This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

Classic MONSTER Box Installed with an 18650 PCB Pack BUT NO VESC & NO CELLS

Classic MONSTER Box MkV supplied with a 18650 PCB based Battery Pack with Integrated Battery Management System (BMS) - NO VESC & NO Cells Classic MONSTER Box with Mounting Panel to fit NO VESC 6 18650 PCB Pack with integrated BMS - Fits Classic MONSTER box & 84 x 18650 cells to give 21,000 mAh (21A) of range - Works in Conjunction with 2x VESC 6
RRP
£550+

TRAMPA's CLASSIC MONSTER Box is capable of housing up to 2x 6s 22Ah Li-Po Cells & 2x VESC 6 speed controllers at the same time.

TRAMPA's different sized Monster boxes are all made using 2mm & 4mm thick GR4 Re-enforced Glass Fiber panels. The Base & Split Lid panels have been CNC machined with a 2.1mm groove to allow the 2mm thick side panels to slot in & inter-connect perfectly, giving a very strong & tight construction to the box. The box is held together with Anodised Aluminum Hex Spacers which use Stainless Steel Dome Headed TORX Bolts that in turn use lock-tite for permenant connection are screwed through the base of the box, whilst Stainless Steel Countersunk TORX Bolts mounted in a Anodised decorative washers are then used to screw the lid down into the Hex Spacers giving an incredibly neat tight strong & smart finish to the assembly.

As the Box uses the latest Split lid & Inspection pit, it is possible to undo the Countersunk Lid Bolts & remove either the Battery Lid-Side or the VESC Lid-Side of your box, should you ever wish to remove your batteries or take out a VESC without collapsing the entire box down.

Fitted to the top of the Monster Box is the Inspection Pit. Turning the thumb screw on the top gives you access to the Battery Charge Cable & Balance leads that are pushed through rubber grommets to stop the ingress of moisture & dirt, & preventing you from having to open the entire box to do your charging & balancing. 

The Classic Monster Box connects to a TRAMPA Mountain board deck using a Universal Mount & is top side mounted between the riders feet. The Power Cables for the motors exit the box through water resistant Rubber Grommets from the underside of the box, feeding into the protected grooved channels of the WINGS running under the riders feet, eventually poking out at the rear of the deck where the motors are waiting to be connected.

The MONSTER Box is surface mounted to give maximum ground clearance when riding off road. The majority of TRAMPA products are designed to be ridden off road. When you ar riding off road you need extra clearance or you will get snagged up on anything that protrudes from the ground, bashing your battery box on rocks is not a good idea, plus mounting the box on the surface in the way that we do using the universal mount means we retain 95% of the flex of the deck that the TRAMPA decks are so much famed for.

​When installing your chosen batteries into your MONSTER BOX, it’s a good idea to secure them to the base with Velcro, then pad the area around the batteries with good quality foam. This reduces any ride-ruining-rattling sounds whilst keeping the batteries safe from bouncing around when riding over rough terrain.

If you are running full power using the VESC Speed controllers & want good temperature control then it is worth while considering adding a VESC 6 Heat-Sink or two with your purchase.

The Monster Box is NOT Waterproof. It is at best Splash Proof. If submerged into water then you are in trouble. Its best to avoid puddles as you do not know how deep they are. I use puddles as something to carve around and turn them into something fun, (The TRAMPA Stunt Monkey can jump the puddles!) and if you are using this product in an outside environment when its likely to get covered in mud and splashy water like we do with our Mountainboards, then it is wise practice to protect your equipment & add a Monster Box cover. The Thicker Luxury Monster Box cover is fitted with long pockets down the side to store your WAND Controller or critical tools needed on a ride with a removable 'Velcro' top strip that easily peel off allowing you to get access to the inspection pit without having to remove the entire & potentially muddy cover, which just makes life that bit easier. It is my advise to cover the Luxury cover with the Monster Box Muck off or splash proof cover. The Nylon Splash proof cover adds more moisture & dust protection, and adding them both means you keep your luxury cover as clean as possible, but still have access to the charging & balance cables whilst gaining maximum water proofing protection to your equipment

CLASSIC MONSTER Box MkV 2WD BASE

The Monsterbox Classic MkV Base connects to all vertical panels in a Monster Box Classic or Double Stack Monster Box Classic, provided the adjacent panels are also Mk5. They are used with grommets to allow entry into the box by the phase and sensor cables, and the edges of the box are where the hex spacers mount. Additionally, the base is where any Monsterbox is mounted to the board. In this case that can be done via the standard bushing system or Dogbone mounting system. This panel is only designed to operate with 2 motors.

