This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

TRAMPA's MkII Electric GUMMIES Carveboard - uses Mini Spring Trucks with MkII Carve board Motor Mount,s Custom TRAMPA hubs & 125mm GUMMIES longboard Tyres - SINGLE Motor FULLY LOADED

TRAMPA's MkII Electric GUMMIES Carveboard - uses Mini Spring Trucks with MkII Carve board Motor Mount,s Custom TRAMPA hubs & 125mm GUMMIES longboard Tyres - SINGLE Motor FULLY LOADED  35° Original 9-69 Carve Deck Drillage for Trucks - Accurate and neat 35° TRAMPA Carve Deck - Drilled, Edged, Fitted with JESSOP Grip tape & a Marine Grade Stainless Steel Countersunk Bolt kit 35° TRAMPA Carve Deck - Drilled, Edged, Fitted with JESSOP Grip tape & a Marine Grade Stainless Steel Countersunk Bolt kit 35° TRAMPA Carve Deck - Drilled, Edged, Fitted with JESSOP Grip tape & a Marine Grade Stainless Steel Countersunk Bolt kit Mini SPRING TRAMPA TRUCKS - CNC FORGED Channel Hanger with 9.525mm Axle with precision CNC Baseplate Mini SPRING TRAMPA TRUCKS - CNC FORGED Channel Hanger with 9.525mm Axle with precision CNC Baseplate Mini SPRING TRAMPA TRUCKS - CNC FORGED Channel Hanger with 9.525mm Axle with precision CNC Baseplate Mini SPRING TRAMPA TRUCKS - CNC FORGED Channel Hanger with 9.525mm Axle with precision CNC Baseplate TRAMPA's MkII Electric GUMMIES Carveboard - uses Mini Spring Trucks with MkII Carve board Motor Mount,s Custom TRAMPA hubs & 125mm GUMMIES longboard Tyres - SINGLE Motor FULLY LOADED  Custom TRAMPA hub with Gummies 125mm Longboard Wheel Tyre Custom TRAMPA hub with Gummies 125mm Longboard Wheel Tyre 12mm ATB Bearings with 9.525mm Bearing Reducer Sleeves for complete board MkII GUMMIES CARVEBOARD Motormount Connector Panel & 44 Tooth Pulley Kit & Motor - SINGLE VESC 6 MkV In CNC T6 Silicone Sealed Aluminium Box with Genuine XT90 Connectors - Vedder Electronic Speed Controller TRAMPA Special VESC 6 MkV In CNC T6 Silicone Sealed Aluminium Box with Genuine XT90 Connectors - Vedder Electronic Speed Controller TRAMPA Special BEAST Box options for CARVEBOARDS 6 - 12Amp BULL BARS for CARVE BOARDS T6 Heat Treated CNC'd Aluminium Uprights, with Hollow Aluminium Stash Tubes with Rubber end bungs Complete 16A BIGGEST BEAST Box 12s1p Cable Kit with 50 Amp Fuse all soldered & heat sealed ready for plug & play use TRAMPA Stamped 1036 strand Silicon coated Cables! WAND WAND WAND WAND Graupner Ultramat 18 charger - capable of charging 2x 6s Batteries at once with balancing cables Luxury Travel Bag - Fits 15º short decks with 8 Inch wheels perfectly Luxury Travel Bag - Fits 15º short decks with 8 Inch wheels perfectly
From
£1,300
exc tax
schematic

flexometer

By altering the number of layers of material that we add into the mould, we are are able to tune the final performance of the TRAMPA decks relevant to the riders weight height & ability. Please use the FLEXOMETER above as a guide to help you choose the right ply board for you. TRAMPA's FLEXOMETER information is to be interpreted as a 'GUIDE ONLY' as there is no fixed rule as to which is the exact right deck for you. The weight, height & ability of the rider will all help determine which is the right sort of deck for you, but of course the most important factor is personal preference as to how the rider wants their deck to feel.... Some riders like it flexi, some like it firm, some like it very very stiff.... It depends on what you are doing on your board, i.e. freestyle, freeride, boarder-cross, altho there is guidance there is no right & no wrong just personal preference but when purchasing a deck from TRAMPA we want to make sure you get it exactly the way you want it! so if your stuck as to which one is the best for you them please drop as a line...

GUMMIES Carve Board can cruise over cracks & bumps that might stop the STICKIES, and with none of the roll resistance found with pneumatic tyres, this board is a beast on smooth surfaces! Compatible with 44 tooth Slave Wheels, when paired with the right Motor Pulley this board will be cruising at 35mph no problem!

Check out the Gearing Chart for more information.

GUMMIES Tyres work with HYPA (125g), SUPERSTAR (179g) & MEGASTAR (292g) Hubs.

GUMMIES & URBAN Carve Boards use the MK2 Motor Mount Connection Panel. Stepping away from the Carbon Panels & Truck Adaptors, the Mk2 Motor Mount Connection Panel is an all-in-1, CNC’d T6 Aluminium panel that guarantees secure & accurate Drive Train attachment. 
Because both boards use the same Motor Mount Connection Panel, a quick & simple swap of Pulleys, Belts & Wheels gives a whole new board, with new terrains to shred. We’re offering PRO Carve Boards with these parts as a kit - for those keen to experience 2 boards in 1!

TRAMPA’s amazing range of Electric Carve Boards have been described as “A Whole New Riding Experience” – & that’s not wrong.
Available with STICKIESGUMMIES & URBAN TREADS wheels, TRAMPA’s Carve Boards look, feel & perform unlike anything else on the market.

The beauty of the Carve board is in the set up – or rather – how you set it up… One choice of parts creates a board capable of straight-line bombing at insane speeds. Another choice & it’s a board so buttery it can turn any corner on a dime.

Carve boards are all available with Single or Twin Motors. Single motor boards are easier on the wallet, & will still hit the same eye-watering speeds as twin motors.
Twin motors split the brunt of the work, so less chance of motors over-heating, & twice the grip - so if you’re looking for a board that’ll fly off the line, you’ve got to go twin!
Carve boards can fit any of the 118-160Kv 6364 DC Motors we offer. 118Kv Motors are the choice for particularly hilly areas, whereas 160Kv Motors will carry you to some insane speeds!
Due to the extra space needed for two VESCs, we can currently only offer Twin Setups using the BIGGEST BEAST BOX.

