Home»Clearance Corner»EMB 34 - 16ply 35º 9/69 HOLYPRO Electric TRAMPA Deck with Classic Box VERTIGO Trucks 9 Inch MEGASTAR Wheels PRO BELT DRIVE Motor Mount, TWIN 6364 154Kv Motors Ratchet Bindings & Heel Straps

Ratchet Binding Footstrap & Ladder - Black straps on Black Foam

TRAMPA Ratchet style foot-straps are the strongest & most Sturdy bindings on the market! Ergonomically designed to ensure a comfy fit, TRAMPA Bindings will keep your feet, locked into the perfect position, enabling your board to be as responsive as it should.? The L Brackets are connected to the footstraps using Marine Grade Stainless Steel Extra Wide DOME HEADED BOLTS. These will not "Pull through" or interfere with the comfort on the side of your foot what so ever.... 

Our amazing foot-straps have a special "SLOT" on the top of the plastic strap to allow the "90º Hook" (found on the base of the Ratchet or Camlock Buckle), to locate into.  This special slot locks the Buckle perfectly into place, eliminating any potential movement. A special Marine Grade Stainless Steel STAR NUT pushes into the foam from the underside of the strap & a 8mm countersunk bolt tightens the buckle firmly into the strap. Replacement foot-straps are sold as pairs & will fit both RATCHET & CAMLOCK Buckles. Ladder straps are sold separately.

Camlock Buckles fit too Footstrap & Heelstrap Bindings

The Camlock Buckle is an integral part of the Camlock Binding. Using a Marine Grade Stainless Steel M5 x 8mm Counrtersunk bolt to screw into a submerged Star Nut that is housed within the TRAMPA Ratchet style Footstraps & the TRAMPA Heelstrap Bindings. There is a spacial hook on the underneath of the CAMLOCK that positions into a special slot on the Footstrap. this special hook & Slot enables the camlock to fit very tightly, securing the ladder strap that is fed into it in the correct position whilst giving secure adjustment to the bindings to fit your foot size.

Unlike the Ratchet buckle, the Camlock will not open or close on you regardless of accidents, your bindings will remain in the same open position until the clip is un-done & the ladder is moved into a new position, this means they wont close on you even when deck lands Binding side down making them the perfect choice of binding option for Kite Boarders who potentially do soar great heights into the air whilst making board off maneuvers, inevitably the deck will get dropped, potentially on the bindings and should they close up on you like what might happen to Ratchet style bindings, (Ratchet Bindings are more suited to Mountainboarding) then this will make it very difficult to be able to get your foot back into the bindings especially when you have a huge kite in the air that you are attached to, opening up the bindings whilst the kite is dragging you around can be a real pain in the XXX, so always best to use Camlocks Bindings if you are Kiteboarding.

L Bracket - Anodised SILVER with BLACK logo

TRAMPA L Brackets are made using 5mm thick Extruded T6 Aluminum. They should never fail on you. Once they have been forced through the die, the continuous L shape that comes out the other side is then punched into the shape you can see. Extruding aluminum gives the metal it the strongest molecular structure possible and it comes naturally with a high quality polished finish that is perfect for Anodising or Powdercoating. Before any surface coatings are added the L Bracket is sent away for more polishing, this extra polishing adds boldness to the shade and depth added to the colour. All L Brackets come with a complimenting TRAMPA logo. M5x20mm Dome head bolts hold the L Bracket to the Straps. M6x25mm Countersunk bolts hold the L Bracket to the deck. You can customise the position of the L bracket & strap to your requirements. Fits to all TRAMPA footstraps and most other brands foot straps & is compatible to fit to both MBS & Scrub boards. Ensure all your nuts and bolts are tight before riding!

Ratchet Buckle Powder coated Black

TRAMPA's RATCHET BUCKLE connects to Footstraps & to Heel Straps. The Ratchet Buckles are fundamental component part of the Bindings, the Ratchet Style bindings will not function without them. Ratchet Buckles are mostly commonly used by Mountain Boarders looking for the most secure connection to the Deck. By simply lifting the ratchet lever up & down feeds the strap into the Ratchet Buckle gradually tightening as it goes. You can tighten the strap as much as you comfortably like the bindings to be. To undo the Ratchet Buckle simple apply some pressure to the Release Clip and the straps should simply pull apart.

The Base of the RATCHET BUCKLE has a "Special Hook" The Hook is used to slip into a special slot, anchoring the Ratchet into the footstrap, eliminating any movement in its mounting. This locking into position ensures maximum control over your board through your bindings at all times. A Quick Release Clip, using an extra long lever makes opening the bindings really easy to do, whilst a range of colour coordinating surface protection (colour) options allows you to match up in colour to all of the TRAMPA products on sale. Use an M5x8mm Countersunk Bolt & special Marine Grade Stainless steel STAR NUT to fix the Ratchet Buckle into the Foot Strap. Ensure your nuts & bolts are tight before you ride!

Ratchet Buckle Anodised Silver

TRAMPA's RATCHET BUCKLE connects to FOOTSTRAPS & to HEEL STRAPA. The Ratchet Buckles are a fundamental component part of the BINDINGS, the RATCHET STYLE BINDINGS will not function without them. 

Ratchet Buckles are most commonly used by Mountain Board Riders looking for the tightest connection to the Deck. By simply lifting the ratchet lever up & down feeds the Ladder Strap into the Ratchet Buckle gradually tightening as it goes. You can tighten the strap as much as you comfortably like the bindings to be. To undo the Ratchet Buckle simple apply some pressure to the Release Clip and the straps should simply pull apart.

The Base of the RATCHET BUCKLE has a "Special Hook" The Hook is used to slip into a special slot, anchoring the Ratchet into the footstrap, eliminating any movement in its mounting. This locking into position ensures maximum control over your board through your bindings at all times. A Quick Release Clip, using an extra long lever makes opening the bindings really easy to do, whilst a range of colour coordinating surface protection (colour) options allows you to match up in colour to all of the TRAMPA products on sale. Use an M5x8mm Countersunk Bolt & special Marine Grade Stainless steel STAR NUT to fix the Ratchet Buckle into the Foot Strap. Ensure your nuts & bolts are tight before you ride!

TRAMPA WING for MOUNTAINBOARDS will widen your deck, stiffen the flex, route the cables and increase your overall performance!! 1x Naked Wing, you need 2 Wings per Deck!!

Injection moulded Riser pad, with a foot-hugging W Shaped concave & integrated cable routing channels.

•By widening the deck, & adding extra leverage beneath the toes & heels, which gives you more control of board.

•Channels on the underside allow for under-foot cable routing from the battery boxes to the Motors.

•W-shape helps to relieve foot ache. 

Specifically designed to fit the NEW 9-69 & 9-73 Mountainboard decks, TRAMPA WINGS can also be fitted to ALL TRAMPA Mountainboards(Some modifications to deck pre-summer 2021 shape may required modification)

Anodised Aluminium Cable Tidy for Mountainboard's V1

Anodised cable tidy for electric mountainboard decks.

TRAMPA LOGO Truck Bolt Mounting Panel / Anti-Sink Plate / Cable Tidy

Organise cables with this high-quality carbon Cable tidy.

With M5 holes spaced for mounting over the trucks, these cable tidys are perfect for anyone using non-electric deck, and have cables running over the top of their deck. Used with the M5 coloured spacers

1x 10 Inch squares of Top Quality Jessup Grip tape

Mega Grippy & really easy to apply. Ensure the decks surface is clean & dry before application. Easy to custom shape, simply draw your shape on the back & cut out with Scissors or sharp knife. Remember to use a ruler for clean edges.