TRAMPA CLASSIC Monster Box MKV LID - Battery Side

The Monsterbox Classic MkV Lid rests on top of the side and end panels of the Monsterbox Classic MkV and centers the screws into the hex spacers to hold the box together.

TRAMPA CLASSIC Monster Box MKV LID - VESC Side

The Monsterbox Classic MkV VESC Side Lid rests on top of the side and VESC panels of the Monsterbox Classic MkV and centers the screws into the hex spacers to hold the box together. It also acts as an access terminal, allowing you to conduct simple maintenance such as charging and turning your VESCs on and off without opening up the box.

CLASSIC MONSTER Box MkV 2mm SIDE PANEL

The side panel is a structural component of the Monster Box MkV that connects the lids and base of the box together.

TRAMPA CLASSIC Monster Box MkV END Panel

Structural component, like the side panels, to connect the lids and base of a Monster Box MkV together.

TRAMPA CLASSIC Monster Box MkV END Panel

Structural component, like the side panels, to connect the lids and base of a Monster Box MkV together.

TRAMPA CLASSIC Monster Box MKV Inspection Pit

The Inspection Pit allows easy access to balance leads and other items on the Monster Box Classic MkV.

TRAMPA CLASSIC Monster Box MKV Inspection Pit Lid

The Inspection Pit lid covers and secures the Inspection Pit on the Monster Box Classic MkV.

Upper Glass Fibre Panel for 18650 Pack

Lid for 18650 PCB Battery

Lower Glass Fibre Panel for 18650 Pack

Base for 18650 PCB Battery

Cell Spacers for 18650 Battery Pack

Spacer to correctly hold 18650 Cells in PCB Battery pack. 

Universal PCB BRIDGE Cable for PCB GEN I Battery Packs

Universal PCB BRIDGE Cable for PCB Battery Packs

Connects parallel groups from the top and bottom PCBs of a Trampa battery pack to ensure proper balancing.

18mm to 6mm Heat Shrink Cable - BLACK 30cm Strip

Shrink wrap, used for sealing exposed motor cables or contacts after soldering.

This 18 - 6mm Heat Shrink is sold as 1x 30cm  length.

Regaquires a hot heat gun to shrink the wrap.

M3 x 10mm TORX Countersunk Head Bolt Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

BIGGEST Beast Box

M3 x 12mm TORX Countersunk Head Bolt Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

BIGGEST Beast Box

M5 x 10mm TORX Countersunk Bolt - Marine Grade Stainless steel with TORX Fitting

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

TRAMPA's CLASSIC MONSTER Box is capable of housing up to 2x 6s 22Ah Li-Po Cells & 2x VESC 6 speed controllers at the same time.

TRAMPA's different sized Monster boxes are all made using 2mm & 4mm thick GR4 Re-enforced Glass Fiber panels. The Base & Split Lid panels have been CNC machined with a 2.1mm groove to allow the 2mm thick side panels to slot in & inter-connect perfectly, giving a very strong & tight construction to the box. The box is held together with Anodised Aluminum Hex Spacers which use Stainless Steel Dome Headed TORX Bolts that in turn use lock-tite for permenant connection are screwed through the base of the box, whilst Stainless Steel Countersunk TORX Bolts mounted in a Anodised decorative washers are then used to screw the lid down into the Hex Spacers giving an incredibly neat tight strong & smart finish to the assembly.

As the Box uses the latest Split lid & Inspection pit, it is possible to undo the Countersunk Lid Bolts & remove either the Battery Lid-Side or the VESC Lid-Side of your box, should you ever wish to remove your batteries or take out a VESC without collapsing the entire box down.

Fitted to the top of the Monster Box is the Inspection Pit. Turning the thumb screw on the top gives you access to the Battery Charge Cable & Balance leads that are pushed through rubber grommets to stop the ingress of moisture & dirt, & preventing you from having to open the entire box to do your charging & balancing. 

The Classic Monster Box connects to a TRAMPA Mountain board deck using a Universal Mount & is top side mounted between the riders feet. The Power Cables for the motors exit the box through water resistant Rubber Grommets from the underside of the box, feeding into the protected grooved channels of the WINGS running under the riders feet, eventually poking out at the rear of the deck where the motors are waiting to be connected.

The MONSTER Box is surface mounted to give maximum ground clearance when riding off road. The majority of TRAMPA products are designed to be ridden off road. When you ar riding off road you need extra clearance or you will get snagged up on anything that protrudes from the ground, bashing your battery box on rocks is not a good idea, plus mounting the box on the surface in the way that we do using the universal mount means we retain 95% of the flex of the deck that the TRAMPA decks are so much famed for.

