This site is best viewed in Google Chrome, Firefox or Safari. The site uses cookies for e-commerce functionality. Click here to remove this message.

Mountainboard PRO Belt Drive TWIN Motor Mounts, Motors & Precision VERTIGO Truck

Mountainboard PRO Belt Drive TWIN Motor Mounts, Motors & Precision VERTIGO Truck Mountainboard PRO Belt Drive TWIN Motor Mounts with Motor Protection housings - NO Motors CNC Precision E-MTB Truck  - 16 inch wide with 12mm SOLID Axles with Infinity Baseplate & Steel kingpin TRAMPA Custom DC Motor 6364/6376
RRP
£550
exc tax

TRAMPA's Generation III PRO BELT DRIVE Motor Mount is a work of art! Made predominantly from T6 Aluminium, every piece has been precision made to give simple assembly & maximum performance.

The Pro Belt Drive Motor Mount will give you the same kind of performance as experienced when riding an Enduro Motor bike, it uses a lower gearing ratio of 4.71:1 giving a higher top speed when compared to the Spur Gear Drive setup - which has a higher gear ration of 5.9:1 (for better acceleration).

The Gen III Pro Belt Drive Motor Mount will only fit to Precision CNC Hangers, using TRAMPA's special Conical Clamping system to securely attach onto the Hanger. The Assembly of any of the Pro Motor Mounts is incredibly sturdy & robust; perfect for the rough terrain they’ll be ripping across.

Accommodating a 66 Tooth Slave pulley, it is possible to adjust your gearing by swapping between 13, 14 or 15 tooth Motor pulleys.  13 tooth motor pulleys are perfect for hill climbing, whereas 15 tooth pulleys will achieve a higher top speed, & 14s are a nice balance between the two.

You can further adjust the performance by changing the Rear Drive wheel size. Changing from 8” to 9” or 10“ Tyres has a massive effect on the performance of the board. Check out the Pro Belt gearing chart to see estimated top speeds of different tyre & pulley combinations.

It is only possible to fit the TRAMPA 5 Spoke Hubs to Pro Drive Slave Pulleys. This means the 5-Spoke Superstar & Megastar wheels fit no problem. However it is only possible to run 8 – 10 inch tyres on the Pro Drives, due to low clearance around the housing tubs.

Enclosed within the Motor Mount tub is the Belt Tension Roller - a Bearing Mounted in Aluminium housing, that guides the belt into the optimum position/tension, to maintain the max amount of grip between the belt & the pulley.

Its possible a belt can snap for a variety of reasons. If you’re the kind of rider that likes to go off into the wilderness, then you should always ride with a couple of spare belts (when one snaps, chances are the other isn’t far off).  TRAMPA's Pro Belt Drive utilises two special cut-outs that ‘ejects’ broken belts from the housing – slimming the chances of snapped belts jamming up the Motor Pulley.

The best way to prevent a belt snap is to check over & replace the Pulleys & belts on a semi-regular basis - BEFORE they have chance to fail on you. Riding, accelerating & braking hard will wear out your belts & pulleys faster. We recommend you service your board every three rides, or after any particularly tough ride. Check the hardware is tight, the belts aren’t worn, & for any damage, particularly to the motor mounts/trucks. Ensure the tub is free from any dust/dirt. Servicing your board is important for keeping it running smoothly, as well as for your safety when riding.

CUSTOM Spring Truck Baseplate - Extruded T6 Aluminum Anodised & CNC precision Milled

The  INFINITY Baseplate will fit to all of the TRAMPA Spring Truck Hangers but is designed specifically to work in conjunction with the Mini Spring Hanger as it houses a NEW Dual Spring Adjuster position! When the Springs are moved to the new inside position, the new location allows the rider to turn the board very very easily, making it perfect for fast carve riding on all kinds of terrain. You can see the new & growing TRAMPA STREET CARVER range of products here...

The  INFINITY Baseplate is, as its name suggests, designed & built to last forever! Aircraft grade 6061 Aluminum is forced through a Die to create our re-enforced extruded profile. Extruding Aluminum ensures consistent high quality strength. Once Extruded the Baseplate is T6 Heat Treated. Heat treating extruded aluminum fuses the molecules even closer together making it as strong as possible, enabling the INFINITY Baseplate to easily cope with the extreme stresses of all types of off road boarding.

