This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.

HYPA WHEELS Showing with 8 Inch DIAMOND Tyres

HYPA WHEELS Showing with 8 Inch DIAMOND Tyres HYPA Hub 3.75x 2 Inch - Any Colour you like! M4 x 35mm Socket Capped Allen-Key Bolt - Marine Grade Stainless steel with locking paste M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts DIAMOND TREAD 8 inch Tyre measure 3.75x 2x 8 Inch or 200x50mm with 3.75 inch Rim fits all 3.75 inch Hubs HYPA WHEELS Showing with 8 Inch DIAMOND Tyres 7 Inch Inner Tube - INNOVA
RRP FROM
£35+

TRAMPA's 6 spoke HYPA Hub is by far the sexiest, as well as being the strongest, 3.75-inch hub on the market today!

The HYPA hubs 6 spoke design is technically advanced & is manufactured using original Du-Pont materials & the very latest in precision injection molding machinary - No quality expense is spared!  This delux combination of technical design, top quality machinary & original genuine materials, creates a product that is far superior to all of our competitiors, resulting in performance that is well beyond normal expectations. This extra performnce means the TRAMPA HYPA hub can handle much higher than recommended tyre inflation pressures, generting substantially higer than normal roll speeds. During testing our crash test dummies (i mean the Team riders) commonly rode with these hubs well above 80psi & beyond.... When resting at the top of the mountain we measued Joels pressure at 110psi! (110 psi is not recommended!)

The HYPA hubs are held together using only the best Marine Grade (A4) Stainless steel Nuts & Bolts so they definitly wont rust on you (EVER) & are therfore perfect for bad conditions. All the Bolts used by TRAMPA have been dipped in a special Blue Locking Paste & all the Nuts are fitted with the world renowned Nylon "Nylock" Nut locking System, all these no expense spared small details ensure you get the absolute best hub possible!

HYPA hubs are available in loads of different colours & surface finishes, all of which are TRAMPA embossed between the spokes proving the top quality! Do not buy imitations as they will not perform the same!  TRAMPA’s own high class Steel Bearings, (Genuine  ABEC 5 rated Bearings) push perfectly into the HYPA hub bearing housing, guaranteeing the fastest spin rate to the wheel possible. Use either Bearing reducer sleeves into 12mm Bearings or use TRAMPA's 10mm Bearings to fit the HYPA hubs onto 9.52mm skate axles. HYPA hubs are compatible with all known 8-inch tyres currently on the market including MBS & Scrub. Put quite simply – HYPA hubs are by the Best!

Along with many other applications that these wheels will fit too, the HYPA hub will fit and accept ALL the other brands of mountainboards on the market including MBS, SCRUB & KHEO, so when you are looking for an upgrade to your ride you know where too look! Basically the HYPA will fit to anything that uses a Imperial 7/16ths (9.52mm) or 12mm bearings to fit onto the axle. If you already have your own 12mm bearings there are conversion spacers available to convert your 12mm bearings to work on the 7/16ths Imperial (9.52mm) skate axles and a different size spacer to convert them to fit 10mm (metric) scooter axles (see associated parts for details).

Bearings are supplied at a discounted price when purchased with hubs... TRAMPA ABEC 5 Bearings are normally £1.88 each (£15 per set of 8) but when they are purchased with a set of hubs they work out at only £1.25 each which is only £10 per set of 8 bearings when purchased with hub set) giving you a £5 Saving per set!


   

M4 x 35mm Socket Capped Allen-Key Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 35mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This Bolt is used to assemble the TRAMPA HYPA HUBS. The socket capped head of the Bolt fits neatly into the Bolt housing of the HYPA HUB marrying into the M4 nut located in the housing on the other side of the hub.

Weighing just 3 grams each these bolts are very lightweight. They look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

You will need a 3mm Allen Key to tighten & loosen the Nuts & Bolts from the hub. Ensure all your Nuts & Bolts are tight before riding!

M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts

Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts

This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or  8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!

HYPA Hub 3.75x 2 Inch - Any Colour you like!

TRAMPA's 6 spoke HYPA Hub is by far the lightest & weight for weight compared, the strongest 3.75-inch hub on the market today!