CLASSIC MONSTER Box MkV 2WD BASE

The Monsterbox Classic MkV Base connects to all vertical panels in a Monster Box Classic or Double Stack Monster Box Classic, provided the adjacent panels are also Mk5. They are used with grommets to allow entry into the box by the phase and sensor cables, and the edges of the box are where the hex spacers mount. Additionally, the base is where any Monsterbox is mounted to the board. In this case that can be done via the standard bushing system or Dogbone mounting system. This panel is only designed to operate with 2 motors.

TRAMPA CLASSIC Monster Box MKV LID - Battery Side

The Monsterbox Classic MkV Lid rests on top of the side and end panels of the Monsterbox Classic MkV and centers the screws into the hex spacers to hold the box together.

TRAMPA CLASSIC Monster Box MKV LID - VESC Side

The Monsterbox Classic MkV VESC Side Lid rests on top of the side and VESC panels of the Monsterbox Classic MkV and centers the screws into the hex spacers to hold the box together. It also acts as an access terminal, allowing you to conduct simple maintenance such as charging and turning your VESCs on and off without opening up the box.

CLASSIC MONSTER Box MkV 2mm SIDE PANEL

The side panel is a structural component of the Monster Box MkV that connects the lids and base of the box together.

TRAMPA CLASSIC Monster Box MkV END Panel

Structural component, like the side panels, to connect the lids and base of a Monster Box MkV together.

CLASSIC MONSTER Box MkV 2x VESC 6 Mounting Panel

Used for mounting two VESC 6’s on the inside of a Monster Box Classic MkV.

TRAMPA CLASSIC Monster Box MKV Inspection Pit

The Inspection Pit allows easy access to balance leads and other items on the Monster Box Classic MkV.

TRAMPA CLASSIC Monster Box MKV Inspection Pit Lid

The Inspection Pit lid covers and secures the Inspection Pit on the Monster Box Classic MkV.

Belt Tension Roller Housing for 15mm Belts - BLUE

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

Made from T6 Heat-treated Aluminium, these Belt Tension Rollers are to designed to house a premium TRAMPA 608 BEARING, ensuring a smooth and consistent roll while tensioning the belts. Used with 15mm belts on PRO BELT or OPEN BELT DRIVE, as well as MKII Urban Carve Motor Mounts.

Sprung Steel C-CLIP used inside the Belt tension housings to secure 608 bearing

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

These C-Clips ensure the 608 bearing is secure within the Tension Rollers

Step SPACER used for positioning the 15mm Tension Roller on OBD Drive

Ensuring that belts are correctly tensioned and positioned is an important part of setting up and maintaining your board. A poorly tensioned belt is far more likely to snap or slip, both of which are highly undesirable when your belts are also your brakes!

These Spacer-Axles have two functions, correctly positioning the 20mm Tension Roller, as well as providing the housed 608 bearing a snug-fitting axle to spin freely on.

415 long x 16mm wide High Torque Drive (HTD) 5M (5mm Tooth Space) High Power (HP) STRONGBELT for 2020 Mountainboard Pro Motor Mounts

This ia 416mm long x 16mm wide High Torque Drive (HTD) Re-enforced Rubber Belt, which has 5mm Tooth Spacing (5M). This Belt is High Power rated (HP) & arguably over engineered for our application as the belt is made in Germany by the world famous company called STRONGBELT, who usually supply into heavy industry public sector applications which demand much more stringent requirements of any electric skateboard! This belt is used to transfer the power from the Motor & Motor Pulley into power at the rear wheels of a TRAMPA Electric Mountainboard.

TRAMPA opted to set a new standard in E-Skating, becoming the first in the world to fit to all of its E-Boards, a 15mm wide TRANSMISSON BELT. Our standard 15mm belt is almost double the width of nearly all other E-Sk8's out there, they tend to use a flimsy off the shelf 9mm transmission belt which are prone to stretch, slip & ultimately snap. Using a re-enforced 15mm wide High Power Belt reduces stretch, eliminates slip & as a consequence provides a constantly smooth whilst incredibly intuitive power delivery direct to the rear Drive Wheels of your board. When accelerating or engine breaking (KERS), even from a standing start the STRONGBELT power is smooth & does not slip, or strain the motor, it does a damn gooood job!.....

STRONGBELT, as their name suggests, is a Heavy Industry German Brand that usually supplies the likes of Train manufacturers where serious levels of quality with no excuses on failure are expected from the product, as failure for such an item is serious & may result in death! STRONGBELT weave KEVLAR into their Pulley Belts, Kevlar is one of the strongest fibers known to man, its often added into materials to gain extra strength.... STRONGBELT have the best reputation in the Power Transmission Industry for NO stretching or snapping & we have high expectations from this quality item. 

These extra quality details in the production of our electronic motor drives, provides the maximum responsiveness achievable whilst maintaining a super smooth power delivery to the rider at all times. 

10cm of RED 4mm core 1036 Strand Silicon Coated Cable

Allow your Electric board to gain the maximum performance by fitting the very highest quality Electrical Cables & Connectors and let the power in your battery flood out as performance at the rear wheels!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn in production to produce to such a small amount of such a high quality cable, but finally TRAMPA has had what it wanted delivered & we can now supply you with Super high Quality Silicon Cables in RED or BLACK with co-orinating BLACK & WHITE TRAMPA logos to prove the quality & show off the kind of performance your board is capable of! :-)

TRAMPA's gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. The Blaff cables have enclosed in the Besilen insulated​ Silicon Outer sleeve, 1800 Highly flexible TOP QUALITY Copper strands in the center... BLAFF cable is used for the highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation (Trains, Trams, Planes) as they have a global reputation of incredible high standards.

TRAMPA Silicon cables solder perfectly into XT60 & XT90 connectors to give the perfect connection to your power source. A soldering service for a pair of cables is available though TRAMPA when you purchase the cables as pairs,

RED Silicon Casing with contrasting BLACK TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

10cm of BLACK 4mm core 1036 Strand Silicon Coated TRAMPA Logo'd Cable

Allow your Electric board to gain the maximum performance by only fitting the very highest quality Electrical Cables & Connectors to let the power in your battery flood out as performance at the wheel!! Its taken a serious wedge of cash to get what we wanted & a hell of a long time waiting for our turn to produce to such a small amount of cable at such a high quality standard, but finally TRAMPA has got what it wanted & has now taken delivery of its own Super high Quality Silicon Cables in RED & BLACK with contrasting Black & White TRAMPA logos to prove the quality & show off the kind of performance your board is harvesting! :-)

TRAMPA's Gorgeous Silicon cables are made by the same GERMAN company who makes the world Famous BLAFF Cables. BLAFF cable is used for highest demanding jobs where performance is critical. BLAFF's Cables are so good they are used for public Transportation and the likes (Trains, Trams, Planes) as they have a global reputation of incredible high standards. 

Enclosed in the Besilen insulated​ Silicon Outer lies 1800 Highly flexible TOP QUALITY Copper strands in the center...

BLACK Silicon Casing with contrasting WHITE TRAMPA logo's
Copper Core Dimension - 4mm
Outer Casing Dimension - 4.7mm
Temperature Range -
- Flexible use -25ºC / +180ºC
- Fixed laying -40ºC / +180ºC
Normal Voltage Uo/U 300/300V
Copper used weight 38.4kg per 1000 meters = 3.84 grams per centimeter + casing

XT90H-M connector - Male

On most TRAMPA electrical components, you’ll find AMASS XT90 connectors.  With a strong nylon plastic body & cylindrical brass contacts that comfortably fit 10-12 gauge wires, XT90 connectors are rated to handle 90 Amps continuous – but have been tested up to 270A!