Measuring just 850mm tip-to-tipTRAMPA’s CARVER DECKS are balanced between being small enough to carry on a bus - & long enough to still feel substantial & stable beneath your feet at speed.
Using 35° angled tips, Carver Decks have the same flex & ‘pop’ as TRAMPA’s MTB decks, & work in conjunction with MINI SPRING TRUCK steering systems.
Choice of 14-16ply, available as;
STANDARD (2350g)
HOLY PRO (2200g)

Carve boards come fitted with a rear-mounted BEAST BATTERY BOX. Rear-mounting the batteries ensures the deck doesn’t loose any flex or ‘pop’, while leaving all the space for freedom of foot-placement.
Carve Boards are compatible with Under-Board Battery Trays. Under-Board Battery Trays may look sleeker, but they sacrifice clearance on the bottom of the board, as well as the flex of the deck itself – BEAST BOXES solve both these issues.
Having the weight of the batteries over the rear helps to give the back wheels extra grip – perfect when carving-tightly.
Available in;
STANDARD (Space for 2x 6200mAh Zippy Compacts & 1x VESC)
BIGGER (Space for 2x 12000mAh Batteries & 1x VESC)
BIGGEST (Space for 2x 16000mAh Batteries & 2x VESC)

Carve boards use MINI SPRING TRUCKS - TRAMPA’s most multifunctional steering system yet! A scaled down & improved version of TRAMPA’s already-amazing Spring Trucks, MINI SPRING TRUCKS give three points of adjustment to fine-tune the steering resistance - through Spring Adjustors, various colours of DAMPA, & finally by installing the springs closer or further away from the Kingpin.
MINI SPRING TRUCKS use reversible hangers – giving two sets of trucks in one! The axles have been mounted in an offset position, so when the hanger is reversed, the wheelbase length, ride-height and performance of the finished board is changed.
12.5” wide with 9.525mm axles, available in;
INFINITY (817g).
VERTIGO (737g).
ULTIMATE (703g).

It’s possible to attach T6 Aluminum BULL BARS to your front truck, which not only knocks the road-kill out of the way & potentially mows the lawn as you go, but also allows you to connect all kinds of things from lights, cameras, Sat-Navs, or anything else you may need on the front end of your board.

Carve boards are able to fit any style of Bindings & Heel Straps we offer. Using bindings gives a whole new level of confidence & control over the board. Allowing you to really lean into turns, hop up curbs & tick tack - bindings are a true game changer on Carve Boards.

You will need to supply your own Batteries to make the boards move. There are many options when it comes to cells; desired range & budget usually determine the sort of cells you should purchase. People often ask us what cells to use - & there are hidden issues with some cells, such as availability, price, shipping restrictions, wrong connectors, or complexity of build (especially when it comes to making custom build batteries). Taking all these factors into consideration, we found a regular supply of good performance cells from a variety of suppliers & consequently built our Battery Boxes around them. Check out our RECOMMENDED BATTERIES page for help. Easy :-)


 

35° Original 9-69 Carve Deck

Measuring just 850mm in length, TRAMPA’s CARVER DECK is the perfect balance between being small enough to take on a bus, while still feeling substantial & stable under your feet at speed.

With 35° tips, Carve Decks have the same flex & ‘pop’ as TRAMPA’s MTB decks, making them the perfect ‘urban-board’ choice for Mountainboarders. Working in conjunction with Mini Spring Trucks, the resulting Carveboards have been described as “a whole new riding experience”.


TRAMPA’s famous range of indestructible Decks are unlike anything else on the market. Tailored to a riders' weight, height & ability – TRAMPA DECKS give unrivaled responsiveness & confidence in the board when riding.

Created to replace dull unresponsive wooden decks & reinvent the off-road riding experience, TRAMPA decks bring a whole new riding-experience. With insane ‘pop’ & shock-absorbing flex, TRAMPA decks are the #1 choice for freestyle riding & comfortable cruising.  

Made using a secret re-enforced glass and plastic composite (originally developed for light-weight military applications), TRAMPA decks are indestructible. In 17 years of excessive & harsh testing - pushing the decks to their limits (inside & out of intended applications) - there has never been a single break!

TRAMPA decks are measured in “Ply”, referring to how many layers of ‘secret-composite’ are used when making the deck. A lower ply deck will be flexi-er & lighter than a higher-ply one. Generally we recommend higher ply decks for heavier riders, and lower for lighter riders – but flex, pop, and stiffness are all a matter of taste. Our Ply-ratings range from 11 - 18 in various lengths & shapes – meaning there’s a perfect TRAMPA deck for everyone!

TRAMPA decks have 35°, 15° or 0° Truck Mounting Angles, in order to work with the various steering systems used across different applications.
35° Decks – Work in perfect harmony with TRAMPA’s amazing Spring Trucks – a highly tuneable steering system designed give optimal responsiveness at 35°.
15° Decks – Fit to ATB Skate Trucks – a lightweight & cheaper steering system, perfect for lighter riders & kiteboarders.
0° Deck – Our ORRSOM Longboard Deck uses a special split-tip that allows 12FIFTIES Longboard trucks to be mounted at 3 different heights. 


How are they made?

The TRAMPA™ deck is made from a re-enforced glass and plastic thermo composite. Chosen because it gives a superior strength-to-weight ratio, whilst (unlike carbon fibre) remaining flexible. It is able to withstand huge impacts, forces and flex's that would shatter other materials.

Specially formulated, and presented in a thread like format, just like cotton. From there, it’s woven to our desired width, and placed it onto a roll. Pre-shaped, polished-aluminium moulds are used to give the material the dimensions and surface quality we require – this is where we vary the layer quantity of the composite in the mould, & control the amount of flex and pop in the resulting deck, giving us our Ply Ratings.

A special seal is used to create a high-pressured vacuum, then mould is then placed in a special oven to cook for about 2 hours. As the air is sucked out, the heated material becomes fluid – then at the crucial moment heating is turned off and the moulds are cooled, resulting in one solid piece! The decks are then cut out using a high-pressure water-cutter, resulting in a razor sharp finish to the edge of the deck.

The decks are then finished by hand. The binding and grab handle fixing holes are measured and drilled by hand, Metal files are used to take away the sharp edge of the deck and they are then rubbed smooth with a block and various grades of sandpaper.


TRAMPA are happy to announce that we can now offer CUSTOM PAINT JOBS on our decks. We’ve been releasing our parts in an amazing selection of colours - and now it’s time we offer the deck to match!

We’re luckily sited next to an awesome car spray shop, which are happy to take on some of our decks and make them shine! They know their paint, and know techniques for making any colour pop, without adding too much weight to the finished deck - guaranteeing a perfect & even finish that’ll last for years.

We’ve got a wide range of colours for you to pick and choose from, or you can send over a pantone of your own and we’ll match it the best we can!

Custom Sprayed Decks costs £100 extra, and should be ready to ship two weeks from your order.

The 35° TRAMPA Street Carver deck is the latest deck in the TRAMPA range. It has been specifically shaped to work with the new Street Carver range of Truck steering systems. Choosing a low ply flexier deck makes carving on the street a fantastic sensation, whilst choosing a stiffer deck & adding DAMPA's into the Trucks tightens the steering turning the deck one of the fastest & most stable decks on the market!

The 35° TRAMPA Street Carver deck is available in 3 different flex rates, 14ply is the most flexible, 16ply is the stiffest. Please use the FLEXOMETER in the TAB ABOVE for guidance as to which is the most suitable ply deck for you or mail this link if you need some extra guidance. The 35° TRAMPA Street Carver deck is only supplied as Drilled, Edged & Sanded, Fully Gripped & with Marine Grade Stainless Steel Bolt Kit!