The HYPA hubs 6 spoke design is technically advanced & is manufactured using original Du-Pont materials & the very latest in precision injection molding machinery - No quality expense is spared! This deluxe combination of technical design, top quality machinery & original genuine materials, creates a product that is far superior to all of our competitions, resulting in performance that is well beyond normal expectations. This extra performance means the TRAMPA HYPA hub can handle much higher than recommended tyre inflation pressures, generating substantially higher than normal roll speeds. Back in the day during testing, our crash test dummies (i mean the Team riders) commonly rode with these hubs well above 80psi & beyond.... 

The HYPA hubs are held together using only the best Marine Grade (A4) Stainless steel Nuts & Bolts so they definitely wont rust on you (EVER) & are therefore perfect for bad conditions. All the Bolts used by TRAMPA have been dipped in a special Blue Locking Paste & all the Nuts are fitted with the world renowned Nylon "Nylock" Nut locking System, all these no expense spared small details ensure you get the absolute best hub possible!

HYPA hubs are available in loads of different colours & surface finishes, all of which are TRAMPA embossed between the spokes proving the top quality! Do not buy imitations as they will not perform the same!  TRAMPA’s own high class Steel Bearings, (Genuine  ABEC 5 rated Bearings) push perfectly into the HYPA hub bearing housing, guaranteeing the fastest spin rate to the wheel possible. Use either Bearing reducer sleeves into 12mm Bearings or use TRAMPA's 10mm Bearings to fit the HYPA hubs onto smaller sized skate axles. HYPA hubs are compatible with all known 8-inch tyres currently on the market including MBS & Scrub. Put quite simply – HYPA hubs are by the Best!

Along with many other applications that these wheels will fit too, the HYPA hub will fit and accept ALL the other brands of mountain boards on the market including MBS, SCRUB & KHEO, so when you are looking for an upgrade to your ride you know where too look! Basically the HYPA Hub will fit to anything that uses a Imperial 7/16ths (9.52mm) or 12mm bearings to fit onto the axle. If you already have your own 12mm bearings there are conversion spacers available to convert your 12mm bearings to work on the 7/16ths Imperial (9.52mm) skate axles and a different size spacer to convert them to fit 10mm (metric) scooter axles (see associated parts for details).

Bearings are supplied at a discounted price when purchased with hubs...

Rim Diameter 3.75 Inch
Rim Width      2 Inch or 50mm
​Fits all Tyres with 3.75 Inch rim inflating up to 8 inch in Diameter

 

DIAMOND TREAD 8 inch Tyre measure 3.75x 2x 8 Inch or 200x50mm with 3.75 inch Rim fits all 3.75 inch Hubs

INNOVA's 8x 2x 3.75 Inch DIAMOND TREAD tyre is a time tested Classic styled highly purposed All Round Tyre, a design you may well have seen over the years on other devices such as BMX or Mountainbike which is the kind of influence we turn to for inspiration. 

Made from relatively softish rubber with a relatively close cut grip pattern on a relatively ballooned shaped tyre, the 8 Inch DIAMOND TREAD Tyre is a perfect all rounder option, giving great grip on hard packed surfaces & relatively good grip when heading off road specially during the summer months. I would not describe the Diamond treads as being suitable for the most extreme of off road rides, but for everyday use in a warm dry climate they are great.

Measuring 3.75 Inches at the rim, the 8 inch Diamond Tread Tyre will fit to all of TRAMPA's 3.75x 2 Inch Hubs for exact fit, but will also fit to the 3.75/4 x 2.5 Inch Hubs. When fitting the 2 Inch wide Tyres to the 2.5 Inch Rims it gives the tyres a stretched & a lower profile appearance, consequently more surface area.... Some guys really like to do this....

Diamond Treads are available in 8 & 9 Inch, so should you wish to put 9 Inch Diamonds on the rear & 8 Inch Diamonds on the front (putting 8 on the front & 9 on the rear gives your motorised TRAMPA Deck 'more grip on the drive wheels' whilst still keeping the front end 'light & nimble' if you look at pretty much all 4 wheeled motor sports, they nearly always put larger wheels on the rear) you can do, however, you must take the hub with 4 Inch Rims to be able to fit the larger 9 Inch Tyres with 4 inch rims...