​When installing your chosen batteries into your MONSTER BOX, it’s a good idea to secure them to the base with Velcro, then pad the area around the batteries with good quality foam. This reduces any ride-ruining-rattling sounds whilst keeping the batteries safe from bouncing around when riding over rough terrain.

If you are running full power using the VESC Speed controllers & want good temperature control then it is worth while considering adding a VESC 6 Heat-Sink or two with your purchase.

The Monster Box is NOT Waterproof. It is at best Splash Proof. If submerged into water then you are in trouble. Its best to avoid puddles as you do not know how deep they are. I use puddles as something to carve around and turn them into something fun, (The TRAMPA Stunt Monkey can jump the puddles!) and if you are using this product in an outside environment when its likely to get covered in mud and splashy water like we do with our Mountainboards, then it is wise practice to protect your equipment & add a Monster Box cover. The Thicker Luxury Monster Box cover is fitted with long pockets down the side to store your WAND Controller or critical tools needed on a ride with a removable 'Velcro' top strip that easily peel off allowing you to get access to the inspection pit without having to remove the entire & potentially muddy cover, which just makes life that bit easier. It is my advise to cover the Luxury cover with the Monster Box Muck off or splash proof cover. The Nylon Splash proof cover adds more moisture & dust protection, and adding them both means you keep your luxury cover as clean as possible, but still have access to the charging & balance cables whilst gaining maximum water proofing protection to your equipment

Battery Box Width - 205m
Battery Box Length - 190mm
Box Height - 74mm  

In this Kit you get the following parts

This box is made up of the following parts:
1x CLASSIC MONSTER BOX BASE
1x CLASSIC MONSTER BOX LID - Battery Side
1x CLASSIC MONSTER BOX LID - VESC Side
2x CLASSIC MONSTER BOX - SIDE PANEL x2
1x CLASSIC MONSTER BOX - BLANK END PANEL
1x CLASSIC MONSTER BOX - 2X VESC 6 PANEL
1x CLASSIC MONSTER BOX - INSPECTION PANEL
1x CLASSIC MONSTER BOX - Inspection Panel LID
1x 18650 UPPER PCB For TRAMPA's MONSTER Box Battery kit
1x 18650 LOWER PCB For TRAMPA's MONSTER Box Battery Kit
1x Upper Glass Fibre Panel for 18650 Pack
1x Lower Glass Fibre Panel for 18650 Pack
2x Cell Spacers for 18650 Battery Pack
24x M3 x 65mm Threaded Hex Spacer - Aluminum - Anodised Orange
24x M3 x 10 Countersunk TORX Bolt
24x M3 x 12 Countersunk TORX Bolt
1x Universal PCB BRIDGE Cable for PCB GEN I Battery Packs
1x 18mm to 6mm Heat Shrink Cable - BLACK 30cm Strip
-------------------------------------------------------------------
External Box Length - 271mm
External Box Width - 210.5mm
External Box Height - 87mm
Empty Internal Box Length - 251mm
Empty Internal Box Width - 193mm
Empty Internal Box Height - 81mm
Weight: 2,134g
What colour LED Power Switch do you want in your Monster Box?
What colour LED Power Switch do you want in your Monster Box?

BLUE Power Switch
BLUE Power Switch

GREEN Power Switch
GREEN Power Switch

PINK Power Switch
PINK Power Switch

RED Power Switch
RED Power Switch

WHITE Power Switch
WHITE Power Switch

YELLOW Power Switch
YELLOW Power Switch

What colour Inspection Pit Thumb Screw do you want
What colour Inspection Pit Thumb Screw do you want

Inspection Pit Thumb Screw - BLACK
Inspection Pit Thumb Screw - BLACK

Inspection Pit Thumb Screw - BLUE
Inspection Pit Thumb Screw - BLUE

Inspection Pit Thumb Screw - BRONZE
Inspection Pit Thumb Screw - BRONZE

Inspection Pit Thumb Screw - GOLD
Inspection Pit Thumb Screw - GOLD

Inspection Pit Thumb Screw - GREEN
Inspection Pit Thumb Screw - GREEN

Inspection Pit Thumb Screw - GUNMETAL
Inspection Pit Thumb Screw - GUNMETAL

Inspection Pit Thumb Screw - PINK
Inspection Pit Thumb Screw - PINK

Inspection Pit Thumb Screw - PURPLE
Inspection Pit Thumb Screw - PURPLE

Inspection Pit Thumb Screw - RED
Inspection Pit Thumb Screw - RED

Inspection Pit Thumb Screw - SILVER
Inspection Pit Thumb Screw - SILVER

Quantity required:
We have enough parts to make…  
RRP £550 - each

Excluding VAT
HCC: 7019650019

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon