URBAN BELT DRIVE
Urban Belt Drivetrains are CRAZY customisable – able to work with a range of slave pulleys & almost everywheel TRAMPA has to offer, the possible applications for these drivetrains are endless!
Using premium Carbon mounting panels & T6 aluminium Truck connectors, the finished motor mounts have an amazing strength-to-weight ratio.
Fit to ATB SPRING TRUCKS.
TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.
TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.
TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.
As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.
& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.
TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA SUPERSTAR HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim of the SUPERSTAR HUB eventually screwing into the M4 nut on the other side easly.
Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.
USED FOR CONNECTING:
This ia 460mm long x 15mm wide High Torque Drive (HTD) Re-enforced Rubber Belt, which has 5mm Tooth Spacing (5M). This Belt is High Power rated (HP) & arguably over engineered for our application as the belt is made in Germany by the world famous company called STRONGBELT, who usually supply into heavy industry public sector applications which demand much more stringent requirements of any electric skateboard! This belt is used to transfer the power from the Motor & Motor Pulley into power at the rear wheels of a TRAMPA Electric Mountainboard.
TRAMPA opted to set a new standard in E-Skating, becoming the first in the world to fit to all of its E-Boards, a 15mm wide TRANSMISSON BELT. Our standard 15mm belt is almost double the width of nearly all other E-Sk8's out there, they tend to use a flimsy off the shelf 9mm transmission belt which are prone to stretch, slip & ultimately snap. Using a re-enforced 15mm wide High Power Belt reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. When accelerating or engine breaking (KERS), even from a standing start the STRONGBELT power is smooth & does not slip, or strain the motor, it does a damn gooood job!.....
STRONGBELT, as their name suggests, is a Heavy Industry German Brand that usually supplies the likes of Train manufacturers where serious levels of quality with no excuses on failure are expected from the product, as failure for such an item is serious & may result in death! STRONGBELT weave KEVLAR into their Pulley Belts, Kevlar is one of the strongest fibers known to man, its often added into materials to gain extra strength.... STRONGBELT have the best reputation in the Power Transmission Industry for NO stretching or snapping & we have high expectations from this quality item.
These extra quality details in the production of our electronic motor drives, provides the maximum responsiveness achievable whilst maintaining a super smooth power delivery to the rider at all times.
This part ensures your motor is supported and the belt is running straight - two very important jobs for a smooth, fast and reliable board.
Motors with longer axles, like TRAMPA’s own, will fit perfectly into the housed bearing within, supporting the axle rotation, ensuring there is no ‘give’ in the axle, where the belt could potentially slip off at high speeds.
Fitting onto Channel Truck Motor Mounts this Motor Axle Support will work with any of the 6-9inch tyres in the TRAMPA range.
TRAMPA's 15mm wide 13-15 Tooth Motor Pulleys connect directly to the Motor Axle & are secured into position using a Magnetic Fixing Key & 4mm Locking Grub Screw.
These custom made Motor Pulley Wheels fit 15mm wide STRONGBELTS, which should never stretch or break whilst at the same time providing a very smooth power delivery to the user - even from a standing start.
Choice of Aluminium or Black Steel. Aluminium Pulleys are perfect for those looking to save every gram possible on their board - Black Steel Pullys are heavier, but much harder wearing.
Changing your Motor Pulley &/or Drive pulley wheels will drastically change the performance of your ride... :-)
Best performance for climbing steep inclines.
Best all-round performance
Best performance forreaching top speeds.
TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.
TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....
TRAMPA's 66 Tooth URBAN mount Slave Pulley fits to any of the HYPA, SUPERSTAR or PRIMO wheels in the TRAMPA product Range & are used when connecting electric motors to the URBAN Motor Mounts.
The 66 Tooth URBAN Slave Pulley has been precision milled from super-light-weight & mega strong Heat Treated T6 Aluminum. The pulleys teeth stand 5mm tall, this is the same size teeth as that found on TRAMPA's 15mm wide 'Strongbelt' & when TRAMPA's Premium Strongbelts are wrapped around the pulleys, using the belt tension facility to screw down & increase the tension on the belt the connection between the teeth & the belt becomes so efficient it has what we call HIGH TORQUE DRIVE (HTD). HTD ensures all of the motors Torque is forced through the pulleys to the wheels & when coupled with the amazing VESC 6 & 12s Battery power provides instant smooth unreal Power on tap to the rider!