Its true, the more you inflate your Tyres the faster you will roll! It also true that if you inflate your tyres too high or too low you will also wear out your tyres mush faster. The official maximum inflation pressure set by the factory for the DIAMOND Tread 8 Inch Tyre is 50psi, but the DIAMOND Tyres are made so well & the TRAMPA Hubs are so strong (The tyres are only as strong as the hubs they are fitted too & our hubs are incredibly strong) that our Crash test Dummies (I mean Team Riders) have been known to inflate these Tyres well beyond their recommended pressures with no problems to mention. Its also true that over inflating your tyres may lead to an explosion which could seriously injure you, so use a pressure guage if your going to inflate them high. If you do decide to go beyond the max inflation pressure ensure your nuts & bolts are tight & once your done riding at the high pressure deflate them back down to a regular pressure, HOWEVER, through years of testing & under mutual agreement with the team, depending on how you ride & how much you weigh & what surfaces your mostly riding, we recommend you should look to inflate these tyres to somewhere between 25 & 35 psi for optimal use.

HYPA Hubs have a 3.75 x 2 inch rim & will fit all tyres up to 8 inches in diameter.  

The HYPA hub is time-proven as being one of the best hubs on the market - We’ve sold tens of thousands of them throughout the years for countless applications - & to this day problems are a rare occurrence!

Made from premium DuPont Plastics, the 6-spoke Hypa hub has an amazing strength-to-weight ratio – weighing just 125g each, they’re the lightest hub in the TRAMPA range! Perfect for freestylers looking to lose every gram off of their board!


Available in a huge range of colours / patterns!

HYPA Hubs use a 2-piece centre-set split-rim design, held together using 6x m4 x 35mm Socket Cap Bolts. Once assembled, can handle up to 50 PSI!





Watch Team Captain Sonnie Dibben talk through the various tyre options




Oversized Longboard Wheels - being 125mm in Diameter, GUMMIES are much larger than any other Longboard wheel on the market! Using High-Quality SUPER SOFT Urethane (75a) with 50mm wide surface contact GUMMIES perform like their name suggests - they’ll grip like gum to the pavement - allowing the most insane turns you wouldn’t believe possible! Thanks to their larger size, GUMMIES Wheels glide over cracks in the pavement & smash through the obstacles that would stop smaller wheels dead.




We all know the pavements & roads are far from a perfect surface - so much so that sometimes it's almost impossible to ride with Longboard wheels. The design brief for the 6.5 inch URBAN TREAD Tyre was simple - make the smallest, best quality pneumatic tyre possible.

The intelligent Jagged-Grip design can be run on high or low inflation pressures. Low pressure gives more grip for muddy corners & trails. High Pressure is perfect for flat-out straight-line speeds! High quality rubber compound & a high TPI (thread-count per inch) make this hub light-weight & hard-wearing!


7” Tyres are a good balance of size & weight. While still big enough to handle rough terrains & build up to impressive rolling speeds, the smaller size helps to save on weight.


7” INNOVA INLINES - With straight cut tread & the ability to handle high PSI, the INLINE  is the perfect option for easy rolling. Working best on smooth surfaces such as skate parks, tarmac or asphalt, the 3mm deep ‘In Line’ grooved surface, encourages the tyre to track in a straight line! Unlike standard Longboard/street style wheels, the pneumatic INLINE tyre is easily big enough to glide over cracks, stones or holes, & will handle hard-packed rougher terrain, such as gravel path with no problem.
 

7” MUD PLUGGERS- Using a deep & aggressive tread pattern that creates 'Grip on top of Grip', with straight sidewalls and a rigid rubber structure, MUD PLUGGERS have a box-ier shape that increases surface contact. Able to run on both low & high PSIs, the wide center bead both reduces rolling resistance and improves traction! Produced using a soft 2PR rubber compound with a high TPI (thread-count per inch), the resulting tyre is amazingly grippy & hard-wearing!


8” Tyres are the first choice for many riders, and are generally considered the “industry standard” when it comes to Mountainboard wheel sizes. Being so popular, and the perfect size for many applications, we offer a HUGE range of 8” tyres!

8” TRAMPA TREAD TYRES - A time-tested favourite among team riders, the TRAMPA TREAD uses an aggressive tread pattern and a choice of hard or soft rubber compound, these Tyres are a solid choice for most terrains! SOFT COMPOUND TREADS are ideal for riding on hard-packed surfaces, whereas HARD COMPOUND TREADS are much better gripping in softer mud
 

8” PRIMO ALPHA TYRES - Using a soft 2PR rubber compound & high TPI (thread-count per inch) - PRIMO ALPHAS are light-weight, grippy & hard-wearing! Its design incorporates a wide center bead to allow & maintain straight line speed, whilst the surrounding tread is beautifully sculpted with wide grooves that’ll give traction regardless of the terrain!
 