Once Heat Treated, the profile has its fixing holes punched into position & then its Bead Polished in preparation to be Anodised Silver. Once the colour has dried, the Baseplate is then returned to the factory for the precision CNC Machine to accurately mill the Kingpin holes, giving the exact precision required for constructing the Truck.

M6 x 30mm Countersunk Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

 

- 6-8s Battery Box

- 8-10s Battery Box

-Beast Boxes

 

 

M5 x 12mm Countersunk Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-Ratchet Bindings

-Camlock Bindings

-Heelstraps

M3 x 16mm Countersunk Head Bolt Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

MONSTER BATTERY BOX

M5 x 20mm Regular Hex Head Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 4mm Grub Screw M4 x 4mm Motor Pulley Grub Screw - Connects the Motor Pulley onto the Motor Axle Shaft

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 16mm Socket Capped Head TORX Bolt ISO 4762 Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt DIN6912 Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M3.5x12 EJOT Bolt. TORX DOME Headed Used to secure the Motor PROTECTION COVERS fitting to SPUR GEAR DRIVE Motor Mounts, this bolt cuts its own thread!!!

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

Custom TRAMPA DAMPA


 

The TRAMPA DAMPA is a Urethane Elastomer that fits inside the Spring of a Truck. Its purpose is to support the Spring & give extra resistance during steering. Its clever design has three balls stacked & connected on-top of each other. The middle ball is slightly fatter than the outer two, during steering they all compress against each other giving greater feed back in your turns. This stacked design gives a fantastic progressive feel to steering.

By varying the SHORE DUROMETER (Rubber Hardness) strength of the Urethane mixture, we can control the amout of movement in the DAMPA. This in turn allows the rider to custom tune the resistance of their steering perfect to their requirements. The spheres of the DAMPA fit perfectly into the cup of the specially made TRAMPA SPRING RETAINER which is the part that locates & locks the Spring in the the TRAMPA SPRING TRUCKSand they instantly start to work with the slightest movement from the rider. TRAMPA DAMPA's work in harmony with the rider, supplying the perfect amount of steering resistance whilst eliminating all chances of speed wobble. Now available in 5 different steering resistance's for all levels of rider out there, Orange DAMPA's are for easy steering, whilst White DAMPA's are for the totally committed! 

Turning the Spring Adjuster clockwise pre-loads the tension in the Spring and Dampa. This can be adjusted on the fly to suit the terrain & conditions. Turning the spring adjuster too much will put pressure on the Dampa & eventually it may split. Rather than putting too much pressure into the Dampa, consider up-grading the Dampa to a harderShore Durometer as this will most likely increase your perfomace than overtightening a Dampa thats not stiff enough for you. Please use the table below for guide.

 

COLOUR

Stiffness

Shore

Suitability Guide

ORANGE

Super Soft

55

Light Riders / Crazy Carvers!

PINK

Soft

60

Beginner Carvers

YELLOW

Average

65

Beginner / Intermediate

GREEN

Average (75kg+)

75

Intermediate / Adult sized rider

RED

Firm

80

Advancing rider / Teenage Freestyler

BLUE

Stiff

85

Fast & Advanced Freestyle Rider

WHITE

Stiffest

90

For the Insane only!

415 long x 16mm wide High Torque Drive (HTD) 5M (5mm Tooth Space) High Power (HP) STRONGBELT for 2020 Mountainboard Pro Motor Mounts

This ia 460mm long x 15mm wide High Torque Drive (HTD) Re-enforced Rubber Belt, which has 5mm Tooth Spacing (5M). This Belt is High Power rated (HP) & arguably over engineered for our application as the belt is made in Germany by the world famous company called STRONGBELT, who usually supply into heavy industry public sector applications which demand much more stringent requirements of any electric skateboard! This belt is used to transfer the power from the Motor & Motor Pulley into power at the rear wheels of a TRAMPA Electric Mountainboard.

TRAMPA opted to set a new standard in E-Skating, becoming the first in the world to fit to all of its E-Boards, a 15mm wide TRANSMISSON BELT. Our standard 15mm belt is almost double the width of nearly all other E-Sk8's out there, they tend to use a flimsy off the shelf 9mm transmission belt which are prone to stretch, slip & ultimately snap. Using a re-enforced 15mm wide High Power Belt reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. When accelerating or engine breaking (KERS), even from a standing start the STRONGBELT power is smooth & does not slip, or strain the motor, it does a damn gooood job!.....

STRONGBELT, as their name suggests, is a Heavy Industry German Brand that usually supplies the likes of Train manufacturers where serious levels of quality with no excuses on failure are expected from the product, as failure for such an item is serious & may result in death! STRONGBELT weave KEVLAR into their Pulley Belts, Kevlar is one of the strongest fibers known to man, its often added into materials to gain extra strength.... STRONGBELT have the best reputation in the Power Transmission Industry for NO stretching or snapping & we have high expectations from this quality item. 

These extra quality details in the production of our electronic motor drives, provides the maximum responsiveness achievable whilst maintaining a super smooth power delivery to the rider at all times. 

Belt Tension Roller Housing for 15mm Belts - SILVER

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

Made from T6 Heat-treated Aluminium, these Belt Tension Rollers are to designed to house a premium TRAMPA 608 BEARING, ensuring a smooth and consistent roll while tensioning the belts. Used with 15mm belts on PRO BELT or OPEN BELT DRIVE, as well as MKII Urban Carve Motor Mounts.

Stainless steel SPACER NUT for mounting the 15mm Belt Tensioner

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

These Spacer-Axles have two functions, correctly positioning the 15mm Tension Roller, as well as providing the housed 608 bearing a snug-fitting axle to spin freely on.

MkII Motor Protection Fan for cooling Motor runnning temps within the MKII Motor Protection Housing

Pairing with the new MKII Delrin Motor Housings, these fans secure to the ends of 6376 Motors, creating a cooling airflow around the motors - reducing running motor temp, and increasing efficiency!

After many different designs and prototypes, this shape has proved the most efficient at creating an airflow that made a real difference to the motors’ performance.
Attaches to the end of motors using 5x M3x16mm Countersunk bolts.

PRO Belt Motor Mount Aluminum TUB - V3

CNC’d from a solid block of T6 heat-treated Aluminium, the V3 PRO BELT MOTOR MOUNT TUB is built around keeping the drive train securely & accurately attached, while running as smoothly as possible. Paired with the specially designed CNC’d COVER, the completed tub keeps the elements outs, the gears & belts clean & dry, & the whole board running smoothly.

Attaching T6 Aluminium BASH GUARDS (left & rightensures the Tub will survive every knock & bump the drive system is bound to receive on a ride.
Special cutouts on the sides of tub allow snapped belts to be ejected out & away from the drive train, preventing any jammed gears or wheel lock.

The Tub is perfectly symmetrical allowing it to slide onto left or right drive trains.

PRO Belt Motor Mount ALUMINIUM Panel - V3

The Pro Belt Tub Cover is crucial to keeping your drive system free of dirt & debris. CNC’d from Premium Aluminium, giving it the perfect weight-to-strength ratio, the cover slots tightly over the Pro Belt Tub, perfectly sealing off the drive system.

PRO Belt Motor Mount Bash Guard V3 - LEFT

Made using hardened steel, the PRO BELT bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the left drivetrain.

PRO Belt Motor Mount Bash Guard V3 - RIGHT

Made using hardened steel, the PRO BELT bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the right drivetrain.

PRO Belt Motor Connector & press fitted 608 Bearing

Housing a precision bearing for Motor Axle Support the PRO BELT DRIVE Motor Adaptor is used for attaching the motor securely to the drivetrain.
Precision CNC’d from hardened steel, the Motor Adaptor also allows for the use of PRO MOTOR HOUSING.

PRO Mountainboard Motor Mount V-Ring TUB Seals - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

PRO Mountainboard Motor Mount Rubber pad for Conical Clamps - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

66 Tooth Slave Pulley with Pressed bearing - Fits to 8 inch wheels in V2 & V3 PRO Motor Mounts

TRAMPA's 66 Tooth Pro Motor Mount Slave Pulley fits to any of TRAMPA's 8 Inch off road wheels when connecting into the Mountainboard PRO Motor Mount system. The 66 tooth Pulley has been precision milled from super-light-weight & mega strong Heat Treated T6 Aluminum. The pulleys teeth stand 5mm tall, this is the same size teeth as that found on TRAMPA's 15mm wide 'Strongbelt' & when TRAMPA's 460x15mm Premium Strongbelt is wrapped around the pulleys & the belt tension facility has been screwed down the connection between the teeth & the belt becomes so strong it has what we call HIGH TORQUE DRIVE (HTD)HTD ensures all of the motors Torque is forced through the pulleys to the wheels & when coupled with the amazing VESC 6 & 12s Battery power provides instant smooth unreal Power on tap to the rider!

This 66 tooth Pro Mount Slave Pulley is capable of connecting to all of the wheels (7, 8 & 9 Inch) in the TRAMPA range but we (TRAMPA) only use it when assembling 8 inch TRAMPA wheels into the TRAMPA Pro Motor Mounts

But with the use of some very special Threaded Hex Spacers & Socket capped Bolts the 66 Tooth Pro Mount Slave Wheel connects directly to any of the 7 or 8 Inch SUPERSTAR or HYPA Wheel s& very uniquely also into the 3 spoke PRIMO 9 Inch Wheel as well - 1 pulley, 3 uses.... :-)

TRAMPA's special 66 tooth Pro Mount Slave Wheel works in conjunction with all & any of the 13, 14 or 15 tooth Motor Pulley in the range. Changing your Motor Pulley will drastically alter the performance & characteristics of your ride... 13 Tooth is best for Hill Climbing whilst 15 Tooth is best for high speed, 14 tooth will give you all round performance...

To connect to HYPA hubs you'll need 6x 17x4mm Threaded Hex spacers
To connect to SUPERSTAR hubs you'll need 5x 15x4mm Threaded Hex spacers

 

13 Tooth 15mm BLACK STEEL Motor Pulley Fits 8mm Motor Axles with 15mm Belts - Best for HILLS

TRAMPA's 13 Tooth Motor Pulley Wheel connects directly to the Motor Axle & is secured into position using a Magnetic Fixing Key & 4mm Locking Grub Screw.

This custom made Motor Pulley Wheel uses the German Made & 15mm wide STRONGBELT which should never stretch or break whilst at the same time providing a very smooth power delivery to the user even from a standing start....

Changing your Motor Pulley &/or Drive pulley wheels will drastically change the performance of your ride... :-)

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x8mm

TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.

TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....

CUSTOM Precision Hanger using 12mm Axles - 16.5 Inch Wide

The ATB INFINITY HANGER is time proven as being the strongest ATB SPRING TRUCK Hanger on the market! Ensuring we deliver the maximum strength possible the hanger body of all of the Spring Trucks in the TRAMPA range are made from super strong FORGED ALUMINUM & this INFINITY hanger is one solid entity with no weight saving cut outs or or fancy Axels & weighs in as the Strongest!

The Infinity Hanger is machined on the underside to allow countersunk bolts to push through & position the springs in the correct locations. The Infinity ATB Trucks has been given 2 Spring position settings, allowing Inside spring position setting for easy/fast carve steering & outside spring position for larger sized or high speed thrill seeker riders!

The Infinity ATB Hanger is drilled & machine fitted with Heat Treated 12mm SOLID STEEL Axles. HEAT TREATING the steel axles makes them substantially stronger & far more resistant to impact - perfect for larger sized adult riders. 12mm Solid Steel Axles are slightly heavier than alternatives displayed on the TRAMPA website, but they are by far the strongest Axles in the TRAMPA range. Once the 12mm Solid Axles are machine fitted the INFINITY hanger measures 16 Inches at its widest points & when any of the 5, 6, 7 or even 8 Inch HYPA or SUPERSTAR wheels are fitted to the Hanger, the board has a center wheel base width (Center point of contact to the floor) of 14 Inches.

CNC milling usually guarantees precision work & that's why the Infinity hanger has had the Kingpin holes CNC machined insuring the Kingpin Holes are accurately placed guarantee's the best performance to the rider as well as making the truck easy to assembly & simple to service. Before the CNC work is completed the ATB Infinity Hanger is Anodised BLACK for metal protection.

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

7/16ths Nut - Marine Grade Stainless steel Nylock Axle HALF nut (W7/16-20T UNF) - Fits to 12mm Axles

This very special 7/16ths of an inch Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut.. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore further reducing weight in the Truck! A few Grams here & a few grams there soon adds up & makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area, where a few grams makes all the difference...

This very special 3/8ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W7/16 - 20T - UNF. This Nut is used to hold the wheels onto the axles of the Spring Trucks fitted with 12mm axles. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 16mm or 5/8thths of an Inch spanner to tighten / loosen the Nut onto the Axle or Kingpin. Do not overtighten the nut & make sure the wheel can spin freely but does not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

Wheel support spacer for all TRAMPA Wheels on 12mm ATB Axles - CNC precision 12mm x 16mm x 18.2mm

This special Spacer measures 12mm (id) x 16mm (od) x 18.2mm (long) & has 2 uses!. It is firstly known as the Bearing Support Spacer as this Spacer fits between the Bearings of a 6 Spoked HYPA Hub, (when mounting the HYPA wheel onto 12mm Axles) & secondly it is also known as the AXLE SUPPORT SPACER as this spacer is also used to position any of the TRAMPA wheels in the perfect position onto the axles of 12mm TRAMPA Spring trucks....

TRAMPA spacers are produced as one long tube. The Tube is Heat Treated to gain extra strength & is then Bead Polished to give the metal extra surface protection & a shiny best appearance. The tube is then cut to the exact length for precision mounting. 

Custom Colour Spring - Powdercoated Sprung Steel Steering Springs

TRAMPA's SPRINGS are coiled to precision & fit into the TRAMPA Spring Trucks perfectly. They easily squeeze into the space between the Baseplate & Hanger & being made to measure they are firstly very easy to fit with no clamps or tools required to squueze them into position & secondly to be super responsive to the rider.!  Once the spring assembly is fitted correctly the steering resistance is taken up instantly!

Our Springs have been designed to work in perfect harmony with the TRAMPA DAMPA's & TRAMPA SPRING RETAINER providing maximum performance from the "Spring assembly" to the rider. The DAMPA's drop into the SPRING & the SPRING RETAINERS seal the ends of the spring, holding the DAMPA in exact position to be pre-loaded & squeezed into the truck. Using just a little bit of muscle, squeeze the loaded spring into the truck, then lock the spring into position using the Spring Adjuster & M5 x 12mm Countersunk Bolt. The TRAMPA spring Truck steering system is highly responsive & totally customisable by interchanging the DAMPA's to harder Urethane. Other Mountain Board brands springs will not fit the TRAMPA Trucks as they are a different in dimension.

TRAMPA Springs are available in a selection of Powder-coated colours for good looks & of course for best surface coating protection & this one comes to you in Powder Coated Black. 

Spring Retainer - Specially designed to work in harmony with the Dampa & spring

TRAMPA's very own & very special re-enforced Spring retainer. Specifically shaped to fit tightly inside the TRAMPA springs & snugly hold the Trampa Dampa in the exact position to give precision steering to the rider. Made by Injection Moulding using original Dupont Materials, with an extra wide Marine-Grade Stainless Steel Flanged Insert seated internally, re-enforcing the Retainer. The Extra Strength of the re-enforced flange, eliminates the need for a very fiddly fitting washer, that is still found in the MBS and Scrub boards today.

Designed to work in harmony with the TRAMPA spring and TRAMPA Dampa to help create immediate resistance from your steering system. With TRAMPA Embossed around the rim of the retainer - you'll have performance with pimpness!

Spring Adjuster - Marine Grade Stainless Steel

TRAMPA's very own & very special SPRING ADJUSTER is made using A4 MARINE GRADE STAINLESS STEEL & is guaranteed never to rust on you! The Spring adjuster is fitted to the trucks once the springs have been pushed into position. The spring adjuster pre-tensions the steering suitable for the rider’s requirements. We designed the Spring Adjuster to be slightly shorter in length than other brands’, to avoid  the tip of the adjuster poking through the internal of the Spring Retainer, and interfering with the performance of the DAMPA located on the inside of the Retainer.

Should you need extra resistance from your steering because you wish to ride fast, or if you need more steering because the course is twisty, then you can very easily & quickly adjust the resistance of your steering by simply turning the spring adjuster in the correct direction. To get the most out of your trucks on changeable terrain, simply use a 4mm Allen Key to make your adjustments. Winding the Spring Adjuster clockwise increases the steering resistance, which in turn restricts wobble at high speed. Turning the Adjuster anti-clockwise loosens the steering allowing a more carvey ride.  

DO NOT over tighten your Spring Adjuster, as this may crush your DAMPA. If you need more steering resistance upgrade your DAMPA's & do not over tighten!

TRAMPA's Generation III PRO BELT DRIVE Motor Mount is a work of art! Made predominantly from T6 Aluminium, every piece has been precision made to give simple assembly & maximum performance.

The Pro Belt Drive Motor Mount will give you the same kind of performance as experienced when riding an Enduro Motor bike, it uses a lower gearing ratio of 4.71:1 giving a higher top speed when compared to the Spur Gear Drive setup - which has a higher gear ration of 5.9:1 (for better acceleration).

The Gen III Pro Belt Drive Motor Mount will only fit to Precision CNC Hangers, using TRAMPA's special Conical Clamping system to securely attach onto the Hanger. The Assembly of any of the Pro Motor Mounts is incredibly sturdy & robust; perfect for the rough terrain they’ll be ripping across.

Accommodating a 66 Tooth Slave pulley, it is possible to adjust your gearing by swapping between 13, 14 or 15 tooth Motor pulleys.  13 tooth motor pulleys are perfect for hill climbing, whereas 15 tooth pulleys will achieve a higher top speed, & 14s are a nice balance between the two.

You can further adjust the performance by changing the Rear Drive wheel size. Changing from 8” to 9” or 10“ Tyres has a massive effect on the performance of the board. Check out the Pro Belt gearing chart to see estimated top speeds of different tyre & pulley combinations.

It is only possible to fit the TRAMPA 5 Spoke Hubs to Pro Drive Slave Pulleys. This means the 5-Spoke Superstar & Megastar wheels fit no problem. However it is only possible to run 8 – 10 inch tyres on the Pro Drives, due to low clearance around the housing tubs.

Enclosed within the Motor Mount tub is the Belt Tension Roller - a Bearing Mounted in Aluminium housing, that guides the belt into the optimum position/tension, to maintain the max amount of grip between the belt & the pulley.

Its possible a belt can snap for a variety of reasons. If you’re the kind of rider that likes to go off into the wilderness, then you should always ride with a couple of spare belts (when one snaps, chances are the other isn’t far off).  TRAMPA's Pro Belt Drive utilises two special cut-outs that ‘ejects’ broken belts from the housing – slimming the chances of snapped belts jamming up the Motor Pulley.

The best way to prevent a belt snap is to check over & replace the Pulleys & belts on a semi-regular basis - BEFORE they have chance to fail on you. Riding, accelerating & braking hard will wear out your belts & pulleys faster. We recommend you service your board every three rides, or after any particularly tough ride. Check the hardware is tight, the belts aren’t worn, & for any damage, particularly to the motor mounts/trucks. Ensure the tub is free from any dust/dirt. Servicing your board is important for keeping it running smoothly, as well as for your safety when riding.

In this kit you get the following items -
2x 2x ATB CNC Spring Truck PRO Motor Mount CONNECTOR
2x 2x ATB CNC Spring Truck PRO Motor Mount BACK PLATE
2x 2x Anti Vibration Rubber pads fitting in the Conical Clamps
8x 8x M5x18 Marine Grade Stainless Steel HEX Head Bolts
8x 8x M5 Marine Grade Stainless Steel Washers
2x T6 CNC ALUMINUM Tub
2x T6 ALUMINUM Tub Enclosure
1x ALUMINUM Bashguard for LEFT Side
1x ALUMINUM Bashguard for RIGHT Side
4x M4x16mm TORX Socket Cap Bolt - Bash Guard to tub
2x Motor Adaptor Plate with Factory fitted Bearing Support
2x 66 Tooth Pro Belt Drive Slave Pulleys
2x Rubber V-Ring protective Tub Seal
2x 470mm 15mm wide 5m Teeth STRONGBELT
2x Belt TENSION ROLLER - Bearing in Housing
2x Belt Tension Roller AXLE PIN
2x M6x30mm Countersunk Allen Key Bolt for Belt tensioner
2x M6 WASHERS for securing the Belt Tensioner
2x M6 Nut Secures Belt Tensioner in position
2x Custom choice of 13, 14 or 15 Tooth Motor Pulley
4x M4x4mm Grub Screw for securing the Motor Pulleys
4x 3x3x8mm Keyway fot locking the Pulley to the Motor Shaft
22x M4x10mm BUTTON Headed TORX bolts holding everything together
2x Super strong DELRIN Plastic Motor Protection HOUSING Open Ended
2x MkII Motor protection Cover MESH FILTER - SILVER
12x M3.5x12 EJOT TORX DOME Headed Bolts for SGD Motor Protection
2x MkII Motor Protection Fan for cooling Motor runnning temps within the MKII Motor Protection Housing
10x M3 x 16mm Countersunk Bolt - Marine Grade Stainless Steel
1x CUSTOM ATB Precision Hanger using 12mm Axles - 16.5 Inch Wide
2x 12 x 18.2mm Wheel Support Spacer for all TRAMPA Wheels on 12mm ATB Axles
2x 7/16ths (12mm) Marine Grade Stainless steel Nylock Axle HALF nut
1x CUSTOM TRAMPA Spring Truck Baseplate's
Kingpin Bushings 2.5mm Base - for Spring Trucks
King Pin bushings 2mm Base for Spring Trucks
Custom Kingpin for Spring Trucks - M8x80mm Nikle Plated, Stainless Steel or TITANIUM
M6 Nut - Marine Grade Stainless steel Nylock nut
M6 Washer Form C - Marine Grade Stainless Steel
M8 x 1.5mm Form B Kingpin Washer Marine Grade Stainless steel
1x Complete Spring kit for 1x Truck
2x 6376 TWIN Motor lushness! FIXED
Weight: 4,805g
What colour Baseplate do you require...?
What colour Baseplate do you require...?