With the use of some very special Threaded Hex Spacers & Socket capped Bolts the 66 Tooth URBAN Mount Slave Wheel connects directly into any of the GUMMIES, 6.5, 7 or 8 Inch SUPERSTAR or HYPA Wheels as well as into the PRIMO 3 spoke 9 Inch wheels to give a massive final drive... - 1 pulley, 3 uses, Amazing! :-)
TRAMPA's 66 tooth URBAN Mount Slave Wheel works in conjunction with all & any of the 13, 14 or 15 tooth Motor Pulley in the range. Changing your Motor Pulley will drastically alter the performance & characteristics of your ride... 13 Tooth is best for Hill Climbing whilst 15 Tooth is best for high speed, 14 tooth will give you all round performance...
To connect to HYPA hubs you'll need 6x 17x4mm Threaded Hex spacers
To connect to SUPERSTAR hubs you'll need 5x 15x4mm Threaded Hex spacers
To connect 6.5 & 7 Inch Wheels use 460x15mm Belt
To connect to 8 & 9 Inch Wheels use 475x15mm Belt.
TRAMPA’s amazing Carve Board drivetrains have been described as providing “A Whole New Riding Experience” – & that’s not wrong.
Suitable for STICKIES, GUMMIES & URBAN TREAD wheels, TRAMPA’s completed Carve Boards feel & perform unlike anything else on the market.
The beauty of a Carve board is in the set up – or rather – how you set it up… One choice of parts creates a board capable of straight-line bombing at insane speeds. Another choice & it’s a board so buttery it can turn any corner on a dime.
CARVE DRIVETRAINS ARE AVAILABLE IN TWO MODELS:
ORIGINAL carve motor mounts use super strong 3k Twill Carbon Mounting panels & T6 Aluminium Truck Connectors to create a drive train with an amazing strength : weight ratio.
Different Carbon Mounting Panels are needed for mounting different wheels.
MKII carve motor mounts use an all-in-one TRUCK CONNECTOR & MOUNTING PANEL. CNC’d from a solid block of T6 Heat-treated Aluminium, the MkII Carver Motor Mount Connector Panel can withstand the knocks & pumps that come along when riding, while staying secure and aligned on the truck.
Carve board drivetrains are all available as Single or Twin Motor setups. Single motor boards are easier on the wallet, & will still hit the same eye-watering speeds as twin motors. Twin motors split the brunt of the work, so less chance of motors over-heating, & twice the grip - so if you’re looking for a board that’ll fly off the line, you’ve got to go twin!
Carve boards can fit any of the 118-160Kv 6364 DC Motors we offer. 118Kv Motors are the choice for particularly hilly areas, whereas 160Kv Motors will carry you to some insane speeds!
Being belt driven, the gear ratios can be fine tuned with a range of Motor & Slave pulleys.
Carve board drivetrains attach to MINI SPRING TRUCKS - TRAMPA’s most multifunctional steering system yet! Using offset axles, its possible to reverse the hangers - changing the wheelbase, ride-height and performance of the finished board – allowing different sized pulleys & wheels to be fitted.
12.5” wide with 9.525mm axles, available in;
This simple motor mounting kit is as versatile as they come - able to work with most Longboard Trucks and wheels - as well as a variety of motor & pulley sizes.
The Motor Mount Connectors snuggly slide over the truck hanger and are secured tightly with MARINE GRADE M6x10 grub screws. The Premium Quality Carbon Mounting Panel is secured to the Motor Mount Connectors - & is fitted with a support for long motor axles. The Motor Axle Support houses a precision 608 bearing, supporting axle rotation & ensuring the motor is as secure & efficient as possible. TRAMPA’s motors have a longer axle, that fit perfectly into this support.
The Pulley Kit includes a 15mm STRONGBELT and a choice of Slave Wheels, that can drastically change the performance of your finished board. We use a 15mm wide reinforced drive belt that reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. This kit comes with a 66 tooth slave wheel, which fits to any of our 7-9 inch wheels!