8" PRIMO STRIKER TYRE - A favourite among boarder-X racers, the PRIMO STRIKER was designed for fast riding on hard-packed dirt. Made using a hard rubber compound with a Wide Center Bead to help achieve the maximum rolling speeds. The close cut grip pattern around the sides of the tyre gives loads of grip on changeable terrain.
 

8" MUD PLUGGER TYRES - using a deep & aggressive tread pattern that creates 'Grip on top of Grip', with straight sidewalls and a rigid rubber structure, MUD PLUGGERS have a box-ier shape that increases surface contact. Able to run on both low & high PSIs, the wide center bead both reduces rolling resistance and improves traction! Produced using a soft 2PR rubber compound with a high TPI (thread-count per inch), the resulting tyre is amazingly grippy & hard-wearing!
 

8” DIAMOND TREAD TYRE - Made from relatively soft rubber with a close-cut tread pattern & a ballooned-shape, the DIAMOND TREAD Tyre is a perfect all rounder option, giving great grip on hard surfaces & good grip when heading off road - especially during the summer months.
 


8" INNOVA INLINE TYRE With straight cut tread & the ability to handle high PSI, the INLINE  is the perfect option for easy rolling. Working best on smooth surfaces such as skate parks, tarmac or asphalt, the 3mm deep ‘In Line’ grooved surface, encourages the tyre to track in a straight line! Unlike standard Longboard/street style wheels, the pneumatic INLINE tyre is easily big enough to glide over cracks, stones or holes, & will handle hard-packed rougher terrain, such as gravel path with no problem.
 


8" INNOVA SLICKCUT TYRE - Kevlar banding, a high TPI (thread-count per inch), & hard compound rubber make the INNOVA SLICKCUT a light-weight & amazingly strong tyre. The Kevlar banding allows the tyres to handle insane inflation rate, paired with a tread pattern suited for hard surfaces, this is the ultimate tyre for high speed road racing!


 

Rim Diameter 3.75 Inch
Rim Width      2 Inch
 
​Fits all Tyres with 3.75 Inch rim inflating up to 8 inch in Diameter

Use a 3mm Allen Key to tighten the Socket Capped Bolts into the M4 Nuts. When tightening the bolts into the nuts tighten the nuts progressively & equally.

Do not overtighten the Bolts or the nut will spin in its housing!

The Original HYPA hub is time proven as being the best 3.75 Inch hub on the market ever produced. We have sold tens of thousands of them & still to this day its almost un-herd of that any customers ever get a problem using them.
More expensive Hubs dont offer any extra performance, the weight & Strength of the HYPA hub is un-matched by any other hub out there. They might be the cheapest hub we offer but they are the lightest & by far the best value for money by far....

--------------------------------------------------------------
When you purchase this Wheel you get the following parts....
1x HYPA Hub 3.75x 2 Inch - Any Colour you like!
6x M4 x 35 Socket Cap Allen-Key Stainless Steel Bolt
6x M4 Nut - Marine Grade Stainless steel Nylock Nut
1x DIAMOND TREAD 8 Inch Tyre 3.75x 2x 8
1x 7 Inch Inner Tube - INNOVA
Weight: 445g
What colour Hypa hub would you like ?
What colour Hypa hub would you like ?

Matt BLACK Hypa Hub
Matt BLACK Hypa Hub

Matt GREY Hypa Hub
Matt GREY Hypa Hub

CHROME HYPA Hub(+£5)
CHROME HYPA Hub(+£5)

BLACK Gloss Hypa hub (+£2.50)
BLACK Gloss Hypa hub (+£2.50)

BLUE Hypa Hub (+£5)
BLUE Hypa Hub (+£5)

CARBON Print Hypa hub (+£5)
CARBON Print Hypa hub (+£5)

RED Hypa Hub (+£5)
RED Hypa Hub (+£5)

WHITE n Black Hypa hub (+£5)
WHITE n Black Hypa hub (+£5)

WHITE n Blue Hypa hub (+£5)
WHITE n Blue Hypa hub (+£5)

WHITE n Red Hypa hub (+£5)
WHITE n Red Hypa hub (+£5)

Winter Camo Hypa hub (+£5)
Winter Camo Hypa hub  (+£5)

Quantity required:
We have enough parts to make…  
RRP FROM £35 - per wheel

Excluding VAT
HCC: 9503001000

Approx price :
To see shipping prices delivered to your door please create an account and be logged into the system, so the system knows where you are and how much to quote you......

Related Products

menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon menu-icon