Regardless of which deck you choose, all TRAMPA Decks are totally Un-Breakable! We offer you a lifetime gaurantee! Our incredible composite material is so strong whilst still flexible, the material will not split, delaminate or break in any way regardless of the environment you use it in. TRAMPA decks are considered the "Poppiest" decks on the market, the performance is un-matched, you will fly higher & have more cushioned landings thanks to the performance of the deck! All TRAMPA deck's are customised to suit the riders weight, ability & personal preference.

Mini SPRING TRAMPA TRUCKS - CNC FORGED Channel Hanger with 9.525mm Axle with precision CNC Baseplate

The ULTIMATE CARVE TRUCK is a MEGA light weight version of the Infinity Carve Truck! Made in exactly the same way as all of TRAMPA's Spring trucks, using FORGED Alloy for the HANGER, the Ultimate Hanger has been CNC precision machined cutting out the bulk of the hanger bodies material, but without removing any of its critical strength! The Ultimate Carve Hanger is as its name suggests, the ULTIMATE & it has been fitted with weight saving 9.525mm (3/8ths of an Inch) TITANIUM AXLES instead of the standard 9.525mm Solid Steel Axles found on the Infinity Truck.

The Ultimate Hanger is connected via a TITANIUM Kingpin to an incredibly strong EXTRUDED & T6 HEAT TREATED Aluminum BASEPLATE which has also been CNC lightened. Comparing to the assembled Infinity Truck, the Ultimate Truck is over 25% lighter!!

The Hanger & Baseplate "Kingpin Holes" are also CNC precision milled. NYLON BUSHINGS are inserted into the Kingpin holes of the Hanger & Baseplate, allowing the Baseplate to slip over the Hanger allowing the Truck to assemble like a dream & to eliminate wear between the moving metal parts. An 8mm KINGPIN is used to connect the 2 integral Truck parts together & allow the steering to happen... 

SPRINGS (which could be loaded with DAMPA's) are squeezed by hand, into the mounting positions between the Hanger & Baseplate. When anchored in position using the countersunk bolt and Spring Adjuster to hold them tight, the springs give immediate firmness to the steering. The steering resistance can be pre-set to your weight, riding ability & personal preference. The Steering resistance can be easily adjusted by using a 4mm Allen Key & turning the SPRING ADJUSTER clockwise for more resistance or Anti Clockwise for less resistance. pre-loading the resistance in the spring suitable to the road ahead.

Additionally a TRAMPA DAMPA's can be fitted into the springs to add extra steering resistance to the spring..... TRAMPA DAMPA's come in 5 different hardness & there is a DAMPA for every type of rider! You can quickly adjust your board relevant to the conditions or terrain ahead...

Over time your riding will improve & you will demand more pre-tension (performance) from your steering. So remember the DAMPA's need some room to work & therefore don't over tighten your springs squashing the DAMPA's too much because ultimately they will split, instead change your DAMPA's to a slightly Harder Shore Resistance & back off the spring adjuster.

TRAMPA's Urban Carve Board is the perfect all round deck aimed at Snowboarders, Surfers, Skaters, Longboarders & of course Mountainboarders wanting to cross over to ride the Tarmac....

Custom TRAMPA hub with Gummies 125mm Longboard Wheel Tyre

TRAMPA's new & AMAZING 125mm GUMMIES Tyres are a 'Revolution' in the boarding world ;-) The GUMMIES Wheels are so good its as if the Longboard wheel has just been re-invented! The Gummies Tyres fit too & transform the performance of both of TRAMPA's HYPA & SUPERSTAR off road wheels, converting them into Supersized Longboard style wheels & are a completely new sensation & divine dream to ride!

Being 125mm in Diameter the GUMMIES Tyres are much larger than any other Longboard wheel on the market, whilst using High Quality SUPERSOFT Urethane (75a) & the same 50mm wide surface contact as the TRAMPA Stickies Longboard wheels not only do the GUMMIES Tyres perform like their name suggest (When riding on fresh tarmac / asphalt - Hard Packed surfaces, the GUMMIES Tyres stick like 'XXXX to a blanket' allowing the most insane turns & carves that you would not believe were possible) BUT the Super Soft Ultra Premium Urethane we have used also allows the GUMMIES Wheels to glide over cracks in the pavement & smash through the small obstacles that often get in the way when cruising around town, potentially jamming up smaller sized longboard wheels which can be well scary when it happens!!

Boarding of all kinds has recently seen a massive revolution with many new riders coming on the scene adding electric motors & powerful batteries to their boards, you could say much of the equipment being used by other brands is just not up to the job,  riding small wheels on high speed electric boards can be frightening and well when you hook up the TRAMPA GUMMIES wheels onto one of the new TRAMPA Electric Boards, the GUMMIES tyre performace comes into a whole new universe of riding experience that nobody ever knew existed before...!! All of TRAMPA's electric boards are all incredibly powerful, just the most un-real performance is experienced like nothing else ever.... Honest! Fitting a set of GUMMIES to 16 Inch wide ATB Spring Trucks in place of off road tyres converts your Mountainboard into a Street Monster, Racing around places like go-kart tracks will soon become the latest thing too do & we know the mega grippy GUMMIES tyres will become the #1 choice of all serious high speed riders.....

GUMMIES are currently available in BLACK BLUE or RED but all in the same super gummy 75a Soft Premium Urethane. The GUMMIES Tyres will only fit to TRAMPA Hubs HYPASUPERSTAR or AMAZING 8 inch MEGASTAR hubs, which in turn fit to any of the TRAMPA Truck Steering Systems and now using the new SPOKE SUPPORT CONVERSION SPACERS that fit to both the SUPERSTAR Hubs & the MEGASTAR hubs

Diameter - 125mm
Width - 52mm
Surface contact - 50mm
Fits to - HYPA & SUPERSTAR Hubs (9.525mm or 12mm Bearings)
Fits to - All 9.525 or 12mm TRAMPA Axles with 34.2mm of clearance.

BEAST Box options for CARVEBOARDS 6 - 12Amp

TECHNICAL

VESC 6 MkV In CNC T6 Silicone Sealed Aluminium Box with Genuine XT90 Connectors - Vedder Electronic Speed Controller TRAMPA Special

Introducing the amazing VESC® 6 MKV Speed Controller, the fourth major product update of the world famous VESC 6 motor controller product line. Packed with a variety of amazing new features, this VESC motor controller is certainly worth of it’s pimpin’ gold logo.

The first VESC controller capable of hibernating, your board can conserve power while not in use - reducing power consumption to just 20μA – less than the self-discharge rate of the batteries. Or with automatic power off, your VESC controller can switch itself off after a set amount of time.

No more loop keys! Compatible with power buttons / switches, the VESC 6 MKV controller can be ready to go with a single press / flick. If desired, multiple devices can share a single button.

Roll-to-start – it’s possible to set your board to power up with a small kick/nudge!

In its development, no Mosfet switches were used - due to their tendency to eventually blow up. This saves on the additional costs of replacing them, & also adds to the longevity of the VESC 6 MKV.

When we developed the VESC 75/300 controller, it was obvious that most of its features would be handy to have in the VESC 6 controller format.  As a result, Benjamin Vedder took on the challenge and re-designed the entire PCB of the VESC 6 controller, to make new, powerful features available in a smaller & cheaper 60V rated package.

The VESC 6 MKV controller features THREE PHASE SHUNTS & adjustable CURRENT / VOLTAGE FILTERS - detecting any motor attached more precisely and reliably than ever before. Consequently all kinds of motors now run as smooth as butter & react PERFECTLY LINEAR to throttle input commands.

You’ll also find a new IMU chip fitted - featuring a gyroscope, accelerometers and a compass, the VESC 6 MKV knows its 3D orientation in space, 3 axis acceleration values and directions. 

UAVCAN has been added to the firmware allowing to interact with commonly used flight controllers like the PIXHAWK ®* devices. An incredible 12,000 lines of code have been added for the new hardware releases. To make the VESC controller nearly indestructible, the low voltage rails were redesigned A-Z.

VESC-Tool software is now available as an Android™ compatible App, allowing you to configure your VESC or VESC controller array with only a few clicks. User specific PROFILES will let you change in between different setups with a single tap on the fly.

Using an original VESC 6 MKV controllermotor detection is now more precise than ever. Extreme low inductance (0.5 μHmotors are no issue! 

Parameters for gearing and wheel diameter have been added, allowing display of speed, Wh usage per distance travelled, precise battery indicator, current consumption, duty cycle and power. Beautiful self-adjusting analogue displays make the readings of all parameters very enjoyable.

What makes the original VESC hardware so special?

The original hardware is perfectly matched to work seamless withe VESC-Tool software code. Both, hardware and software, have been designed by the same engineer, knowing all critical detail.

TRAMPA BOARDS LTD has teamed up with the internationally renowned 'YODA of electronics' (Benjamin Vedder) to bring to the world the most advance electronic speed controllers ever to be produced! Benjamin's family name is Vedder & the V in the brand VESC represents this. VEDDERs Electronic Speed Controller! There have been many ESC's before, but now the VESC line of products officially exists, made to work seamless with the latest software developments. Benjamin is globally renowned for his incredible electronics and software skills. He has worked tirelessly for well over 7 years fine tuning preceding versions of the globally famous & Trade Marked VESC products & after teaming up with TRAMPA BOARDS Ltd the development of the VESC product line has taken him to his highest capability yet.

The TRAMPA VESC controllers  comes fitted as standard with TRAMPA's very own & very special Silicone Coated & TRAMPA logo'd cables which are made up of 1036 Strands of Highly Flexible Top quality German copper. These quality details ensure the maximum performance at all times. Attached To the premium copper cables are genuine Amass XT90s connectors one side & 4mm Gold Plated Bullet connectors the other. The VESC 6 MKIII is installed with a custom moulded Internal Silicone Seal & is neatly fitted into the Heat sink which is a Solid Block of CNC'd  6061T6  Aluminum, used for dispensing the heat and offering maximum protection, allowing easy fitting and maximum good looks!..

The VESC line of produces are the most powerful & impressive Electric Speed Controller Benjamin has ever envisioned! They are  arguably by far the best and most versatile Electronic Speed Controllers the world has ever seen!! E Boarding, E-Biking, Remote control of all kinds including Drones & Robotics and Camera equipment (as well as thousands of industrial & recreational applications) are all about to be revolutionized by using the VESC series of products that will all come to the market soon...

Using the a VESC controller in your TRAMPA BOARD setup (Regardless of which model) will allow you to add any battery up to 12s with 60V of peak voltage. This is the perfect limit to give you incredible performance from your electric TRAMPA motors or similar. Using the new VESC TOOL software, you will be able to fine tune your performances relevant to your application, where you will be able to calculate your top end speeds & approx distance to travel using different combinations of power & gearing settings. Beautiful!

VESC controllers comes to you ready to plug in & go! They are delivered to you in a very stylish precision cut 6061 T6 aluminum heat-sink housing which has the TRAMPA & VESC logo beautifully laser etched to its surface & for further splash proofing we have invested into another mould for additional exterior Silicone Sealing which is available as an accessory to purchase.

The performance of the TRAMPA VESC controllers, compared to preceding third party models, is light years ahead! This is demonstrated in the cost as cheap non effective clones are sold according to their price not their quality. If you want the best performance then stick to the original hardware source - it will save you a lot of money on the long run and is a guarantee for ultimate performance and max compatibility with future software releases.

Our VESC controllers are being configured with the brand new Open Source, GPL V3 licensed VESC®-Tool Software:  www.vesc-project.com and on the Google Play Store™*.
The Open source, GPL V3 licensed VESC Firmware will come pre-installed on the device, allowing us to do extra testing of the device, prior to shipping.
This is the GPL V3 license contract for your reference:  www.vesc-project.com/GPL V3

Features

- Current and voltage measurement on all phases (three phase shunts)
- Adjustable current and voltage filters
- built in IMU chip (accelerometer, gyro)
- Regenerative braking
- Traction control (single and twin setup)
- Sensored or sensor less operation + hybrid mode
- Configurable RPM-, current-, voltage- and power limits
- Input source: PPM, Analog, NRF Nyko Kama Nunchuck
- Communication ports: USB, CAN,UAVCAN, UART
- Throttle curve and ramping for all input sources
- Separate throttle curves for acceleration and brakes
- Seamless 4-quadrant operation
- Motor revolution, amp hour, watt hour counting
- Display of speed, power, duty cycle, amp flow, estimated range and battery status on App
- Accumulated data from arrays of VESCs
- Real time data analysis and read out via communication ports
- Real time data analysis and read out via VESC-Tool APP or VESC-Tool software
- Adjustable protection against:

          -    Low input voltage
          -    High input voltage
          -    High motor current
          -    High input current
          -    High regenerative braking current (separate limits for the motor and the input)
          -    High RPM (separate limits for each direction).
          -    Over temperature (MOSFET and motor)

Technical Data Sheet

- Voltage: 11.1V – 60V (Safe for 3S to 12S LiPo).
- Voltage spikes may not exceed 60V!
- Current: Continuous 80A, Burst 120A.  Values depend on the temperature and air circulation around the device!
- 5V 1A output for external electronics
- 3.3V 0,5A output for external electronics
- Modes: DC, BLDC, FOC (sinusoidal)
- Supported sensors: ABI, HALL, AS5047

* Android is a trademark of Google LLC.
Google and Play Store are trademarks of Google LLC.
PIXHAWK is a trademark of Lorenz Meier

Complete 16A BIGGEST BEAST Box 12s1p Cable Kit with 50 Amp Fuse all soldered & heat sealed ready for plug & play use TRAMPA Stamped 1036 strand Silicon coated Cables!

This complete Cable kit is used to link 2x 6s Batteries together. The batteries must be fitted with female XT90 connectors to connect to this cable kit. The cables pass trough a 50Amp safety fuse & connect into a single TRAMPA VESC to further power a single TRAMPA motor giving you the amazing 12s power that everybody is talking about! This cable kit shoul dbe used when using the rear mounted TRAMPA BEAST BOX... :-)

The finely stranded (1036 strands per 4mm core) & highest standard available copper cables (made in Germany) flex perfectly in their top quality & super flexible silicone coating to enable you to connect everything together neatly within the contents of the carbon fibre Beast Box, remember the VESC is mounted internally in the Beast Box and I can tell you it can be a bit of a squeeze fitting everything into the Beast, but having superflexible high quality cables to work with means everything can be easily moved around inside the box slipping them into the perfect position without the fear of damaging the cables or the hand soldered in the UK connections to the XT90 plugs... 

The XT90 plugs have a little ridge on their exterior whilst the material they are made from is very strong and very cleverly we have made the Beast box lid with 2 precision made holes perfect for accepting for the XT90's to push through the lid from the inside of the box & rest against the rim of the hole in the lid, allowing everything else in the box to seal away enabling you to be able to, with the use of some squeeze silicone in a tube to become pretty much weather proof... 

By the use of some suitably small 2mm holes next to the precision holes for the XT90 connectors it's possible in combination to neatly zip tie between the XT90's to lock them firmly in position  giving them a strong enough connection  so that so that you can easily push & pull the loopkey / cuicuit breaker at any time from the exterior with out the fear of damaging anything inside or out...!

The BEAST BOX is also fitted with more precision holes to allow tying the exterior VESC cables which come out of the rear of the Beast box to reach the motor whilst holding all the cables neatly in their best position.

Constructed using 4mm thick of the highest standard Copper available (that's lots of Super fine copper Strands - 1036 strands per 4mm core) and coated in Super Flexible Premium Silicone which has been TRAMPA Stamped to prove it's geniality & expected quality (Cus these top quality cables are not cheap) are used to maximise & maintain full performance in your Electric TRAMPA Board at all times! 

MkII GUMMIES CARVEBOARD Motormount Connector Panel & 44 Tooth Pulley Kit & Motor - SINGLE

TRAMPA’s amazing Carve Board drivetrains have been described as providing “A Whole New Riding Experience” – & that’s not wrong.
Suitable for STICKIESGUMMIES & URBAN TREAD wheels, TRAMPA’s completed Carve Boards feel & perform unlike anything else on the market.

The beauty of a Carve board is in the set up – or rather – how you set it up… One choice of parts creates a board capable of straight-line bombing at insane speeds. Another choice & it’s a board so buttery it can turn any corner on a dime.

CARVE DRIVETRAINS ARE AVAILABLE IN TWO MODELS:

ORIGINAL carve motor mounts use super strong 3k Twill Carbon Mounting panels & T6 Aluminium Truck Connectors to create a drive train with an amazing strength : weight ratio.
Different Carbon Mounting Panels are needed for mounting different wheels.

MKII carve motor mounts use an all-in-one TRUCK CONNECTOR & MOUNTING PANEL. CNC’d from a solid block of T6 Heat-treated Aluminium, the MkII Carver Motor Mount Connector Panel can withstand the knocks & pumps that come along when riding, while staying secure and aligned on the truck.

Carve board drivetrains are all available as Single or Twin Motor setups. Single motor boards are easier on the wallet, & will still hit the same eye-watering speeds as twin motors. Twin motors split the brunt of the work, so less chance of motors over-heating, & twice the grip - so if you’re looking for a board that’ll fly off the line, you’ve got to go twin!
Carve boards can fit any of the 118-160Kv 6364 DC Motors we offer. 118Kv Motors are the choice for particularly hilly areas, whereas 160Kv Motors will carry you to some insane speeds!

Being belt driven, the gear ratios can be fine tuned with a range of Motor & Slave pulleys.

Carve board drivetrains attach to MINI SPRING TRUCKS - TRAMPA’s most multifunctional steering system yet! Using offset axles, its possible to reverse the hangers - changing the wheelbase, ride-height and performance of the finished board – allowing different sized pulleys & wheels to be fitted.
12.5” wide with 9.525mm axles, available in;
INFINITY (817g).
VERTIGO (737g).
ULTIMATE (703g).

WAND

Introducing the Amazing WAND CONTROLLER

Frank Drenckhahn - King of design & production at TRAMPA & Benjamin Vedder - Creator of the VESC-Project  aka the 'Yoda of Electronics', spent the winter period of 2018/19 designing a revolutionary remote controller, with some new & very exciting 'E-Skate-specific-features' to work in direct relation with the VESC / TRAMPA series of products.

There are many basic remote control options already on the market, but none of them hit the high bar when it comes to features & reliability. Here at TRAMPA, we’ve experienced riding with in-sufficient, untrustworthy remotes. Consequently, we’ve always dreamed of holding a reliable, versatile, ever-lasting, informative & safe remote controller, that matches the outstanding performance of the VESC software & the TRAMPA equipment that they’d be so frequently paired up to. You should expect nothing less than magic whilst waving the WAND over TRAMPA assembled VESC Products!!

HARDWARE

High-end TRAMPA Electric boards deserve to be controlled with a high-end remote, you need to be 100% in control over the Monster under your feet! Personally, I always dreamed of something that feels nice in your hands, made of high grade material, with a little bit of weight to represent the same high quality level of our TRAMPA boards, and the cutting edge technology the VESC offers. This remote is made from 6061 T6 (Aero-grade) Aluminum with a sleek carbon fiber battery lid. You can see & feel the quality straight away.

REAL TIME DATA DISPLAY

The WAND remote is fitted with a circular high resolution OLED display that reveals all the crucial information you want to have at hand while riding your board. The screen might be small, but the list of data it shows is HUGE! You’ll be able to scroll through and see your current speed, average speed, amp draw, duty cycle, average watt hour draw, battery indicator (for both board & remote), recuperation and more to be added through firmware updates!

Whatever data the VESC controller captures can ultimately be displayed on the OLED screen. Benjamin even added in a few tools to display animated graphics, for ultimate pimpness!

SMART REVERSE

Ever over shot the junction & wished you could reverse a little to pull you back from the traffic? Well now with the WAND in your hand, pulling back on the Thumb Controller bringing you to a stop & keeping your thumb in the braking position will automatically instigate the Smart reverse feature which will ramp up enough Amps to switch the rotation direction of the motor but just at slow speed so that the board reverses you out of trouble..... A very very clever feature designed to keep our clients safe...

SAFETY & GESTURE Control: AN OUTLOOK TOWARDS FUTURE FW UPDATES

What is really exciting is the IMU (Inertial Measurement Unit) inside The WAND... The IMU knows the exact orientation of The WAND in space and gathers acceleration values of all the space axis at the same time, acceleration, speed & elevation. Using the IMU, Benjamin will in future be able to code some really useful safety features, as well as some playful things. For instance; one day the remote will be able to tell if you take a tumble & will be able to stop your board safely. It will know when it is resting upside down on a surface, and refuses to send accidental signals to the board. Powering up when you pick it up & going to sleep after 5 minutes of inactivity The WAND is smart enough to save its own battery! It can even be used as a water spirit level, helping you to align things perfectly! Expect some nice FW updates in the FUTURE. IMU features will become available over a period of time!

TRANSFORM YOUR REMOTE

On top of the features mentioned above, amazing piece of tech features the options to either be converted to a pistol grip style trigger remote, or to have an additional small trigger on the lower side to allow additional index finger control. I like to use my index finger to send acceleration commands, while using my thumb to send brake signal commands. Others want to use their thumb or index finger only. Much alike TRAMPA’s boards, these remotes are made to be customised around you!

SAFE KEEPING

We’ve all wasted too much time on the pre-riding ritual known as “Where the **** did I leave the remote?!” Well no more. We decided to equip The WAND with a Magnetic bottom panel. A small metal sheet or magnet attached to your board (stick a big washer to your Battery Box or similar), will keep your remote safe where it belongs all the time, or you simply keep your remote on the fridge, next to the car keys! 

BATTERY LIFE

Battery life has always been an issue in the past. Sometimes you want to go out for a ride, but you forgotton to charge up your remote. Then after a quick charge, you end up worried that it‘ll die before the end of your ride.

When Frank & Benjamin designed this remote, ultra low energy consumption was a prime goal to achieve.

We chose to use standard AAA batteries, so that you can easily carry spares & swap them out - like changing the batteries on your TV remote, giving you ultimate confidence that you will never ever run out of battery. Two tiny AAA cells are good for 30 hours of constant operation. AAA cells are available at gas stations, supermarkets, drug stores, or even in a remote house in the middle of nowhere in a kitchen draw, should you get real desperate while out on your endless trails!

SOFTWARE & SUPPORT

We don't want you to have to buy a new remote because the software becomes outdated, so we made sure this remote would have a USB & SWD port, allowing you to easily flash the latest firmware, and unlock the latest features when they get released. This remote is future proof & will surprise you many times over its life. The Wand Firmware will be Open Source. Please browse Benjamin Vedders Github for source files and copyright information : https://github.com/vedderb

OMPATIBILITY

This remote is fully compatible with the TRAMPA NRF Dongle. An NRF connection is required to pair the Controller to the VESC device. Depending on if or when you bought the dongle, you might need to update its firmware in order to make the connection to the controller though the VESC, which is a simple task. This remote is compatible with any ESC that is based on VESC technology, and running the VESC firmware. Simply plug the TRAMPA NRF Dongle into the UART port of your ESC.

CALIBRATION AND MULTIPLE BOARDS

This remote doesn't require calibration. A simple one click pairing procedure does the trick. This remote will become a solid partner to all your boards.  No more need for multiple remotes for lots of boards, unless you want to ride out with your friends. In which case you can leave your old PPM remote receiver plugged in & switch over to that using the VESC-Tool App.

In order to connect The WAND to your VESC or VESC software compatible ESC, you will need to do a firmware update on that ESC. Simply plug the TRAMPA NRF Dongle into your VESC controller & pairing is pretty much automatic, just follow the on-screen instructions. The TRAMPA NRF Dongle can be updated to the latest, compatible FW, using the latest desktop VESC-Tool.

Technical features for the WAND;

- Stable & safe with NRF wireless connection

- High resolution OLED display

- 2x AAA standard size battery which will give over 60 hours of battery life

- Exterior dimensions:144 x 31x 22mm

- Full Aluminum 6061 T6 SOLID CNC'd housing - Anodized Black with Laser Logo's

- Magnetic bottom panel. The remote sticks to metal surfaces for safe keeping.

- Easy connectable to thousands of devices

Modes that the WAND can control;

- Forwards

- Brake

- Reverse

- Cruise Control

- Pre-programmable to allow you to select between performance setups so you can switch between defined user profiles. Adjusts power levels, acceleration, top speed brakes performance. Define Profiles for Learner, Intermediate & Advance riders who will all prefer different setup's

OLED Display will show you;

- Current Speed

- Average Speed

- Amp Draw

- Battery status of Remote

- Battery status of Board its connected too

- Duty cycle

- Estimated range

- Watt Hour Consumption

- Many many more features yet to be written about :-)

Saftey;

- Shock sensor (will become available via future Firmware update)

- No signal when remote is turned head over (e.g. trigger resting on surface)

- Safe NRF based wireless communication

- Safe pairing to board

- No calibration needed

- No interference with other remotes (group rides)

- Auto power off, auto power on

- Regular firmware updates available

ADDITIONAL FEATURES

- Your Android Phone or Mobile device with the VESC App & the WAND remote will share the same connection to VESC giving seamless connectivity.

- Firmware can be updated via VESC-Tool

- Works with existing TRAMPA NRF Dongles (Dongle may require a Firmware update)

- Different size triggers to fit different sized fingers

- Can be transformed to be a 'Finger Trigger' style remote where an additional feature of adding a Handle for comfy holding

- Can be transformed to have 'Thumb Stick' & 'Small Trigger' on lower side (use index finger for acceleration and thumb for brakes)

- Built in IMU (gyro and accelerometer) Be surprised what magic this can do in the future.

Graupner Ultramat 18 charger - capable of charging 2x 6s Batteries at once with balancing cables

Link to battery indicator charger thingy

This GRAUPNER ULTRAMAT Charger is capable of Charging & Balancing all cells up to 12s in power. The Ultramat 18 charger is used by the TRAMPA team for charging all of our decks that use Zippy Cells for power. The charger comes with a UK or EURO Plug for wall plug in connection, XT90 Jack leads & 2x 7 pin adaptor plates which allow balancer cable connections from 2x batteries from 1s to 6s using JST Connectors.... As the Graupner is our suggested charger for the Zippy cells this charger is somehow incorporated into the design of our Battery Boxes so using this charger is nice easy to connect, it is reasonably fast to charge whilst it balances (looking after) your cells at the same time and you dont need to remove anything in order to charge as the cells are all snugly secured away in one of the amazing Carbon fiber boxes, which as it so happens have been designed special for this style of charger & easy charging... :-)

12s power is the perfect amount of power to be pushed through any of the TRAMPA Electronic products (12s should only be applied when using the very special TRAMPA VESC6 speed controller). When 12s power is pumped into the VESC6 you will be able to experience the kind of riding performance everybody is talking about. Do not push more power than 12s into the VESC6. Using a XT90 Battery harness cable kit to connect 2x 6s batteries together will double the battery power resulting with a 12s Battery WITHOUT Any soldering or Welding!! 

So as you now know, to achieve 12s power requires a minimum of 2x 6s Batteries (it could be more cells if you were custom making your battery or if you were achieving 12s from 6x 2s, 4x 3s or 3x 4s cells as they can all be harnessed together to make 12s power... but then you will most likely need an additional balancer cable harness or more chargers to charge/balance each cell individually if you want speedy charging), so for efficiency & simplicity we base our 12s power on the use of 2x 6s cells as generally speaking there are many good priced nice performing chargers put there which also have the ability to balance your cells to prevent failiure of the cell, already on the market are capable of charging up to 2x 6 cells at any 1 time,

which maximizes efficiency which in turn means less chargers & (of course if you are making a custom battery you will need a BMS complicated system & Soldering skills) so you either need  2x 6s Battery chargers or 1x charger that is powerful or large enough to charge 2x 6s batteries at the same time to reduce charging times & this GRAUPNER ULTRAMMAT 18 charger is the charger TRAMPA is currently recommending of using capable of charging 2x 6s cells at any 1 time, so if you are running 12s made up from 2x 6s batteries, using this graupner charger you can charge both 6s cells at the same time.... :-)

As well as suggesting our customers find the best performance through using custom cells to make custom battery packs & BMS (Battery management systems), this all gets a little complicated for the majority of our customers, so for ease of supply & speed of installation as plugging in the 6s Cells means no welding or anything messy like that, as well as achieving excellent performance & fabulous range, TRAMPA is strongly encouraging the use of the ZIPPY Compact 6200mAh 6s 40c Lipo Pack with XT90 connectors in on any of the Boards in TRAMPAs range that use either the 12s BEAST BOX or 12s2p MONSTER BOX, as these high power 6s Cells not ony fit perfectly into these custom made Carbon Fiber boxes, but the lids & sides of the Boxes have been CNC'd allowing the wiring loom to flow beautifully inside, further enabling the battery balancer cables to poke out of the rear or sides of the box, whislt most importantly allowing the Charging XT90 connectors to push tightly into & fit perfectly into the precision cut holes in the lid, which are secured int position by the use of s simple ZIPTIE, allowing for simple but very strong KEY connection for turning your board on or off & allowing a really easy plug n play to charge both 6s cells at 1 time when using this Grauper charger

You should set your charger to LiPo Manual, 6A and max possible mAh setting. Actually the limit of the charger is 20,000mAh I think. That only means the charger will stop charging when it pumped in 20,000 mAh. Worst case, you need to give the charger a second go to finish the job. It simply counts how many mAh it pumped in and stops at your pre-defined value.

When you press the two middle buttons simultaneously, while you charge, you can enter a mode that allows you to see each individual cell. +- buttons let's you flick through the cells. Each cell is fully charged when it's at 4.21V.

For an estimate of how long your batteries will take to charge use this Battery Charging Calulator

For example: Compact Zippy 6s 6200mah charged with a graupner (no booster - 2a charge rate) would be 3 hours 45 minutes

Luxury Travel Bag - Fits 15º short decks with 8 Inch wheels perfectly

Arrive like a Pro with a Tailor made LUXURY TRAVEL BAG. This quality bag is the perfectly sized to fit your 15° TRAMPA Skate Deck & your riding equipment into.

On the exterior, the Luxury bags Double Strength Chunky Zipper, un-zips all the way round to allow easy entry for the board. The LUXURY TRAVEL BAG is padded with 10mm EVA foam at the top, the bottom & at the sides to protect your board from impacts during transit. Top quality Stainless Steel Zippers, pimped out with custom made TRAMPA Zipper Pulls, makes zipping & un-zipping the bag a total pleasure. For your security whilst traveling your bag is supplied with a Padlock & key.

CHUNKY CARRY HANDLES join at the side of the bag & with the use of a velcro strap they connect comfortably together. Brushed Aluminum Quick Release Dog Clips attach or remove the Double Padded & Adjustable length Shoulder Strap, making carrying it down the beach or through the airport as comfy as possible. There is also a quick access Exterior Travel pocket for storing documents and the likes & Re-Enforced Grab Handle at the end of the bag to assist in lugging the bag around.

The interior of the bag is lined in strong Nylon making slipping your board into the bag very easy to do. It also has Super-long Velcro Pockets that run the entire length & depth of both sides of the bag, allowing you to be able to safely store your Bar & lines within. Steady straps wrap over the deck, anchoring it in place to avoid rolling around, making it more comfortable to carry.

The Luxury Travel Bag is best used in conjunction with the TRAMPA MUCK OFF BAG, as its name suggests, it keeps the muck off & keeps the Luxury bag clean!!

Measuring just 850mm in length, TRAMPA’s CARVER DECK is the perfect balance between being small enough to take on a bus, while still feeling substantial & stable under your feet at speed.

With 35° tips, Carve Decks have the same flex & ‘pop’ as TRAMPA’s MTB decks, making them the perfect ‘urban-board’ choice for Mountainboarders. Working in conjunction with Mini Spring

READ MORE...

Complete Deck Weight

35° Carve Deck 14 ply 15 ply 16 ply
Blank Deck Weight 2,200g 2,350g 2,500g
Component Weight 5,645g 5,645g 5,645g
Complete Deck Weight 7.8 kg 8.0 kg 8.1 kg

Component Weights

Mini SPRING Trucks - Unreal carving experience1,318g
Gummies Custom HYPA SUPERSTAR or MEGASTAR Longboard Wheel1,800g
Custom 12mm ATB Bearings with 9.525mm Bearing Reducer Sleeves190g
MkII GUMMIES CARVEBOARD Motormount & 44T Pulley Kit & Motor - SINGLE1,257g
The most Amazing TRAMPA VESC 6 MkV162g
BEAST Box options for CARVEBOARDS 6 - 12Amp 553g
BULL BARS for CARVE BOARDS 248g
Cable Kit for 16A BIGGEST BEAST Box & 1x VESC 6118g
Total component weight5,645g
Mini SPRING TRAMPA TRUCKS - CNC FORGED Channel Hanger with 9.525mm Axle with precision CNC Baseplate
Custom TRAMPA hub with Gummies 125mm Longboard Wheel Tyre
35° TRAMPA Carve Deck - Drilled, Edged, Fitted with JESSOP Grip tape & a Marine Grade Stainless Steel Countersunk Bolt kit

Blank deck weight chart

35° Carve Deck 14 ply 15 ply 16 ply
Blank Deck Weight 2,200g 2,350g 2,500g
General Flex Rating firm stiff very stiff

This Electric Deck is constructed using the following components & parts...

1x 35° Carve Deck - Drilled, Edged, Gripped & Bolt Kit
2x Mini SPRING Trucks - Unreal carving experience
4x Gummies Custom HYPA SUPERSTAR or MEGASTAR Longboard Wheel
1x Custom 12mm ATB Bearings with 9.525mm Bearing Reducer Sleeves
1x MkII GUMMIES CARVEBOARD Motormount & 44T Pulley Kit & Motor - SINGLE
1x The most Amazing TRAMPA VESC 6 MkV
1x BEAST Box options for CARVEBOARDS 6 - 12Amp
1x BULL BARS for CARVE BOARDS
1x Cable Kit for 16A BIGGEST BEAST Box & 1x VESC 6
1x TRAMPA VESC WAND Remote Control
1x Graupner Ultramat 18 charger capable of charging 2x 6s Batteries at once
1x Luxury Travel Bag - Fits 15º short decks with 8 Inch wheels perfectly
----------------------------------------------------------------------------

CUSTOM Boards by TRAMPA are sold to you Un-Assembled with the absolute bare minimum of compoents associated to it as standard. We do this to firstly keep the unit price down as low as possible & secondly so that Dudes that already have many of the items that come as standard with the LOADED board, (remotes, Bags, charger etc) so that these dudes they dont end up with 2 of basically the same thing... Many of our customers are smart minded with mechanical experience & are often very eager to make the final part of the assembly of the board themselves. By sending the board Semi-assembled means that a Luxury bag is not required for additional protection suring the shipping process, which menas the box we send the un-assembled items in is much smaller, using much less space in the lorry when shi[ing means the shipping is also sometimes considerably cheaper (Depends on the location)...  Making the assembly is not so difficult, any basic experience will of course help, but there are video manuals in the tab above & lets face it, if you ride your E-Mtb properly you will need to maintain it and this will inevitably mean sometime you have to take things apart, so by completeing the final part of assembly yourself means that you get to learn how the board really works and which parts would need more servicing than others, and just generally get a good understanding of the board all round.....