Available as standard, or Anti-Spark - we recommend Anti-Spark for connections that are likely to be plugged/unplugged often.

TRAMPA's own 160Kv 6364 2400w DC Brushless High Torque & High Speed Motor with 300mm TEMP Sensor cables Suitable for Single or TWIN Motor Drives!

TRAMPA's very own purpose made 136 KV Fully HALL & TEMPERATURE censored BLDC & FOC 6364 Out-Runner Motor provides 136 RPM per volt @ 1Nm. It has been CUSTOM MADE to handle HIGH VOLTAGE SET-UPS, i.e 26-44V using for example the VESC 4 & 6 speed controller. The Motor easily switches between FOC & BLDC modes running effortlessly in either mode.

The Motor houses Ultra high Temperature Copper & Ultra Strong High Temperature Neodymium Magnets. We designed an Extended & Heat treated 8mm Steel Axle shaft that's locked in position using 5 high precision Japanese Bearings, All screws & fixings used in its assembly are Marine Grade Stainless Steel, this motor easily out performs all & any competition on the market in so many aspects & its applicational use is almost endless!

Our special design allows you to to also fit  metal mesh filters to prevent the impregnation of larger particles ending in your motor! The front sided motor shield is equipped with twelve M4 treads, sitting on a 44mm diameter circle. The extra threads will allow you to mount the motor in the exact angle you wish, so that the three motor cables always sit in the perfect angle towards the mount or deck.

When handling and inspecting the motor the copper's appearance is almost dark red, suggesting very high quality & looks very special on first impression. 

TRAMPA's 118 kv Motor is fitted with an 38.5mm x 8mm (Extra long) Heat Treated Hardened Steel Motor Shaft, which is also fitted with a KEYWAY locator as standard! The extra length of the Axle allows us to fit Extra wide Motor Pulleys, meaning we fit a 15mm HTD 5M STRONGBELT as standard. A wider belt guarantees a much stronger power delivery. The end of the motor axle is supported with the use of a Bearing that is located in a Fixed housing, soaking up the strain of the powerful motor, & eliminating the possibility of bending the motor axle... Two 3x3x8mm KEYs lock the Axle shaft at both ends (1 into the Rotor & 1 into the Motor Pulley), eliminating all & any "Motor slip", thus providing maximum performance to the rider & gaining critical data for the VESC, ensuring all its high tech facilities can run as expected. TRAMPA's special motors are fitted with internal PCB Hall Sensors.

The Can Section of the motor has been Powder Coated White & finished with a very stylish Gold TRAMPA logo whilst the vented Aluminum end plates of the motor have been color coordinated Anodised Black. The Heavy Duty power cables use 4mm Gold Plated Bullet Connectors to connect to a power source. Typically for TRAMPA only Marine Grade Stainless Steel Fixings have been used in the assembly of this motor. & no parts will rust on you. This Motor can be connected to any of the Motor Pulleys in the TRAMPA product Range amongst others out there on the market...

CUSTOM Motor protection Housing - TWIN MOTOR

HALF CAGE  

This filter has been designed for those who want to save as much weight as possible while still maintaining a level of protection against grit and dust. 
 
The filter mesh is 0.15 mm, this will only allow particulates that are small enough to pass through the air gap between motor magnets and the stator. 

Allowing for consistent cooling of the motor while reducing wear on the motor. 

•Available in 10 colours. 

•Aluminium and stainless construction. 

•Compatible with Trampa motor fan. 

Pairing with the MKII Delrin Motor Housings, these fans secure to the ends of 6376 Motors, creating a cooling airflow around the motors - reducing running motor temp, and increasing efficiency! 

Motor Fan - Connects to the end of the Motor & Spins to help maintain temps low

Pairing with the new MKII Delrin Motor Housings, these fans secure to the ends of 6376 Motors, creating a cooling airflow around the motors - reducing running motor temp, and increasing efficiency!

After many different designs and prototypes, this shape has proved the most efficient at creating an airflow that made a real difference to the motors’ performance.
Attaches to the end of motors using 5x M3x16mm Countersunk bolts.

66 Tooth x 16mm wide Slave Pulley with Pressed bearing for axle support - Fits best to 8 inch wheels for V2 & V3 PRO BELT Drive Motor Mounts with 16mm Belts

TRAMPA's 66 Tooth Pro Motor Mount Slave Pulley fits to any of TRAMPA's 8 Inch off road wheels when connecting into the Mountainboard PRO Motor Mount system. The 66 tooth Pulley has been precision milled from super-light-weight & mega strong Heat Treated T6 Aluminum. The pulleys teeth stand 5mm tall, this is the same size teeth as that found on TRAMPA's 15mm wide 'Strongbelt' & when TRAMPA's 460x15mm Premium Strongbelt is wrapped around the pulleys & the belt tension facility has been screwed down the connection between the teeth & the belt becomes so strong it has what we call HIGH TORQUE DRIVE (HTD).  HTD ensures all of the motors Torque is forced through the pulleys to the wheels & when coupled with the amazing VESC 6 & 12s Battery power provides instant smooth unreal Power on tap to the rider!

This 66 tooth Pro Mount Slave Pulley is capable of connecting to all of the wheels (7, 8 & 9 Inch) in the TRAMPA range but we (TRAMPA) only use it when assembling 8 inch TRAMPA wheels into the TRAMPA Pro Motor Mounts! 

But with the use of some very special Threaded Hex Spacers & Socket capped Bolts the 66 Tooth Pro Mount Slave Wheel connects directly to any of the 7 or 8 Inch SUPERSTAR or HYPA Wheel s& very uniquely also into the 3 spoke PRIMO 9 Inch Wheel as well - 1 pulley, 3 uses.... :-)

TRAMPA's special 66 tooth Pro Mount Slave Wheel works in conjunction with all & any of the 13, 14 or 15 tooth Motor Pulley in the range. Changing your Motor Pulley will drastically alter the performance & characteristics of your ride... 13 Tooth is best for Hill Climbing whilst 15 Tooth is best for high speed, 14 tooth will give you all round performance...

To connect to HYPA hubs you'll need 6x 17x4mm Threaded Hex spacers
To connect to SUPERSTAR hubs you'll need 5x 15x4mm Threaded Hex spacers
 

The KEYWAY connects between the Motor Pulley & the Motor Axle Shaft to eliminate slip under power 3x3x8mm

TRAMPA's Motor Axle Shaft to Pulley KEYWAY measures 3 x 3 x 8mm. It connects into the Motor Pulley when mounted onto the motor Axle Shaft & is used to center the pulley on the Axle & to assist in delivering all the power from the motor without slip! This KEYWAY will fit to all TRAMPA motors amongst others.

TRAMPA's Axle length measures 38.5mm (from motor housing to end of shaft) & has a Diameter of 8mm. The centre of the key (3 x 3 x 8mm) sits 16.70mm away from the Motor front. Front side of Motor to Center of Key! Deduct 4mm & you have the length from front side of motor to the start of key....

Custom 15mm wide Motor Pulley 13, 14 or 15 tooth

TRAMPA's 15mm wide 13-15 Tooth Motor Pulleys connect directly to the Motor Axle & are secured into position using a Magnetic Fixing Key & 4mm Locking Grub Screw.