BLACK Anodised with SILVER logo VERTIGO Baseplate
BLACK Anodised with SILVER logo VERTIGO Baseplate

BLUE Anodised with BLACK logo VERTIGO Baseplate - OUT OF STOCK
BLUE Anodised with BLACK logo VERTIGO Baseplate  - OUT OF STOCK

BRONZE Anodised with BLACK logo VERTIGO Baseplate
BRONZE Anodised with BLACK logo VERTIGO Baseplate

GOLD Anodised with BLACK logo VERTIGO Baseplate
GOLD Anodised with BLACK logo VERTIGO Baseplate

GREEN Anodised with BLACK logo VERTIGO Baseplate
GREEN Anodised with BLACK logo VERTIGO Baseplate

GUNMETAL Anodised with BLACK logo VERTIGO Baseplate
GUNMETAL Anodised with BLACK logo VERTIGO Baseplate

NAVY Powdercoated with BLACK logo VERTIGO Baseplate
NAVY Powdercoated with BLACK logo VERTIGO Baseplate

PINK Anodised with BLACK logo VERTIGO Baseplate
PINK Anodised with BLACK logo VERTIGO Baseplate

PURPLE Anodised with BLACK logo VERTIGO Baseplate
PURPLE Anodised with BLACK logo VERTIGO Baseplate

RED Anodised with BLACK logo VERTIGO Baseplate - OUT OF STOCK
RED Anodised with BLACK logo VERTIGO Baseplate  - OUT OF STOCK

RED Powdercoated with BLACK logo VERTIGO Baseplate
RED Powdercoated with BLACK logo VERTIGO Baseplate

SILVER Anodised with BLACK logo INFINITY Baseplate
SILVER Anodised with BLACK logo INFINITY Baseplate

SILVER Anodised with BLACK logo VERTIGO Baseplate - OUT OF STOCK
SILVER Anodised with BLACK logo VERTIGO Baseplate  - OUT OF STOCK

WHITE Powdercoated with BLACK logo VERTIGO Baseplate
WHITE Powdercoated with BLACK logo VERTIGO Baseplate

WHITE Powdercoated with BLUE logo VERTIGO Baseplate
WHITE Powdercoated with BLUE logo VERTIGO Baseplate

WHITE Powdercoated with RED logo VERTIGO Baseplate
WHITE Powdercoated with RED logo VERTIGO Baseplate

What size Motor Pulleys you would like?
What size Motor Pulleys you would like?

13 Tooth 15mm wide - Great Hill Climber
13 Tooth 15mm wide - Great Hill Climber

14 Tooth 15mm wide - All Round gearing
14 Tooth 15mm wide - All Round gearing

15 Tooth 15mm wide - Great Top Speed
15 Tooth 15mm wide - Great Top Speed

What size Motor you would like...
What size Motor you would like...

6364 160Kv TRAMPA Motor - Even more amazing speed!
6364 160Kv TRAMPA Motor - Even more amazing speed!

6376 160Kv TRAMPA Motor - Only for the Insane! (+£50)
6376 160Kv TRAMPA Motor - Only for the Insane! (+£50)

6376 185Kv Motor - The fastest yet!! (+£50)
6376 185Kv Motor - The fastest yet!! (+£50)

Quantity required:
We have enough parts to make…  
RRP £550 - for the complete set

Excluding VAT

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon