underboard BATTERY Box.

The 5mm Round Blind Grommet should also be fitted into all Battery Boxes which are using the Motor Cable entry holes as passing the cables through the 'OPEN' Grommet seals the hole best as possible & protects from the ingress of moisture & dust. 

To open the grommet to pass a cable through simply use a sharp Knife to press against the pre pressed slicing line & slice open the Rubber Membrane to allow you to push your cables through. Easy!

Mk II MASSIVE Monster Box BASE for 2WD

The Massive Monsterbox Base connects to all vertical panels in a Massive Monster Box or Double Stack Massive Monster Box. They are used with grommets to allow entry into the box by the phase and sensor cables, and the edges of the box are where the hex spacers mount. Additionally, the base is where any Monsterbox is mounted to the board. In this case that can be done via the standard bushing system or Dogbone mounting system. This panel is only designed to operate with 2 motors. 

Mk II MASSIVE Monster Box LID

The Massive Monsterbox MkV Lid rests on top of the side and end panels of the Massive Monsterbox MkV and centers the screws into the hex spacers to hold the box together.

Mk II MASSIVE Monster Box SIDE PANEL - BLANK LI-PO

The side panel is a structural component of the Massive Monster Box that connects the lids and base of the box together. 

Mk II MASSIVE Monster Box SIDE PANEL - CHARGER LI-PO

The Charging side panel is a structural component of the Massive Monster Box that connects the lids and base of the box together. It has cutouts for easy charging and an On/Off Switch.

Mk II MASSIVE Monster Box 2mm END PANEL - LI-PO

Structural component, like the side panels, to connect the lids and base of a Massive Monster Box together.

Mk II MASSIVE Monster Box 2mm CUSTOM VESC mounting PANEL - LI-PO

The custom VESC panel can fit a variety of VESCs to the Massive Monster Box. 

M4 x 16mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 80mm Aluminium Threaded Spacer Nut Used for assembling the BEAST Battery Boxes

Used for assembling the BEAST BATTERY BOX.

x7 Required per box

M4 COUNTERSUNK Washer Anodised

M4 Countersink Washer great way to pimp and customise your board in 10 differnt colours used in conjunction with all our M4 Countersunk bolts great way to finish off your board/project