----------------------------------------------------------------------------

BATTERIES ARE NOT INCLUDED in the sale in the majority of the products that TRAMPABOARDS Ltd sells. Batteries are expensive to purchase & as they can be deemed as dangerous can very difficult to ship, especially internationally. 
We realised this long ago & decided to incoporate the problem into our design. We realised that although its a bit of a pain in the ass to have to purchase the cells seperatly, its far easier, less complicated & less expensive on the shipping side of things & lets face it there are plenty of companies specialising in the distribution of the cells all around the world all selling them much cheaper than what we could supply them, so in an attempt to side step the shipping problems & save you some cash, that in most cases its up to you to understand the different cell options, resource what us avaiable to you & for you too finally purchase them yourself locally.
SO,
Unless you are a UK customer (or it maybe a customer that can receive a delivery by raod so maybe some EU Countries also soon), in most instances, batteries need to be purchased separately by the customer.
Batteries are in huge demand as there has been huge growth in all electrical products on the market, specially in the DIY side of things which is kind of where the TRAMPA BOARD position's intself in the market... So in our design we offer alternative solutions to be able to power your board using Li-Po of Li-Ion cells... 
There are links to batteries that fit all the boxes here & Depending on how far you wish to go on a single charge will determine what cells you should fit.
As a guide & roughly speaking, 1000mAh (1Ah) is roughly the equivalent to 1 mile of average riding, this is very factor dependant & there are many factors determining the outcome such as, Wheel size & tyre pressure, road surface, the weight of rider, the rate of acceleration, & the top speed they cruise at, the gradients the boards are being ridden on & of course the gearing selection of the rider....
Using the different sized Battery boxes will give varying battery options that can fit the space. In the Classic Monster Box its possible to get upto 22A cells fitted into the box, alternatively that same box will fit TRAMPA's 21A Cell Pack. Classic MONSTER Boxes can be fitted to any size Deck, but if you want the furthest range then you need to fit the MASSIVE MONSTER Box, this is capable of fitting the 21700 12s7p cell pack & using the best cells out there capable of 35Ah of range.
If you are a UK or Customer it is now possible to purchase the 18650 or 21700 cells for the Cell Packs from TRAMPA.

----------------------------------------------------------------------------

WARNING!!!
Mountain-Boarding, Long-Boarding, Electric Mountain Boarding, Kite-boarding, Skate-boarding, infact any version of boarding of any kind, is inherently dangerous. Accidents are deemed as 'part of the fun' & are most likely inevitable.
To limit injury in the event of an accident, it is advised that you should wear as much protective clothing as you can bare to wear in an attempt to protect yourself from injury. When miss-used all kinds of exceptional injuries can happen, including death in rare instances, so always take care & never takes risks if you are not prepared to bare the consequences. You, the rider, is & are 100% fully responsible for your actions & or any accidents that may occur from riding any TRAMPA BOARD.

----------------------------------------------------------------------------

We advise that you never ride on the roads & most importantly, if you do ride on roads that you always ride well away from any traffic. Hitting a car, bus or Lorry whilst riding a skateboard will most likely result in death so we advise you dont do it. Anyway in most countries around the world it is still illegal to ride the devices we sell on the roads or highways & it has been herd of that crime busting Police from all around the world, do in fact have the power to even confiscate your device, so always be respectful when negotiating with the authorities over legislation of whats right or wrong & your right to ride the roads.... Here in the Uk we have no rights to ride on the roads so let that be a warning.

If there is no cycle path for you to ride then please choose the sidewalk or pavement instead of the road & then take your time & steer well clear of anything thats moving... Give way to all pedestrians, most of them have ear ohones in & do not hear you coming so go steady and dont startle by wizzing past them closely & in particular when riding off road look out for, give priority too & give plenty of space to pass dog walkers as they often have an excited animal pleased to see you at the end of a tether, which of course can easily get tangled with you & your equipment & well, lets face it we don't want to hurt the doggie, upset the waker or hurt the rider & where always possible stay well away from all/any moving traffic. Always expect the worst scenario to happen in all cases as vehicle drivers will always win on who comes off best after a collision if competing to be in the same space at the same time, so we beg you to please never take a risk, its just not worth it.

----------------------------------------------------------------------------

Always ride with as much impact protect equipment as you can possibly bare to wear, accidents are inevitable & you are 100% responsible for your own safety at all time, so please check your board often for anything broken or loose & take care as you proceed on the board as these things are very powerful, dangerous in the wrong hands....!!!

What Ply deck do you require...?
What Ply deck do you require...?

8.5-69 Original 14ply SOLID Carve - FIRM
8.5-69 Original 14ply SOLID Carve - FIRM

8.5-69 Original 15ply SOLID Carve - STIFF
8.5-69 Original 15ply SOLID Carve - STIFF

8.5-69 Original 16ply SOLID Carve - STIFFEST
8.5-69 Original 16ply SOLID Carve - STIFFEST

8.5-69 Original 14ply HOLYPRO Carve - FIRM (+£25)
8.5-69 Original 14ply HOLYPRO Carve - FIRM (+£25)

8.5-69 Original 15ply HOLYPRO Carve - STIFF (+£25)
8.5-69 Original 15ply HOLYPRO Carve - STIFF (+£25)

8.5-69 Original 16ply HOLYPRO Carve - STIFFEST (+£25)
8.5-69 Original 16ply HOLYPRO Carve - STIFFEST (+£25)

Do you want INFINITY, VERTIGO or ULTIMATE Trucks?
Do you want INFINITY, VERTIGO or ULTIMATE Trucks?

Mini INFINITY Hanger - 9.525mm SOLID axles
Mini INFINITY Hanger - 9.525mm SOLID axles

Mini VERTIGO Hanger - 9.525mm HOLLOW Axles (+£50)
Mini VERTIGO Hanger - 9.525mm HOLLOW Axles (+£50)

Mini ULTIMATE Hanger - 9.525mm TITANIUM Axles (+£75)
Mini ULTIMATE Hanger - 9.525mm TITANIUM Axles (+£75)

Do you want HYPA, SUPERSTAR or MEGASTAR hubs?
Do you want HYPA, SUPERSTAR or MEGASTAR hubs?

6 Spoke HYPA Hubs
6 Spoke HYPA Hubs

5 Spoke SUPERSTAR Hubs (+£40)
5 Spoke SUPERSTAR Hubs (+£40)

5 spoke 8 Inch OFF-SET MEGASTAR hubs (+£100)
5 spoke 8 Inch OFF-SET MEGASTAR hubs (+£100)

5 spoke 8 Inch CENTRE-SET MEGASTAR hubs (+£100)
5 spoke 8 Inch CENTRE-SET MEGASTAR hubs (+£100)

Quantity required:
We have enough parts to make…  
From £1,300 - each

Excluding VAT

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......


 

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon