Home»ELECTRIC COMPONENTS»Battery Boxes»BIGGEST MTB BEAST Box - 16Ah Li-Po»16A BIGGEST BEAST Box fits 1x VESC HD-60T

DESCRIPTION

Cable Harness for wiring Power Switches to VESCs

Harness allows connection between VESC 6 MkIII or newer and on/off switch.

TRAMPA Switch with 5V LED QUALA-T logo & 16mm Stainless Steel Fixing Nut

The TRAMPA 'QUALA-T" stamped Power Switch is a sexy little switch & to co-ordinate with the huge array of anodised & painted colours that TRAMPA offers to tie into all the other kit we offer is available in 6 different colours - RED, BLUE, YELLOW, GREEN, WHITE, PINKY/PURPLE

Which means no more loop keys!
All TRAMPA Mountainoboards Boards fitted with VESC 6 MKIII & any later models can now be fitted with power buttons for easy powering on/off and a much sleeker looking board!

You will need a Power Switch Cable harnesses to plug in

The QUALA-T Switch is Non-latching & limited to a Max voltage of 5v 

5mm ROUND BLIND Rubber Grommet for 5mm TRAMPA Silicone Cable

This 5mm Round Blind Grommet is used to seal off un used Motor Cable Entry Holes in the MONSTER Box, BEAST Box & Underboard BATTERY Box.

The 5mm Round Blind Grommet should also be fitted into all Battery Boxes which are using the Motor Cable entry holes as passing the cables through the 'OPEN' Grommet seals the hole best as possible & protects from the ingress of moisture & dust. 

To open the grommet to pass a cable through simply use a sharp Knife to press against the pre pressed slicing line & slice open the Rubber Membrane to allow you to push your cables through. Easy!

5mm Cable Entry OPEN Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes

5mm Cable Entry Open Rubber Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes in Monster Box side panels for water proof assistance & Neat Cabling

OVAL Rubber BLIND Grommet Cable Entry Hole - Fits in Monster Box side panels for water proof assistance & Neat Cabeling

This OVAL Rubber BLIND Grommet Cable Entry Blank is used to seal of Entry Holes in MONSTER Box, BEAST Box & Underboard Battery Tray which fits on the ORRSOM longboard. Simply push the Oval Grommet into position & your entery holes is sealed from moisture & dust.

If you need to push a cable through, use a sharp knife and carefully slice through the rubber membrane.

16A BIGGEST BEAST Box kit inc Mounting Panel to fit 2x VESC 6 with LED Screen & NRF Housing 16000 mAh cell packs!!

TRAMPA’s Beast Boxes come in three different sizes;

STANDARD - fitting up to 6200mAH Batteries

BIGGER - fitting up to 12,000mAH Batteries

BIGGEST - fitting up to 16,000mAH Batteries.

Boards with single motors could go for any of the Beast Boxes - dependant on the desired range / weight of the finished board.

Boards with TWIN Motors will need to go for the BIGGEST BOX, in order to accommodate room for the extra VESC that needs to sit inside.

Able to fit onto any TRAMPA board with Spring Trucks, BEAST BOXES made from 2mm thick 3k Twill Carbon Fiber & are precision CNC machined & internally grooved to give perfectly fitted joins, making the Beast Box pretty much water proof. Heat shrinking your joins & adding a touch of silicon at the end of the assembly will for sure seal the box to be tight from water!

The beast box comes with a top mounted LCD Battery Indicator, so guessing range is no longer an issue!

Assembling the box has been described as “fiddly but fun”. It’s a tight fit when using the biggest batteries for each box, so keep that in mind while assembling. The less room the batteries have to bounce around inside the box the better - especially over rougher terrain!

Stainless steel Countersunk bolts harmoniously connect into both the base & the lid of the box, screwing neatly & tightly into HEX spacers... as the lid is tightened down, you'll get a satisfying click of confidence that everything has dropped into place perfectly, as the panels slips into the groove and the gaps are no longer visible!

Battery Box Width - 110m
Battery Box Length - 200mm
Everything fits Internally!

M4 x 10mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 35mm TORX Countersunk Bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 25mmTORX Countersunk Bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M6 x 30mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

- 6-8s Battery Box

- 8-10s Battery Box

-Beast Boxes

M4 x 80mm Aluminium Threaded Spacer Nut Used for assembling the BEAST Battery Boxes

Used for assembling the BEAST BATTERY BOX.

x7 Required per box