These custom made Motor Pulley Wheels  fit 15mm wide STRONGBELTS, which should never stretch or break whilst at the same time providing a very smooth power delivery to the user - even from a standing start.

Choice of Aluminium or Black Steel. Aluminium Pulleys are perfect for those looking to save every gram possible on their board - Black Steel Pullys are heavier, but much harder wearing.

Changing your Motor Pulley &/or Drive pulley wheels will drastically change the performance of your ride... :-)

13 Tooth
Best performance for climbing steep inclines.

14 Tooth 
Best all-round performance

15 Tooth 
Best performance forreaching top speeds.

VESC 6 CNC Aluminum Heat Sink Silicone Sealed Housing

CNC T6 Aluminum box Houses the VESC 6 perfectly

Measures 75 x 70 x 18mm

PRO BELT TUB - Fits to both V2 16mm & V3 20mm Pro Belt Tub Covers

CNC’d from a solid block of T6 heat-treated Aluminium, the V3 PRO BELT MOTOR MOUNT TUB is built around keeping the drive train securely & accurately attached, while running as smoothly as possible. Paired with the specially designed CNC’d COVER, the completed tub keeps the elements outs, the gears & belts clean & dry, & the whole board running smoothly.

Attaching T6 Aluminium BASH GUARDS (left & right) ensures the Tub will survive every knock & bump the drive system is bound to receive on a ride.
Special cutouts on the sides of tub allow snapped belts to be ejected out & away from the drive train, preventing any jammed gears or wheel lock.

The Tub is perfectly symmetrical allowing it to slide onto left or right drive trains.

16mm BELT PRO Belt TUB COVER - V2

The Pro Belt Tub Cover is crucial to keeping your drive system free of dirt & debris. CNC’d from Premium Aluminium, giving it the perfect weight-to-strength ratio, the cover slots tightly over the Pro Belt Tub, perfectly sealing off the drive system.

PRO Belt Motor Mount Bash Guard - LEFT (REGULAR)

Made using hardened steel, the PRO BELT bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the left drivetrain.

PRO Belt Motor Mount Bash Guard - RIGHT (GOOFY)

Made using hardened steel, the PRO BELT bash guards are designed around taking the brunt of any hits away from the drive train.

Fits to the left drivetrain.

16mm PRO Belt Drive Motor Connector with 608 Bearing - SILVER ONLY

Housing a precision bearing for Motor Axle Support the PRO BELT DRIVE Motor Adaptor is used for attaching the motor securely to the drivetrain.
Precision CNC’d from hardened steel, the Motor Adaptor also allows for the use of PRO MOTOR HOUSING.

Mountainboard Motor Mount V-Ring TUB Seals - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

Mountainboard Motor Mount Truck Connector

Works with PRO BELT & SPUR GEAR Drives.
The Clamp housing slips over the axels of Precision CNC’d Vertigo Trucks, ensuring the drivetrain sits at the correct angle.
Working in conjunction with the Conical Clamp, when connected together the housing squeezes the clamp to the hanger, securely attaching the drivetrain to the trucks.

Precision CNC’d from T6 Heat-treated Aluminium.

Mountainboard Motor Mount Connector Conical Clamp

Works with PRO BELT & SPUR GEAR Drives.

Designed to work in conjunction & attach securely to Precision CNC’d VERTIGO trucks, the Conical Clamp slips tightly over the CNC’d square on the hanger of the trucks. When attached to the Clamp Housing, the Conical Clamp tightens around the hanger, ensuring secure & accurate Motor Mount attachment.

Precision CNC’d from T6 Heat-treated Aluminium.

Mountainboard Motor Mount Rubber pad for Conical Clamps - Fits both BELT & SPUR Gear Drive Motor Mounts

This rubber seal fits to the PRO BELT DRIVE & the SPUR GEAR DRIVE, and prevents dust & dirt from getting inside the motor mounts. Like many parts, you should check over & clean this seal after every few rides, to ensure it’s doing its job, and it isn’t on it’s last legs!

When installing this seal, be sure that the ‘V-side’ of the seal is facing outwards, towards the tub. You may need to get a small knife or ruler to slip behind and reposition it as you go.

M5 x 8mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-Ratchet Bindings

-Camlock Bindings

-Heelstraps

-3d Sprung Steel Flex Brake

M5 x 8mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-Ratchet Bindings

-Camlock Bindings

-Heelstraps

-3d Sprung Steel Flex Brake

M5 x 12mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-Ratchet Bindings

-Camlock Bindings

-Heelstraps

M5 x 20mm EXTRA WIDE Dome head Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

This Bolt is DOME HEADED, meaning that when screwed into position it sits low & neatly over the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-Bindings

M5 x 25mm EXTRA WIDE Dome head Allen-Key Bolt - Marine Grade Stainless steel with locking paste used for fixing Heel Straps to Bindings

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

This Bolt is DOME HEADED, meaning that when screwed into position it sits low & neatly over the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

-Bindings

-Heelstraps

M4 x 40mm Socket Capped Allen-Key Bolt - Marine Grade Stainless steel with locking paste

TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA SUPERSTAR HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim of the SUPERSTAR HUB eventually screwing  into the M4 nut on the other side easly.

Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

USED FOR CONNECTING:  

SUPERSTAR HUBS       
MEGASTAR HUBS       
PHATLADS HUBS

M5 x 30mm Socket Capped Head Allen-Key Bolt ISO 4762 Marine Grade Stainless Steel

TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA SUPERSTAR HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim of the SUPERSTAR HUB eventually screwing  into the M4 nut on the other side easly.

Weighing just 3 grams each, they are very lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

M5 x 35mm Socket Capped Head Allen-Key Bolt ISO 4762 Marine Grade Stainless Steel

TRAMPA's M4 x 40mm Socket Capped Bolt is made using A4 Marine Grade Stainless Steel. This very special Bolt is specifically made for TRAMPA & is used to assemble the TRAMPA SUPERSTAR HUBS. The socket capped head of the Bolt screws neatly though the Spokes & into the fixing point in the Rim of the SUPERSTAR HUB eventually screwing  into the M4 nut on the other side easly.

Weighing just 3 grams each, they are very lightweight, look very sexy & are totally non corrosive. Using Marine Grade Stainless Steel, means these Bolts will never rust on you! They can cope with the most harsh of weather conditions & they laugh in the face of sandy/salty beaches or muddy freeride tracks, which do turn other manufacturers Nuts & Bolts into corrosive rusting wrecks! As well as being Non Corrosive all of the TRAMPA Bolts are diped in  BLUE THREAD LOCKING PASTE to ensure an extra strong secure fix between the Nut & the Bolt.

M6 x 25mm Bolt - Fixes Trucks to HolyPro Decks - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

You’ll need 8 of the TRAMPA M6 x 25mm Marine Grade Stainless Steel Bolts & 8 of the TRAMPA M6 Stainless Steel Nylock Nuts to attach a pair of TRAMPA Skate Trucks to any TRAMPA Deck with Risers. You’ll also need a pair of 10mm ring spanners to tighten and loosen the Nuts & Bolts. Don’t forget to make sure you’re Nuts & Bolts are tight before you ride!

M5 x 20mm Regular Hex Head Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M5 x 10mm TORX Countersunk Bolt - Marine Grade Stainless steel with TORX Fitting

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M3 x 18mm TORX Countersunk Head Bolt Marine Grade Stainless Steel

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

BIGGEST Beast Box

M5 x 25mm TORX Countersunk Bolt

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M6 x 35mm TORX Countersunk Bolt Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M3.5 x 12 PAN Headed TORX Bolt. - Used to secure the WINGS to the TRAMPA Deck

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 16mm TORX Socket Capped Head Bolt ISO 4762 Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 4mm Grub Screw M4 x 4mm Motor Pulley Grub Screw - Connects the Motor Pulley onto the Motor Axle Shaft

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 Nyloc Nut - Marine Grade stainless steel Nylock Nut - Hub Nuts

Introducing TRAMPA's M4 (4mm Shaft) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M4 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to tighten to the M4 Socket Capped Bolts that hold the HYPA & SUPERSTAR hubs together. To fit the nuts M4 use an 8mm spanner or  8mm Ratchet Socket to turn the Nut onto the Bolt whilst holding the bolt with a 3mm Allen Key. Always ensure your Nuts & Bolts are tight before you ride!

M5 Nut - Marine Grade Stainless steel Nylock Nut - Fixes to Trucks & Bindings

Introducing TRAMPA's M5 (5mm Thread) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M5 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M5 Bolts that hold the TRUCKS to the DECK for all  Decks & also for the Dome Head Bolts connecting the L BRACKETS to the Bindings. Use an 8mm spanner or Ratchet Drive to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M5 Nut - Marine Grade Stainless steel Nylock Nut - Fixes to Trucks & Bindings

Introducing TRAMPA's M5 (5mm Thread) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M5 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M5 Bolts that hold the TRUCKS to the DECK for all  Decks & also for the Dome Head Bolts connecting the L BRACKETS to the Bindings. Use an 8mm spanner or Ratchet Drive to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M5 Nut - Marine Grade Stainless steel Nylock Nut - Fixes to Trucks & Bindings

Introducing TRAMPA's M5 (5mm Thread) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M5 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M5 Bolts that hold the TRUCKS to the DECK for all  Decks & also for the Dome Head Bolts connecting the L BRACKETS to the Bindings. Use an 8mm spanner or Ratchet Drive to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M5 Nut - Marine Grade Stainless steel Nylock Nut - Fixes to Trucks & Bindings

Introducing TRAMPA's M5 (5mm Thread) A4 Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M5 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK thread locking security System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M5 Bolts that hold the TRUCKS to the DECK for all  Decks & also for the Dome Head Bolts connecting the L BRACKETS to the Bindings. Use an 8mm spanner or Ratchet Drive to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

M6 Nut - Marine Grade Stainless steel Nylock Nut - Fixes Bindings & Trucks to Deck

Introducing TRAMPA's M6 (6mm Thread) A4 Grade Marine Grade Stainless steel Nylock Nut. This Nylock Nut will fit to all M6 Bolts regardless of their length. This A4 Marine Grade Stainless Steel Nut will never rust on you! It is fitted with the world renowned NYLOCK System (Nylock is a nylon locking system where Nylon is pasted into the threads of the nut so that when the bolt is tightened into the nut the nylon grabs the thread of the bolt holding it locking it in the thread ensuring things do not vibrate loose or fall off when being ridden on rough terrain like that which a Mountain or Kiteboard endures. The NYLOCK System is fitted as standard to all TRAMPA Nuts. 

This Nut is used to fix to the Regular shaped M6 Bolts that hold the TRUCKS to the DECK for the HOLYPRO Decks & also for the countersunk bolts connecting the L BRACKETS TO the DECKs. Use an 10mm spanner or SOCKET for a Ratchet Driver to tighten the Nut onto the Bolt. Always ensure your Nuts & Bolts are tight before you ride!

7/16ths Nut - Marine Grade Stainless steel Nylock Axle HALF nut (W7/16-20T UNF) - Fits to 12mm Axles

This very special 7/16_^ths of an inch Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut.. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore further reducing weight in the Truck! A few Grams here & a few grams there soon adds up & makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area, where a few grams makes all the difference...

This very special 3/8_^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W7/16 - 20T - UNF. This Nut is used to hold the wheels onto the axles of the Spring Trucks fitted with 12mm axles. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 16mm or 5/8th_^ths of an Inch spanner to tighten / loosen the Nut onto the Axle or Kingpin. Do not overtighten the nut & make sure the wheel can spin freely but does not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

M5 Star Nut - Fixes Ratchet & Camlock to footstraps - Marine Grade Stainless steel

TRAMPA's M5 STAR NUT fastener is used for fixing the RATCHET or CAMLOCK to the BINDING FOOTSTRAP. This nut is made from Marine Grade Stainless Steel and is Guaranteed never to rust on you! 

The cerated edges of the nut cut into the foam of the footstrap & create a solid fix into the bindings. The nut pushes into the foam of the Binding holding the Ratchet in the perfect position. As a tip, use an axle spacer to push the STAR NUT into position within the foot strap. It needs a good push into position to ensure it doesnt rip free from the fixing....   Use M5 x 8mm countersunk bolt to fix Ratchet or Camlock into the Footstrap   

Wheel support spacer for all TRAMPA Wheels on 12mm ATB Axles - CNC precision 12mm x 16mm x 18.2mm - CUSTOM

This special Spacer measures 12mm (id) x 16mm (od) x 18.2mm (long) & has 2 uses!. It is firstly known as the Bearing Support Spacer as this Spacer fits between the Bearings of a 6 Spoked HYPA Hub, (when mounting the HYPA wheel onto 12mm Axles) & secondly it is also known as the AXLE SUPPORT SPACER as this spacer is also used to position any of the TRAMPA wheels in the perfect position onto the axles of 12mm TRAMPA Spring trucks....

TRAMPA spacers are produced as one long tube. The Tube is Heat Treated to gain extra strength & is then Bead Polished to give the metal extra surface protection & a shiny best appearance. The tube is then cut to the exact length for precision mounting. 

M5 COUNTERSUNK Washer Anodised

M5 Countersink Washer great way to pimp and customise your board in 10 differnt colours used in conjunction with all our M5 Countersunk bolts great way to finish off your board/project

M5 SOCKET CAPPED Washer Anodised

M5 Socket Caped Washer great way to pimp and customise your board in 10 different colours used in conjunction with all our M5 Socket Capped bolts great way to finish off your board/project

CUSTOM Spring Truck Baseplate - Extruded T6 Aluminum Anodised & CNC precision Milled

The  INFINITY Baseplate will fit to all of the TRAMPA Spring Truck Hangers but is designed specifically to work in conjunction with the Mini Spring Hanger as it houses a NEW Dual Spring Adjuster position! When the Springs are moved to the new inside position, the new location allows the rider to turn the board very very easily, making it perfect for fast carve riding on all kinds of terrain. You can see the new & growing TRAMPA STREET CARVER range of products here...

The  INFINITY Baseplate is, as its name suggests, designed & built to last forever! Aircraft grade 6061 Aluminum is forced through a Die to create our re-enforced extruded profile. Extruding Aluminum ensures consistent high quality strength. Once Extruded the Baseplate is T6 Heat Treated. Heat treating extruded aluminum fuses the molecules even closer together making it as strong as possible, enabling the INFINITY Baseplate to easily cope with the extreme stresses of all types of off road boarding.

Once Heat Treated, the profile has its fixing holes punched into position & then its Bead Polished in preparation to be Anodised Silver. Once the colour has dried, the Baseplate is then returned to the factory for the precision CNC Machine to accurately mill the Kingpin holes, giving the exact precision required for constructing the Truck.

16 inch wide CNC finished VERTIGO Motor Mount Hanger with 12mm HOLLOW Steel Axles - connects with all Spring Truck Baseplates & Mountainboard Motor Mounts

The TRAMPA VERTIGO ELECTRO HANGER was designed with motor mounting in mind. Using a precise CNC milling machine, we’ve squared off the edges of the hanger, meaning TRAMPA Motor Mounts slide directly (and snugly) onto the hanger. This ensures the maximum amount of support for the motor mounts, and no room for the motors to wobble while riding.

TRAMPA's VERTIGO HANGERs are a slimmed down, lightweight version of the original solid style INFINTY Hanger. To supply the maximum strength at all times all of our hanger bodies are produced from premium FORGED ALUMINUM produced as 1 solid piece. The precision CNC milling machine is applied to the infinity hanger & accurately cuts out the bulk of the material without stripping any of its critical strength, resulting in the VERTIGO hanger being almost as strong as the Infinity BUT nearly 20% lighter in weight. :-)

The Vertigo Hanger is fitted with 12mm HOLLOW STEEL Axles. The Hollow axles are HEAT TREATED - making them substantially stronger & resistant to impacts. Hollow Axles are nearly half the weight of Solid Axles!

CNC milling guarantees precision work - ensuring the Kingpin Holes are accurately placed. This results in the best performance for the rider, as well as making the truck easy to assemble & service. In order to gain the "Two Tone Pimp Finish" the VERTIGO Hanger is ANODISED GLOSS BLACK for metal protection & colour coordinated good looks, before the CNC work is carried out.

The VERTIGO Hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the wheels have a center wheel width of 14 Inches apart.

Custom Kingpin for Spring Trucks - M8x80mm Nikle Plated, Stainless Steel or TITANIUM

This M8 x 80mm Spring Truck Kingpin is used to connect the Hanger & the Baseplate on the TRAMPA'S SPRING & MINI SPRING Trucks. By using an 8mm Kingpin we have managed to save weight whilst retaining all the strength necessary for the job, by using high quality metals!

This M8 x 80mm Kingpin connects into an M6 Nut. You'll need a 5mm Allen key to hold the Kingpin & a 10mm spanner to tighten/loosen your M6 Kingpin Nut.

This Kingpin pushes through plastic bushings before being placed into position in the Truck System. The Plastic bushings allow the metal parts (Hanger & Baseplate) to move inside each other without allowing the metal parts to touch or wear out. The plastic bushings will wear out over time and use and will eventually perish and need replacing. SO, make sure your Bushings are always in good working order after riding riding or when upgrading your Kingpin, it might be time to replace them too due to the unavoidable wear and tear of moving mountainboard parts.

These Kingpins lives up to TRAMPA's incredibly high quality standards, but it's always handy to have a spare just in case you do break one out on a ride....

King Pin bushings 2mm Base for Spring Trucks

The Kingpin Bushings sit tightly in position & hold the Kingpin in a wear-free position between the moving metal parts of the hanger & Baseplate. The Bushings allow the movement (steering) without wearing out the metal parts. The Kingpin bushings are a small item & are subjected to a lot of forces & stress, through regular use they will ultimately wear out & need replacing. Depending on what surface you are riding on & the nature of your riding style will depend on how long these bushings will last you.

To make sure your trucks are always performing at their best you should keep some spare on the shelf at home & inspect these tiny bushings regular basis (preferably before riding) & in particular replace any that are showing signs of wear & then even if they are not broken from time to time replace them anyway...

The difference between the four bushings is the thickness of the base. The different base sizes are 1mm, 1.5mm, 2mm and 2.5mm. 2.5mm is the standard size we work to. As all trucks have 4 bushings this .5mm difference in each of the bushing bases allows us to bridge a maximum distance of 2mm (4x.05mm=2m) resolving any foreseeable problems.

Kingpin Bushings 2.5mm Base - for Spring Trucks

The Kingpin Bushings sit tightly in position & hold the Kingpin in a wear-free position between the moving metal parts of the hanger & Baseplate. The Bushings allow the movement (steering) without wearing out the metal parts. The Kingpin bushings are a small item & are subjected to a lot of forces & stress, through regular use they will ultimately wear out & need replacing. Depending on what surface you are riding on & the nature of your riding style will depend on how long these bushings will last you.

To make sure your trucks are always performing at their best you should keep some spare on the shelf at home & inspect these tiny bushings regular basis (preferably before riding) & in particular replace any that are showing signs of wear & then even if they are not broken from time to time replace them anyway...

The difference between the four bushings is the thickness of the base. The different base sizes are 1mm, 1.5mm, 2mm and 2.5mm. 2.5mm is the standard size we work to. As all trucks have 4 bushings this .5mm difference in each of the bushing bases allows us to bridge a maximum distance of 2mm (4x.05mm=2m) resolving any foreseeable problems.

Kingpin Bushings 3mm Base - for Spring Trucks

The Kingpin Bushings sit tightly in position & hold the Kingpin in a wear-free position between the moving metal parts of the hanger & Baseplate. The Bushings allow the movement (steering) without wearing out the metal parts. The Kingpin bushings are a small item & are subjected to a lot of forces & stress, through regular use they will ultimately wear out & need replacing. Depending on what surface you are riding on & the nature of your riding style will depend on how long these bushings will last you.

To make sure your trucks are always performing at their best you should keep some spare on the shelf at home & inspect these tiny bushings regular basis (preferably before riding) & in particular replace any that are showing signs of wear & then even if they are not broken from time to time replace them anyway...

The difference between the four bushings is the thickness of the base. The different base sizes are 1mm, 1.5mm, 2mm and 2.5mm. 2.5mm is the standard size we work to. As all trucks have 4 bushings this .5mm difference in each of the bushing bases allows us to bridge a maximum distance of 2mm (4x.05mm=2m) resolving any foreseeable problems.

Custom Colour Spring - Powdercoated Sprung Steel Steering Springs

TRAMPA's SPRINGS are coiled to precision & fit into the TRAMPA Spring Trucks perfectly. They easily squeeze into the space between the Baseplate & Hanger & being made to measure they are firstly very easy to fit with no clamps or tools required to squueze them into position & secondly to be super responsive to the rider.!  Once the spring assembly is fitted correctly the steering resistance is taken up instantly!

Our Springs have been designed to work in perfect harmony with the TRAMPA DAMPA's & TRAMPA SPRING RETAINER providing maximum performance from the "Spring assembly" to the rider. The DAMPA's drop into the SPRING & the SPRING RETAINERS seal the ends of the spring, holding the DAMPA in exact position to be pre-loaded & squeezed into the truck. Using just a little bit of muscle, squeeze the loaded spring into the truck, then lock the spring into position using the Spring Adjuster & M5 x 12mm Countersunk Bolt. The TRAMPA spring Truck steering system is highly responsive & totally customisable by interchanging the DAMPA's to harder Urethane. Other Mountain Board brands springs will not fit the TRAMPA Trucks as they are a different in dimension.

TRAMPA Springs are available in a selection of Powder-coated colours for good looks & of course for best surface coating protection & this one comes to you in Powder Coated Black. 

Spring Retainer - Specially designed to work in harmony with the Dampa & spring

TRAMPA's very own & very special re-enforced Spring retainer. Specifically shaped to fit tightly inside the TRAMPA springs & snugly hold the Trampa Dampa in the exact position to give precision steering to the rider. Made by Injection Moulding using original Dupont Materials, with an extra wide Marine-Grade Stainless Steel Flanged Insert seated internally, re-enforcing the Retainer. The Extra Strength of the re-enforced flange, eliminates the need for a very fiddly fitting washer, that is still found in the MBS and Scrub boards today.

Designed to work in harmony with the TRAMPA spring and TRAMPA Dampa to help create immediate resistance from your steering system. With TRAMPA Embossed around the rim of the retainer - you'll have performance with pimpness!

Custom TRAMPA DAMPA

TRAMPA's SPRINGS are coiled to precision & fit into the TRAMPA Spring Trucks perfectly. They easily squeeze into the space between the Baseplate & Hanger & being made to measure they are firstly very easy to fit with no clamps or tools required to squeeze them into position & secondly to be super responsive to the rider.!  Once the spring assembly is fitted correctly the steering resistance is taken up instantly!

Our Springs have been designed to work in perfect harmony with the TRAMPA DAMPA's & TRAMPA SPRING RETAINER providing maximum performance from the "Spring assembly" to the rider. The DAMPA's drop into the SPRING & the SPRING RETAINERS seal the ends of the spring, holding the DAMPA in exact position to be pre-loaded & squeezed into the truck. Using just a little bit of muscle, squeeze the loaded spring into the truck, then lock the spring into position using the Spring Adjuster & M5 x 12mm Countersunk Bolt. The TRAMPA spring Truck steering system is highly responsive & totally customisable by interchanging the DAMPA's to harder Urethane. Other Mountain Board brands springs will not fit the TRAMPA Trucks as they are a different in dimension.

TRAMPA Springs are available in a selection of Powder-coated colours for good looks & of course for best surface coating protection & this one comes to you in Powder Coated Black. 

Spring length - 66.5mm
Spring external diameter - 30mm
Spring internal diameter - 21mm
Spring thickness - 4.2mm
Black Powder coated steel Spring.
Weight: 64g

The TRAMPA DAMPA is a Urethane Elastomer that fits inside the Spring of a Truck. Its purpose is to support the Spring & give extra resistance during steering. Its clever design has three balls stacked & connected on-top of each other. The middle ball is slightly fatter than the outer two, during steering they all compress against each other giving greater feed back in your turns. This stacked design gives a fantastic progressive feel to steering.

By varying the SHORE DUROMETER (Rubber Hardness) strength of the Urethane mixture, we can control the amount of movement in the DAMPA. This in turn allows the rider to custom tune the resistance of their steering perfect to their requirements. The spheres of the DAMPA fit perfectly into the cup of the specially made TRAMPA SPRING RETAINER which is the part that locates & locks the Spring in the the TRAMPA SPRING TRUCKS, and they instantly start to work with the slightest movement from the rider. TRAMPA DAMPA's work in harmony with the rider, supplying the perfect amount of steering resistance whilst eliminating all chances of speed wobble. Now available in 5 different steering resistance's for all levels of rider out there, Orange DAMPA's are for easy steering, whilst White DAMPA's are for the totally committed! 

Turning the Spring Adjuster clockwise pre-loads the tension in the Spring and DAMPA. This can be adjusted on the fly to suit the terrain & conditions. Turning the spring adjuster too much will put pressure on the DAMPA & eventually it may split. Rather than putting too much pressure into the DAMPA, consider up-grading the DAMPA to a harder Shore Durometer as this will most likely increase your performance than over tightening a DAMPA that's not stiff enough for you. Please use the table below for guide.

Spring Adjuster - Marine Grade Stainless Steel

TRAMPA's very own & very special SPRING ADJUSTER is made using A4 MARINE GRADE STAINLESS STEEL & is guaranteed never to rust on you! The Spring adjuster is fitted to the trucks once the springs have been pushed into position. The spring adjuster pre-tensions the steering suitable for the rider’s requirements. We designed the Spring Adjuster to be slightly shorter in length than other brands’, to avoid  the tip of the adjuster poking through the internal of the Spring Retainer, and interfering with the performance of the DAMPA located on the inside of the Retainer.

Should you need extra resistance from your steering because you wish to ride fast, or if you need more steering because the course is twisty, then you can very easily & quickly adjust the resistance of your steering by simply turning the spring adjuster in the correct direction. To get the most out of your trucks on changeable terrain, simply use a 4mm Allen Key to make your adjustments. Winding the Spring Adjuster clockwise increases the steering resistance, which in turn restricts wobble at high speed. Turning the Adjuster anti-clockwise loosens the steering allowing a more carvey ride.  

DO NOT over tighten your Spring Adjuster, as this may crush your DAMPA. If you need more steering resistance upgrade your DAMPA's & do not over tighten!

Longboard & Skateboard Bearings (8 x 22 x 7mm) Red Black Blue White or GREEN Ceramic sidewalls ABEC 7 608

TRAMPA's Longboard bearings will fit to all classic Longboard & Skateboard Wheels.

TRAMPA's Skate sized 608 Bearing (8 x 22 x 7mm) is internationally known as 608 2RS Longboard Bearing or Skateboard Bearing. It is the High Precision stock choice of bearing supplied with all TRAMPABOARDS that use 8mm Axles.

TRAMPA's 608 Skate Bearing has been polished to a an above genuine ABEC 7 quality rating & offers fantastic performance to the user. This Bearing will spin very fast for prolonged periods & it with regular servicing & a few drops of Speed Cream every now & then will last you a very long time. too. The internal Ball Bearings are mounted in a stainless steel raceway & are coated in very fine grease similar to the properties of Speed Cream.

As with all of TRAMPA's Bearings this Longboard Bearing has been fitted with Friction Free (contact-less) Removable Shields making servicing really easy. To Service your Bearings use a sharp knife or 'Pick' to carefully take out the Removable Sleeves from the bearing & clean/soak the bearings in a pot of Petrol or Thinners. Once clean, dry thoroughly & add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

& add a few drops of Speed Cream. A few drops is more than enough so don't go pouring loads in, the oil just needs spreading over all of the surfaces so pop them on the axle & give them a spin to spread the cream evenly & only add 1 more drop of Speed cream if necessary. Remember to wipe up any excess cream spinning out of your bearings onto your wheels as this will attract dust & dirt looking messy in turn.

MEGASTAR 9 OFF-SET Rims Measure 3.75/4x 2.5 Inch & the bearings are positioned OFF-SET & accept 3.75 & 4 Inch Rim Tyres

It was hard to ever imagine that TRAMPA's SUPERSTAR hub could ever be improved upon - but that's just what we’ve gone’n’done! The Super Sexy MEGASTAR Rims are a PRO version of the already amazing SUPERSTAR Rim!

CNC Milled from a solid block of T6 aluminium, polished, anodised (in 10 different colours!) & logo-ed up for a pimp appearance - all of the various MEGASTAR Rims we offer fit the regular SUPERSTAR SPOKES, so if you already use Superstars & fancy an upgrade, you’ll only need to purchase the Rims to make the swap.

MEGASTAR Hubs can handle the highest inflation pressures of any small wheel on the market. Increasing inflation rates ultimately increases maximum roll speeds, making these hubs the perfect option for the insane among us!

MEGASTAR Rims have extra threaded bolt holes for wheel balancing purposes -  the extra holes allow you to screw in 2x extra M4x16mm Socket cap TORX Bolts directly opposite the valve - which in turn counter-balances, creating a smoother rotation &  faster spin rate!

Megastars are available in a variety of sizes, with different spoke/bearing positioning for a number of different applications!

CENTER-SET Bearing position, which is a direct aluminium replacement of the original plastic-injection Superstar rim. Keeping the bearings centrally-located within the hub leaves the wheelbase unchanged, for a nimble feeling & riding board.

Megastar 8 CENTRE SET RIMS fit all 3.75x2 inch Rim Tyres & Regular Superstar / Skinny BB-Star Spokes.

OFF-SET Bearing position moves the wheels further from your feet - widening the boards wheelbase, which in turn increases stability - perfect for large people & small Boards. Initially created in conjunction with narrower Truck Models (12-Fifties & Mini Spring Trucks) in order to grant clearance for bigger tyres or rear-mounted battery boxes.

Megastar 8 OFF SET RIMS fit all 3.75x2 inch Rim Tyres & Regular Superstar / Skinny BB-Star Spokes.

Megastar 9 OFF SET RIMS fit all 3.75x2.5 inch Rim Tyres & Regular Superstar / Phat BB-Star Spokes.

DEEP-DISH Rims are as pimp as it gets! These elongated rims both widen the wheelbase of a board as well as the contact patch of the tyres - improving both stability & grip! While also granting extra clearance for fitting larger tyres or rear-mounted battery boxes.
 

Megastar 8 DEEP DISH RIMS fit all 3.75/4 x 2.5 inch Rim Tyres & Regular Superstar / Skinny BB-Star Spokes.

Megastar 9 DEEP DISH RIMS fit all 3.75/4 x 3 inch Rim Tyres & Regular Superstar / Skinny BB-Star Spokes.

The CENTER SET & OFF SET (3.75 x 2 Inch) MEGASTAR 8 HUBs fit ANY of the tyres in TRAMPA's range up to 8 inches in Diameter - including the 5 Inch Gummies tyres, 6.5 Inch URBAN Treads, 7 Inch Inline tyres & ANY 8 inch tyre option.

The DEEP DISH (3.75/4 x 2.5 Inch) MEGASTAR 8 HUB fits most tyres in TRAMPA's range up to 8 inches in Diameter, widening the tread & increasing the contact patch - including 6.5 Inch URBAN Treads, 7 Inch Inline Tyres & ANY 8 inch Tyre option.

The OFF SET & DEEP DISH (3.75/4 x 2.5/3 Inch) MEGASTAR 9 HUBs fit most of the tyres in the TRAMPA product Range up to 10 inches in Diameter, widening the tread & increasing the contact patch - including the 6.5 Inch URBAN Treads, 7 Inch Inline Tyres & ANY 8, 9 or 10  inch tyre options TRAMPA offers.

TRAMPA's REGULAR SUPERSTAR SPOKES are made from Extruded 6061 Aluminum (Super Strength Aero-grade quality) & comes in a range of colours to satisfy your taste.
TRAMPA’s new BB STAR Spokes are as lush as it gets - CNC’d from T6 Aluminium, available in two models - SKINNY (fits ALL MEGASTAR rims) or PHAT (fits OFF SET MEGASTAR 9 ONLY).

The MEGASTAR's hub construction is held together by using 5x Socket cap M4 x 40mm A4 (Marine Grade) Stainless Steel Nuts & Bolts that'll never rust on you!

Further pimp up your Megastar hubs with M4 Socket Cap spacers - anodised in 10 colours!

TRAMPA's MEGASTAR Hubs can be used in conjunction with any of the Pulleys that fit to SUPERSTAR hubs.

It's possible to fit any Bearing size TRAMPA offers into MEGASTAR Rims. As Standard the Superstar / Megastar spokes accept Mountainboard bearings for 12mm Axles - these bearings can be fitted with Reducer Sleeves that allow the hub to fit to 9.525mm Axles. If you use the Special Spoke Support Spacer into the assembly of the hub, you can fit to 8mm Longboard Axles - where hundreds of top quality bearing options are available to choose from.

CLASSIC 5 SPOKE for or any size MEGASTAR Rim - Extruded T6 Aluminum Heat treated & CNC Precision milled fits all SUPERSTAR & MEGASTAR Wheels

TRAMPA SPOKES for Superstar or Megastar Hubs. TRAMPA's Spokes are produced using T6 Heat-Treated 6061 Aero-grade "Top Quality" Aluminum, which is forced through an Extrusion Die. Our Spokes are made in one continuous piece - once extruded the resulting profile is T6 Heat Treated - making the Alloy extremely strong. 

The spokes are bead polished to take away and sharp edges then the spokes are sent away to the Anodisers to have the relevant colours added. Once the colour has been added the precision CNC machine is put back to work to mill out the bearing housing perfectly. 

Check your spoke support spacers, O-Rings and hardware is in good condition when changing spokes & ensure all of your nuts & bolts are tight before you ride!

CUSTOM Spoke Support spacer - Installing a Spoke Support Conversin Spacer allowsyou to fit SUPERSTAR or MEGASTAR hubs to 9.525mm & 8mm Axles such as Evolve, Boosted & many others

This is the TRAMPA SUPERSTAR Spoke Support Spacer. It is used to gain extra strength for the SUPERSTAR wheel design by adding support to the Aluminum Spokes when the wheel is being used under high inflated pressures...

Precision injection moulded, using original DuPont materials, this Spacer provides essential support for the Spokes in the Superstar hubs. There is a Deep Shelf on the Rim of the Spacer which pushes into the internal side of the Spoke, positioning the Spacer/spoke perfectly for assembly. The thick plastic ensures a very strong support platform maximising Bearing support & spin rate always....

Ensure all your nuts & bolts are tight before riding!!

130mm - Hand made TRAMPA Vinyl Sticker

Everybody loves stickers, especially TRAMPA VINYL stickers! TRAMPA vinyl's are pain-stakingly hand made at TRAMPA HQ using the absolute finest Vinyl material available! So long as the area it is to be stuck to is clean the Vinyl we use is guaranteed to stick well & not fade for well over 5 years. These BLUE vinyl stickers are sized to fit onto the top of the Trampa deck, the dimensions are 130mm long x 28mm high.

There are loads of colours to choose from and the price starts at just 30 pence each - so custom pimping your deck, car, van, boat, bedroom window or any other surface you can think of that would benefit with a TRAMPA logo slapped on it is really easy & cheap to do... Help TRAMPA the world with the Pimp-est vinyl stickers EVER!

To Apply - Ensure the surface is clean & grease free before applying the sticker. Peel the thick side away from the Masking tape so the sticker appears in reverse (negative) and simply lay the masking tape onto the surface in question. Using your fingers or a soft cloth, rub the masking tape, forcing any air out of the vinyl & allowing the vinyl to stick well. Then gently peel away the masking tape to reveal the Vinly. This VIDEO may help...

Everybody loves stickers, especially TRAMPA stickers! TRAMPA's Old Skool VINYL Stickers are pain-stakingly Hand Made at the TRAMPA HQ using the absolute finest Vinyl material available! So long as the area it is to be stuck to is clean the Vinyl we use is guaranteed to stick well & not fade for well over 5 years and most likely much longer! These BLUE Vinyl Stickers are sized to fit underneath the TRAMPA deck, the dimensions are 370mm long x 70mm high.

There are loads of colours to choose from & the price starts at just £2.50 each - so custom pimping your deck, car, van, boat, bedroom window or any other surface you can think of that would benefit with a TRAMPA logo slapped on it is really easy & cheap and easy to do...

Help TRAMPA the world with the Pimp-est vinyl stickers EVER! To Apply the Stickers - Ensure the surface you re applying too is clean & grease free before applying the sticker. Peel the thick side away from the Masking tape so the sticker appears in reverse (negative) and simply lay the masking tape onto the surface in question. Using your fingers or a soft cloth, rub the masking tape, forcing any air out of the vinyl & allowing the vinyl to stick well. Then gently peel away the masking tape to reveal the Vinly.

580mm - Hand made TRAMPA Vinyl Sticker